Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2609.08569

Fabrication And Characterization Of High-Quality Nb/Al-AlO$_x$/Nb Cross-Type Josephson Tunnel Junctions Utilising CMP-based Planarisation Techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler, A. Fleischmann, C. Enss

Published Aug 26, 2026• 0 citations
arXivHTMLPDF

Abstract

Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlOx/Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO$_2$ to allow for planarisation of the structures and to ensure the reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that require a lot of time and potentially leave unwanted wings along the edges of microstructures behind that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO$_2$. This is not only much faster, but produces smooth and uniform surfaces, which in turn effectively improves the reliability of our JJ production process resulting in a high yield of over $90\,\%$ on wafer-scale. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to $1\,\mathrm{μm} \times 1\,\mathrm{μm}$ distributed across the wafer and extract the junction specific quality parameters from their IV-characteristics and their Fraunhofer patterns.

DOI
10.48550/arxiv.2609.08569

Related papers

Anodization-free fabrication process for high-quality cross-type Josephson tunnel junctions based on a Nb/Al-AlO x /Nb trilayer

F Adam, C. Enss, Sebastian Kempf

Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.

arXiv:2403.01806•Superconductor Science and Technology•Jul 8, 2024•5 citations

Towards Fabrication of Sub-Micrometer Cross-Type Aluminum Josephson Junctions

Stephan Mechold, Katja Peiselt, Matthias Schmelz +5 more

The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.

IEEE Transactions on Applied Superconductivity•Dec 18, 2023•2 citations

Sub-micrometer-sized, cross-type Nb–AlOx–Nb tunnel junctions with low parasitic capacitance

Solveig Anders, Matthias Schmelz, Ludwig Fritzsch +4 more

We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.

Superconductor Science and Technology•May 14, 2009•57 citations

Characterization of Superconducting Josephson Junctions on Electro-Optic LiNbO 3 Substrates at mK Temperatures

Saba Kousar, Roberta Satariano, G. Ausanio +5 more

We report on the fabrication and millikelvin char acterization of Nb/Al–AlOx/Nb Josephson junctions directly de posited on X-cut LiNbO3 substrates. Motivated by the strong electro-optic and piezoelectric properties of LiNbO3, such devices are of interest for future hybrid superconducting–electro-optic architectures. The junctions were fabricated using standard processes involving DC magnetron sputtering followed by controlled thermal oxidation of the aluminum layer to form an AlOx tunnel barrier with reproducible junction areas. Insulation of the junctions was achieved by anodization and SiOx deposition. Electrical measurements performed at 30 mK reveal high-quality Josephson tunnel junction behavior with a critical current density ofJc= 70 A/cm2and a characteristic voltage reaching values up toVm= 286 mV. Differential conductance measurements exhibit pronounced quasiparticle peaks corresponding to a sum gap energy of 2Δ = (2.73 ± 0.05) meV, confirming the good quality of the Nb electrodes. Magnetic-field-dependent measure ments yield a Josephson penetration depth of λJ= 45 μm, confirming operation in the small-junction regime, with deviations from the ideal Josephson interference pattern attributed to non-uniform current distribution across the junction area. Compared to our previous characterization at 4.2 K, this work demonstrates reliable Josephson junction operation on LiNbO3 at dilution-refrigerator temperatures relevant for quantum circuits, supporting the suitability of lithium niobate as a promising substrate for future hybrid superconducting–electro-optic device implementations.

IEEE Transactions on Applied Superconductivity•Feb 23, 2026•0 citations

Niobium and Aluminum Josephson Junctions Fabricated with a Damascene CMP Process

Abelaziz Ramzi, Serge A. Charlebois, Philip Krantz

We report on the fabrication of Josephson junction and superconducting bridges using a damascene CMP process applied for a first time to superconductors. The demonstrated industrial reliability of damascene CMP processes on large scale semiconductor circuits is a major incentive for our research that should allow large numbers of nanometric Josephson junctions to be fabricated in both Nb and Al, the two main material employed in superconducting quantum computing (qubit) and RSFQ electronics fabrication.We carried out a Chemical-Mechanical Polishing (CMP) process on Nb and Al films deposited on a SiO2 layer patterned with trenches of 100 to 300 nm of nominal depth. The process formed long bridges, 1 to 4 μm wide. The susceptibility and resistive transitions showed that CMP has no observable influence on superconductivity.We have also developed a hybrid technique that uses Al/Al2O3/Al shadow evaporation in the trenches before the damascene CMP process. This allows for high quality “in-situ” junction oxidation with the size reduction benefit provided by the damascene CMP process. We easily reach junctions sizes near 0.5 μm2 which are difficult to fabricate by other methods.We describe these techniques and report on measurements on large bridges and junctions and on the fabrication and measurements of Al and Nb nanobridges.

Physics Procedia•Jan 1, 2012•3 citations

Sub-$\mu\hbox{m}$ Josephson Junctions for Superconducting Quantum Devices

J. M. Meckbach, Michael Merker, Simon J. Buehler +7 more

For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.

arXiv:1210.1012•IEEE Transactions on Applied Superconductivity•Dec 4, 2012•11 citations
Fabrication And Characterization Of High-Quality Nb/Al-AlOx_xx​/Nb Cross-Type Josephson Tunnel Junctions Utilising CMP-based Planarisation Techniques
Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlOx/Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO2_22​ to allow for planarisation of the structures and to ensure the reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that require a lot of time and potentially leave unwanted wings along the edges of microstructures behind that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO2_22​. This is not only much faster, but produces smooth and uniform surfaces, which in turn effectively improves the reliability of our JJ production process resulting in a high yield of over 90 %90\,\%90% on wafer-scale. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 μm×1 μm1\,\mathrm{μm} \times 1\,\mathrm{μm}1μm×1μm distributed across the wafer and extract the junction specific quality parameters from their IV-characteristics and their Fraunhofer patterns.
Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.
We report on the fabrication and millikelvin char acterization of Nb/Al–AlOx/Nb Josephson junctions directly de posited on X-cut LiNbO3 substrates. Motivated by the strong electro-optic and piezoelectric properties of LiNbO3, such devices are of interest for future hybrid superconducting–electro-optic architectures. The junctions were fabricated using standard processes involving DC magnetron sputtering followed by controlled thermal oxidation of the aluminum layer to form an AlOx tunnel barrier with reproducible junction areas. Insulation of the junctions was achieved by anodization and SiOx deposition. Electrical measurements performed at 30 mK reveal high-quality Josephson tunnel junction behavior with a critical current density ofJc= 70 A/cm2and a characteristic voltage reaching values up toVm= 286 mV. Differential conductance measurements exhibit pronounced quasiparticle peaks corresponding to a sum gap energy of 2Δ = (2.73 ± 0.05) meV, confirming the good quality of the Nb electrodes. Magnetic-field-dependent measure ments yield a Josephson penetration depth of λJ= 45 μm, confirming operation in the small-junction regime, with deviations from the ideal Josephson interference pattern attributed to non-uniform current distribution across the junction area. Compared to our previous characterization at 4.2 K, this work demonstrates reliable Josephson junction operation on LiNbO3 at dilution-refrigerator temperatures relevant for quantum circuits, supporting the suitability of lithium niobate as a promising substrate for future hybrid superconducting–electro-optic device implementations.
We report on the fabrication of Josephson junction and superconducting bridges using a damascene CMP process applied for a first time to superconductors. The demonstrated industrial reliability of damascene CMP processes on large scale semiconductor circuits is a major incentive for our research that should allow large numbers of nanometric Josephson junctions to be fabricated in both Nb and Al, the two main material employed in superconducting quantum computing (qubit) and RSFQ electronics fabrication.We carried out a Chemical-Mechanical Polishing (CMP) process on Nb and Al films deposited on a SiO2 layer patterned with trenches of 100 to 300 nm of nominal depth. The process formed long bridges, 1 to 4 μm wide. The susceptibility and resistive transitions showed that CMP has no observable influence on superconductivity.We have also developed a hybrid technique that uses Al/Al2O3/Al shadow evaporation in the trenches before the damascene CMP process. This allows for high quality “in-situ” junction oxidation with the size reduction benefit provided by the damascene CMP process. We easily reach junctions sizes near 0.5 μm2 which are difficult to fabricate by other methods.We describe these techniques and report on measurements on large bridges and junctions and on the fabrication and measurements of Al and Nb nanobridges.
Sub-μm\mu\hbox{m}μm Josephson Junctions for Superconducting Quantum Devices
For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.