Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2403.01806 · Superconductor Science and Technology

Anodization-free fabrication process for high-quality cross-type Josephson tunnel junctions based on a Nb/Al-AlO x /Nb trilayer

F Adam, C. Enss, Sebastian Kempf

Published Jul 8, 2024• 5 citations
arXivHTMLPDF

Abstract

Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.

DOI
10.1088/1361-6668/ad59cf

Related papers

Fabrication And Characterization Of High-Quality Nb/Al-AlO$_x$/Nb Cross-Type Josephson Tunnel Junctions Utilising CMP-based Planarisation Techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler +2 more

Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlOx/Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO$_2$ to allow for planarisation of the structures and to ensure the reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that require a lot of time and potentially leave unwanted wings along the edges of microstructures behind that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO$_2$. This is not only much faster, but produces smooth and uniform surfaces, which in turn effectively improves the reliability of our JJ production process resulting in a high yield of over $90\,\%$ on wafer-scale. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to $1\,\mathrm{μm} \times 1\,\mathrm{μm}$ distributed across the wafer and extract the junction specific quality parameters from their IV-characteristics and their Fraunhofer patterns.

arXiv:2609.08569•Aug 26, 2026•0 citations

Fabrication of high-quality submicron Nb/Al-AlO x /Nb tunnel junctions

Haifeng Yu, Cao Wen-Hui, Zhu Xiao-Bo +6 more

Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.

Chinese Physics B•Aug 1, 2008•7 citations

Nb/AlOx/Nb trilayer process for the fabrication of submicron Josephson junctions and low-noise dc SQUIDs

Manjul Bhushan, E. M. Macedo

A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.

Applied Physics Letters•Mar 25, 1991•42 citations

Towards Fabrication of Sub-Micrometer Cross-Type Aluminum Josephson Junctions

Stephan Mechold, Katja Peiselt, Matthias Schmelz +5 more

The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.

IEEE Transactions on Applied Superconductivity•Dec 18, 2023•2 citations

Sub-micrometer-sized, cross-type Nb–AlOx–Nb tunnel junctions with low parasitic capacitance

Solveig Anders, Matthias Schmelz, Ludwig Fritzsch +4 more

We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.

Superconductor Science and Technology•May 14, 2009•57 citations

Fabrication Process for Deep Submicron SQUID Circuits with Three Independent Niobium Layers

Silke Wolter, Julian Linek, Josepha Altmann +6 more

We present a fabrication technology for nanoscale superconducting quantum interference devices (SQUIDs) with overdamped superconductor-normal metal-superconductor (SNS) trilayer Nb/HfTi/Nb Josephson junctions. A combination of electron-beam lithography with chemical-mechanical polishing and magnetron sputtering on thermally oxidized Si wafers is used to produce direct current SQUIDs with 100-nm-lateral dimensions for Nb lines and junctions. We extended the process from originally two to three independent Nb layers. This extension offers the possibility to realize superconducting vias to all Nb layers without the HfTi barrier, and hence to increase the density and complexity of circuit structures. We present results on the yield of this process and measurements of SQUID characteristics.

Micromachines•Mar 24, 2021•3 citations
Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.
Fabrication And Characterization Of High-Quality Nb/Al-AlOx_xx​/Nb Cross-Type Josephson Tunnel Junctions Utilising CMP-based Planarisation Techniques
Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlOx/Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO2_22​ to allow for planarisation of the structures and to ensure the reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that require a lot of time and potentially leave unwanted wings along the edges of microstructures behind that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO2_22​. This is not only much faster, but produces smooth and uniform surfaces, which in turn effectively improves the reliability of our JJ production process resulting in a high yield of over 90 %90\,\%90% on wafer-scale. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 μm×1 μm1\,\mathrm{μm} \times 1\,\mathrm{μm}1μm×1μm distributed across the wafer and extract the junction specific quality parameters from their IV-characteristics and their Fraunhofer patterns.
Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.
A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
We report on a technology for the fabrication of sub-micrometer sized cross-type Josephson tunnel junctions in niobium technology. We present the fabrication scheme and properties of cross-type junctions with linear dimensions from 10 down to 0.6 µm. Sidewall passivation of the junctions is achieved by anodization as well as by planarizing the junctions with SiO in a self-aligned deposition step. The measured ratio of the sub-gap resistance to the normal resistance is about 35. Because of their low sub-gap current and low parasitic capacitance such junctions are well suited for applications like high resolution SQUIDs.
We present a fabrication technology for nanoscale superconducting quantum interference devices (SQUIDs) with overdamped superconductor-normal metal-superconductor (SNS) trilayer Nb/HfTi/Nb Josephson junctions. A combination of electron-beam lithography with chemical-mechanical polishing and magnetron sputtering on thermally oxidized Si wafers is used to produce direct current SQUIDs with 100-nm-lateral dimensions for Nb lines and junctions. We extended the process from originally two to three independent Nb layers. This extension offers the possibility to realize superconducting vias to all Nb layers without the HfTi barrier, and hence to increase the density and complexity of circuit structures. We present results on the yield of this process and measurements of SQUID characteristics.