Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Journal of Solid-State Circuits

A Cryogenic Superconducting Quantum Computing Unit Interface Chipset With Phase-Detection-Based Readout and Phase-Shifter-Based Controller

Yanshu Guo, Yaoyu Li, Wenqiang Huang, Tian Tian, Nan Wu, Xicheng Zhang, Qichun Liu, Tiefu Li, Zhihua Wang, Ning Deng, Yuanjin Zheng, Hanjun Jiang

Published May 27, 2026• 1 citation
Publisher

Abstract

This article presents a cryogenic quantum interface chipset at 3.5 K for superconducting transmon qubit operations. The chipset comprises a phase-detection readout and a phase-shifter-based polar-modulation controller with flexible scalability. With the proposed phase-detection readout scheme, a 9-bit time-to-digital converter (TDC)-based state detector is used to read out the qubit state by detecting the phase difference between the stimulus signal and the reflected signal. A low-IF N-path filter-based receiver and a multi-tone transmitter are co-designed to enable frequency-division multiplexing (FDM) dispersive readout of multiple qubits. A phase-shifter-based polar-modulation XY-driver is developed with support for fast phase quantum gate operation and derivative-removal-by-adiabatic-gate (DRAG) pulse generation. The Z-driver is realized using a static digital-to-analog converter (DAC) array and a 10-bit dynamic DAC for power efficiency. Fabricated in a 28-nm bulk CMOS process, the chipset occupies a die area of 4.6 mm2. The readout RX achieves a noise temperature of 40 K with a gain of 45–83 dB and a bandwidth of 1.2 GHz. The readout RX consumes 32% less power than state-of-the-art designs. The measured total readout power for simultaneous detection of two qubits is 12.2 mW, which is the lowest among readouts with a similar integration level. In addition, the controller achieves a spurious-free dynamic range (SFDR) of 49 dB for a 1-GS/s Z-driver and an SNR of 42 dB for a 1-GS/s XY-driver. The XY-driver consumes 4.3 mW per qubit under active control. Verified with practical transmon qubits, the readout fidelity exceeds 92.6%, approaching that of commercial instruments. A Rabi experiment at 5.61/6.36 MHz, a Ramsey experiment at 4.1 MHz, and a T1 experiment at$9.98~{\mu }$s are also successfully observed using the proposed chipset at 3.5 K.

DOI
10.1109/jssc.2026.3695612

Related papers

A Polar-Modulation-Based Cryogenic Transmon Qubit State Controller in 28 nm Bulk CMOS for Superconducting Quantum Computing

Yanshu Guo, Qichun Liu, Yaoyu Li +10 more

This article presents a cryogenic transmon qubit state controller integrated circuit (IC) working at a temperature of 3.5 K for superconducting quantum computing (QC) applications. The qubit state controller IC comprises a polar-modulation-based XY -path driver and a current-steering digital-to-analog converter (DAC)-based${Z}$-path driver. To generate the XY -path driving pulse with arbitrary envelopes in the frequency range of 4–6 GHz, a switched-capacitor digital power amplifier (DPA) is adopted for amplitude modulation, and an injection locking local oscillator (IL-LO) with a constant-slope digital-to-time-converter (DTC) is used for open-loop phase modulation. With the proposed DPA and IL-LO, the controller can control a qubit with a compact architecture. Fabricated in the 28-nm bulk CMOS process, the controller IC occupies an active die area of 0.9 mm2 per driving channel. The controller achieves a spurious-free dynamic range (SFDR) of 40 dB for a 1 GS/s XY -path driver and an SFDR of 48 dB for a 1 GS/s${Z}$-path driver at 3.5 K. The controller consumes a power of 13.7 mW per qubit. A Rabi experiment at 13.9 MHz, a Ramsey experiment at 3.09 MHz, and a T1 experiment at 15.87$\mu \text{s}$are conducted using the presented controller IC at 3.5 K to control the transmon superconducting qubit at 10 mK directly.

IEEE Journal of Solid-State Circuits•Sep 26, 2023•12 citations

29.4 A Cryo-CMOS Quantum Computing Unit Interface Chipset in 28nm Bulk CMOS with Phase-Detection Based Readout and Phase-Shifter Based Pulse Generation

Yanshu Guo, Qichun Liu, Wenqiang Huang +9 more

Cryogenic CMOS (Cryo-CMOS) ASICs have drawn increasing attention with great potential in scaling down the quantum computing (QC) platform. Recently, several cryoCMOS ASICs have been presented in the literature, including the qubit state readout ASICs [1–4] and state controller ASICs [5–8]. For readout ASICs, the quadrature down conversion architecture is widely adopted, with the power consumption ranging from 20mW [1] to 75mW [2]. Also, significant progress has been made in reducing the power consumption of qubit controllers. The controller in [5] consumes a power of <4 mW/qubit under active control, when controlling a superconducting quantum computing unit cell. Nevertheless, it remains a long-term goal to reduce the power consumption and promote the integration level of readout/controller ASICs, in consideration of the increasing requirement on qubit number and the limited cooling power provided by the dilution refrigerator.

Digest of technical papers/Digest of technical papers - IEEE International Solid-State Circuits Conference•Feb 18, 2024•28 citations

A Cryo-CMOS Low-Power Semi-Autonomous Transmon Qubit State Controller in 14-nm FinFET Technology

Sudipto Chakraborty, David J. Frank, Kevin Tien +23 more

A scalable, non-multiplexed cryogenic 14-nm FinFET quantum bit (qubit) state controller (QSC) for use in the semi-autonomous control of superconducting transmon qubits is reported. The QSC includes an augmented general-purpose digital processor that supports waveform generation and phase rotation operations combined with a low-power current-mode single sideband upconversion${I}/{Q}$mixer-based RF arbitrary waveform generator (AWG). Implemented in the 14-nm CMOS FinFET technology, the QSC generates control signals in its target 4.5–5.5-GHz-frequency range, achieving an spurious free dynamic range (SFDR) > 50 dB for a signal bandwidth of 500 MHz. With the controller operating in the 4 K stage of a cryostat and connected to a transmon qubit in the cryostat’s millikelvin stage, measured transmon$T_{1}$and$T_{2}$coherence times were 75.7 and 73$\mu \text{s}$, respectively, in each case comparable to results achieved using conventional room temperature (RT) controls. In further tests with transmons, a qubit-limited error rate of 7.76 × 10−4 per Clifford gate is achieved, again comparable to the results achieved using RT controls. The QSC’s maximum RF output power is −18 dBm, and power dissipation per qubit under active control is 23 mW.

IEEE Journal of Solid-State Circuits•Sep 20, 2022•53 citations

A Reconfigurable Analog Baseband for Superconducting Qubit Readout

Tian Tian, Yanshu Guo, Zhihua Wang +2 more

Superconducting qubits are promising candidates for building scalable quantum computers, but they require efficient and flexible readout systems that operate at cryogenic temperatures. This article presents a cryo-CMOS analog baseband (ABB) for superconducting qubits readout, which targets flexibly reconfigurable gain, center frequency, and bandwidth. The ABB achieves power and area reduction by integrating programmable-gain amplifiers and filters in one block and by using differential capacitors rather than single-ended ones. The differential-mode gain and common-mode stability of the low-pass filter are improved by negative-impedance inverters. Implemented in 28-nm Bulk CMOS technology, the ABB occupies an active area of 0.016 mm2. It has a tunable gain range from 10.7 to 42.5 dB, a center frequency from 101 to 189 MHz, and a bandwidth from 1.3 to 2.8 MHz. Thus, the ABB enables high-fidelity and low-power readout of superconducting qubits for future large-scale quantum computers.

IEEE MTT-S International Wireless Symposium (IWS)•May 16, 2024•0 citations

A Cryogenic Front-End Module Applied to Readout Two-Qubits with FDM Technology in Superconducting Quantum Computing System

Che-Hao Li, Chien‐Nan Kuo, Changsheng Chen +5 more

A massive quantum bits (qubits) array is required to mitigate gate error rates in order to realize a practical quantum computing system. An integrated broadband front-end module is employed for the readout of two transmon qubits using frequency division multiplexing (FDM) technology. The frontend module features a customized IQ up-conversion mixer, fabricated using a$28-\text{nm}$CMOS process, supporting an RF range of$4-10 \text{GHz}$with a conversion gain of$0.3 \pm 3 ~\text{dB}$at 4 K. It achieves sufficient linearity with third-order intermodulation distortion (IM3) exceeding 45 dB and exhibits image rejection ratio (IRR) and LO rejection ratio (LORR) of 57 dB and 50 dB, respectively. The functionality of the front-end module is validated through the successful readout of two qubits. A readout fidelity of around 80 % is measured, consistent with the baseline result.

IEEE MTT-S International Microwave Symposium digest•Jun 15, 2025•0 citations

A Cryo-CMOS Controller IC With Fully Integrated Frequency Generators for Superconducting Qubits

Kiseo Kang, Donggyu Minn, Seunghun Bae +7 more

Extensive research on quantum mechanics in past decades has successfully paved the way towards the disruptive technology of quantum computing. A further step to the realization of a fault-tolerant scalable quantum computer is presenting challenges in the field of engineering. It necessitates a microsystem operating at 4K in a dilution refrigerator, which would be inevitable to control thousands or millions of qubits sitting at 10mK. There have been IC implementations of pulse modulators generating qubit-controlling microwave signals [1– 4]. The pulse modulation based on direct synthesis demonstrated feasibility of driving multiple qubits with frequency-division multiplexing (FDM) through one RF cable [1 – 3]. The first implementation of a full controller [1], which includes both read and write chains for spin qubits, demonstrated the highest level of integration. However, the previous work used external local oscillator (LO) sources for frequency synthesis. External feeding of LO requires precise matching; otherwise, a failure would cause leakage to the qubit driving output through PCB traces, resulting in AC-Stark shift of qubit state by unwanted tones at near-resonance. It becomes more problematic in FDM-based multi-qubit driving. Since the fidelity of qubit operations strongly relies on the quality of driving frequency, a low-noise LO generation by a phase-locked loop (PLL) is one of the most important factors [5]. The internal generation of LO gives additional benefits in superconducting qubit interface. It necessitates multiple LOs since the superconducting qubit uses microwave pulse driving for both read and write. To detect the state of a qubit through dispersive readout, the phase reflected from the readout resonator should be measured. Therefore, the driving pulses for the read and the write should be synchronized to a single reference timing. Using built-in PLLs sharing a single reference clock naturally solves this problem.

Digest of technical papers/Digest of technical papers - IEEE International Solid-State Circuits Conference•Feb 20, 2022•45 citations
This article presents a cryogenic quantum interface chipset at 3.5 K for superconducting transmon qubit operations. The chipset comprises a phase-detection readout and a phase-shifter-based polar-modulation controller with flexible scalability. With the proposed phase-detection readout scheme, a 9-bit time-to-digital converter (TDC)-based state detector is used to read out the qubit state by detecting the phase difference between the stimulus signal and the reflected signal. A low-IF N-path filter-based receiver and a multi-tone transmitter are co-designed to enable frequency-division multiplexing (FDM) dispersive readout of multiple qubits. A phase-shifter-based polar-modulation XY-driver is developed with support for fast phase quantum gate operation and derivative-removal-by-adiabatic-gate (DRAG) pulse generation. The Z-driver is realized using a static digital-to-analog converter (DAC) array and a 10-bit dynamic DAC for power efficiency. Fabricated in a 28-nm bulk CMOS process, the chipset occupies a die area of 4.6 mm2. The readout RX achieves a noise temperature of 40 K with a gain of 45–83 dB and a bandwidth of 1.2 GHz. The readout RX consumes 32% less power than state-of-the-art designs. The measured total readout power for simultaneous detection of two qubits is 12.2 mW, which is the lowest among readouts with a similar integration level. In addition, the controller achieves a spurious-free dynamic range (SFDR) of 49 dB for a 1-GS/s Z-driver and an SNR of 42 dB for a 1-GS/s XY-driver. The XY-driver consumes 4.3 mW per qubit under active control. Verified with practical transmon qubits, the readout fidelity exceeds 92.6%, approaching that of commercial instruments. A Rabi experiment at 5.61/6.36 MHz, a Ramsey experiment at 4.1 MHz, and a T1 experiment at9.98 μ9.98~{\mu }9.98 μs are also successfully observed using the proposed chipset at 3.5 K.
This article presents a cryogenic transmon qubit state controller integrated circuit (IC) working at a temperature of 3.5 K for superconducting quantum computing (QC) applications. The qubit state controller IC comprises a polar-modulation-based XY -path driver and a current-steering digital-to-analog converter (DAC)-basedZ{Z}Z-path driver. To generate the XY -path driving pulse with arbitrary envelopes in the frequency range of 4–6 GHz, a switched-capacitor digital power amplifier (DPA) is adopted for amplitude modulation, and an injection locking local oscillator (IL-LO) with a constant-slope digital-to-time-converter (DTC) is used for open-loop phase modulation. With the proposed DPA and IL-LO, the controller can control a qubit with a compact architecture. Fabricated in the 28-nm bulk CMOS process, the controller IC occupies an active die area of 0.9 mm2 per driving channel. The controller achieves a spurious-free dynamic range (SFDR) of 40 dB for a 1 GS/s XY -path driver and an SFDR of 48 dB for a 1 GS/sZ{Z}Z-path driver at 3.5 K. The controller consumes a power of 13.7 mW per qubit. A Rabi experiment at 13.9 MHz, a Ramsey experiment at 3.09 MHz, and a T1 experiment at 15.87μs\mu \text{s}μsare conducted using the presented controller IC at 3.5 K to control the transmon superconducting qubit at 10 mK directly.
Cryogenic CMOS (Cryo-CMOS) ASICs have drawn increasing attention with great potential in scaling down the quantum computing (QC) platform. Recently, several cryoCMOS ASICs have been presented in the literature, including the qubit state readout ASICs [1–4] and state controller ASICs [5–8]. For readout ASICs, the quadrature down conversion architecture is widely adopted, with the power consumption ranging from 20mW [1] to 75mW [2]. Also, significant progress has been made in reducing the power consumption of qubit controllers. The controller in [5] consumes a power of <4 mW/qubit under active control, when controlling a superconducting quantum computing unit cell. Nevertheless, it remains a long-term goal to reduce the power consumption and promote the integration level of readout/controller ASICs, in consideration of the increasing requirement on qubit number and the limited cooling power provided by the dilution refrigerator.
A scalable, non-multiplexed cryogenic 14-nm FinFET quantum bit (qubit) state controller (QSC) for use in the semi-autonomous control of superconducting transmon qubits is reported. The QSC includes an augmented general-purpose digital processor that supports waveform generation and phase rotation operations combined with a low-power current-mode single sideband upconversionI/Q{I}/{Q}I/Qmixer-based RF arbitrary waveform generator (AWG). Implemented in the 14-nm CMOS FinFET technology, the QSC generates control signals in its target 4.5–5.5-GHz-frequency range, achieving an spurious free dynamic range (SFDR) > 50 dB for a signal bandwidth of 500 MHz. With the controller operating in the 4 K stage of a cryostat and connected to a transmon qubit in the cryostat’s millikelvin stage, measured transmonT1T_{1}T1​andT2T_{2}T2​coherence times were 75.7 and 73μs\mu \text{s}μs, respectively, in each case comparable to results achieved using conventional room temperature (RT) controls. In further tests with transmons, a qubit-limited error rate of 7.76 × 10−4 per Clifford gate is achieved, again comparable to the results achieved using RT controls. The QSC’s maximum RF output power is −18 dBm, and power dissipation per qubit under active control is 23 mW.
Superconducting qubits are promising candidates for building scalable quantum computers, but they require efficient and flexible readout systems that operate at cryogenic temperatures. This article presents a cryo-CMOS analog baseband (ABB) for superconducting qubits readout, which targets flexibly reconfigurable gain, center frequency, and bandwidth. The ABB achieves power and area reduction by integrating programmable-gain amplifiers and filters in one block and by using differential capacitors rather than single-ended ones. The differential-mode gain and common-mode stability of the low-pass filter are improved by negative-impedance inverters. Implemented in 28-nm Bulk CMOS technology, the ABB occupies an active area of 0.016 mm2. It has a tunable gain range from 10.7 to 42.5 dB, a center frequency from 101 to 189 MHz, and a bandwidth from 1.3 to 2.8 MHz. Thus, the ABB enables high-fidelity and low-power readout of superconducting qubits for future large-scale quantum computers.
A massive quantum bits (qubits) array is required to mitigate gate error rates in order to realize a practical quantum computing system. An integrated broadband front-end module is employed for the readout of two transmon qubits using frequency division multiplexing (FDM) technology. The frontend module features a customized IQ up-conversion mixer, fabricated using a28−nm28-\text{nm}28−nmCMOS process, supporting an RF range of4−10GHz4-10 \text{GHz}4−10GHzwith a conversion gain of0.3±3 dB0.3 \pm 3 ~\text{dB}0.3±3 dBat 4 K. It achieves sufficient linearity with third-order intermodulation distortion (IM3) exceeding 45 dB and exhibits image rejection ratio (IRR) and LO rejection ratio (LORR) of 57 dB and 50 dB, respectively. The functionality of the front-end module is validated through the successful readout of two qubits. A readout fidelity of around 80 % is measured, consistent with the baseline result.
Extensive research on quantum mechanics in past decades has successfully paved the way towards the disruptive technology of quantum computing. A further step to the realization of a fault-tolerant scalable quantum computer is presenting challenges in the field of engineering. It necessitates a microsystem operating at 4K in a dilution refrigerator, which would be inevitable to control thousands or millions of qubits sitting at 10mK. There have been IC implementations of pulse modulators generating qubit-controlling microwave signals [1– 4]. The pulse modulation based on direct synthesis demonstrated feasibility of driving multiple qubits with frequency-division multiplexing (FDM) through one RF cable [1 – 3]. The first implementation of a full controller [1], which includes both read and write chains for spin qubits, demonstrated the highest level of integration. However, the previous work used external local oscillator (LO) sources for frequency synthesis. External feeding of LO requires precise matching; otherwise, a failure would cause leakage to the qubit driving output through PCB traces, resulting in AC-Stark shift of qubit state by unwanted tones at near-resonance. It becomes more problematic in FDM-based multi-qubit driving. Since the fidelity of qubit operations strongly relies on the quality of driving frequency, a low-noise LO generation by a phase-locked loop (PLL) is one of the most important factors [5]. The internal generation of LO gives additional benefits in superconducting qubit interface. It necessitates multiple LOs since the superconducting qubit uses microwave pulse driving for both read and write. To detect the state of a qubit through dispersive readout, the phase reflected from the readout resonator should be measured. Therefore, the driving pulses for the read and the write should be synchronized to a single reference timing. Using built-in PLLs sharing a single reference clock naturally solves this problem.