Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2504.16686 · Nanomaterials

Wafer-Scale Electrical Characterization of Al/AlxOy/Al Tunnel Junctions for Process Monitoring at Room Temperature

Simon Lang, I. Eisele, Johannes Weber, Alexandra Schewski, Emir Music, Alwin Maiwald, Martin Hahn, Daniela Zahn, Zhen Luo, L. Nebrich, Benedikt Schoof, Thomas Mayer, Leonhard Sturm-Rogon, Wilfried Lerch, Rui N. Pereira, Christoph Kutter

Published May 7, 2026• 3 citations
arXivHTMLPDF

Abstract

Josephson junctions are key elements in superconducting qubits. Their efficient wafer-scale characterization is crucial for process control and optimization, motivating analysis approaches that extend beyond conventional cryogenic measurements. In this work, we demonstrate that room temperature (RT) capacitance and current–voltage measurements, combined with appropriate data analysis, enable extraction of relevant junction parameters such as oxide thickness, tunnel coefficient, and interfacial defect density. Furthermore, different charge transport mechanisms can be identified from detailed current–voltage analysis. We evaluate our characterization technique using tunnel junctions fabricated on 200 mm wafers in a complementary metal–oxide–semiconductor (CMOS)-compatible subtractive process. The results show a homogeneous average oxide thickness across the wafer with a variation below 3%. A dependence of the tunnel coefficient on oxide thickness indicates a stoichiometry gradient within the oxide. Additionally, low interfacial defect densities in the range of 70–5000 defects/cm2 are observed in our junctions, increasing with decreasing oxide thickness, suggesting that wet etching used for thickness control introduces interfacial trap states. Our study highlights the importance of advanced RT characterization for extracting tunnel junction parameters on the wafer scale, enabling effective process monitoring and optimization in industrial superconducting qubit manufacturing.

DOI
10.3390/nano16100569

Related papers

Wafer-Scale Al Junction Technology for Superconducting Quantum Circuits

Matthias Schmelz, E. Mutsenik, S. Bravin +8 more

Josephson tunnel junctions represent a key element in superconducting electronics and quantum circuits. For many years, shadow evaporation by means of Dolan-type bridges has been the state-of-the-art for deep sub- micrometer sized structures. Increasing demand in the number of Josephson junctions, e.g. in qubit circuits and travelling wave parametric amplifiers, requests for a wafer-scale fabrication process with precise control of junction parameters and have led to an advanced lift-off technique called Manhattan-type junction technology in recent years. Herein, we report on the development of a 100 mm wafer-scale fabrication technology for deep sub-micrometer sized Al Josephson junctions with linear dimensions down to 180 nm. The critical currentICof the junctions ranges from about 10 to 120 nA scaling with their linear dimensions. Low temperature transport measurements as well as room-temperature characterization has been used forICand process homogeneity determination of series arrays of up to 50 Josephson junctions. We discuss technology parameters such as yield, on-chip and on-wafer reproducibility of the junction's critical currents as well as main process limitations. Moreover, we present experimental results on the characterization of first transmon-type qubits fabricated using this technology.

IEEE Transactions on Applied Superconductivity•Feb 9, 2024•8 citations

Fabrication and characterization of high-quality Nb/Al-AlO x /Nb cross-type Josephson tunnel junctions utilising CMP-based planarisation techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler +2 more

Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.

arXiv:2609.08569•Superconductor Science and Technology•Nov 10, 2026•0 citations

Aluminum Josephson Junction Formation on 200mm Wafers Using Different Oxidation Techniques

Simon Lang, Alexandra Schewski, I. Eisele +2 more

This work focuses on the manufacturing of Al/AlOx/Al Josephson junctions (JJs), which are essential components of many quantum circuits. Two processes were studied to understand the oxidation of the aluminum surface. Static oxidation was performed by removing native AlOx in a cluster system with Ar-ion beam milling and controlling the final tunneling oxide by applying a specific O2 pressure in the chamber. Controlled plasma oxidation was performed by removing native AlOx with a H2 plasma followed by a defined reoxidation with an oxygen plasma. The resulting oxides had thicknesses up to 10 nm and their electrical properties were analyzed on wafer level, providing insight into the structure and composition of the aluminum oxides and their applicability for Qubits. This work is crucial for reliable industrial manufacturing on full-scale 200 mm wafers with a very high uniformity level.

ECS Transactions•May 19, 2023•5 citations

Improving wafer-scale Josephson junction resistance variation in superconducting quantum coherent circuits

John Mark Kreikebaum, Kevin P. O’Brien, Alexis Morvan +1 more

Abstract Quantum bits, or qubits, are an example of coherent circuits envisioned for next-generation computers and detectors. A robust superconducting qubit with a coherent lifetime of O(100 µs) is the transmon: a Josephson junction functioning as a non-linear inductor shunted with a capacitor to form an anharmonic oscillator. In a complex device with many such transmons, precise control over each qubit frequency is often required, and thus variations of the junction area and tunnel barrier thickness must be sufficiently minimized to achieve optimal performance while avoiding spectral overlap between neighboring circuits. Simply transplanting our recipe optimized for single, stand-alone devices to wafer-scale (producing 64, 1x1 cm dies from a 150 mm wafer) initially resulted in global drifts in room-temperature tunneling resistance of ± 30%. Inferring a critical current I c variation from this resistance distribution, we present an optimized process developed from a systematic 38 wafer study that results in < 3.5% relative standard deviation (RSD) in critical current ( ≡ σ I c / I c ) for 3000 Josephson junctions (both single-junctions and asymmetric SQUIDs) across an area of 49 cm2. Looking within a 1x1 cm moving window across the substrate gives an estimate of the variation characteristic of a given qubit chip. Our best process, utilizing ultrasonically assisted development, uniform ashing, and dynamic oxidation has shown σ I c / I c = 1.8% within 1x1 cm, on average, with a few 1x1 cm areas having σ I c / I c < 1.0% (equivalent to σ f / f < 0.5%). Such stability would drastically improve the yield of multi-junction chips with strict critical current requirements.

arXiv:1909.09165•Superconductor Science and Technology•Apr 29, 2020•145 citations

Fabrication and I-V Characterization of an Al/AlO x /Al Josephson Junction for Superconducting Qubits

Gustavo Moreto, Diego Molina, Everton Arrighi +1 more

Josephson junctions are key devices in circuit quantum electrodynamics (cQED) and play a central role in quantum technologies. Among the different types, superconductor-insulator-superconductor (S-I-S) junctions based on aluminum/aluminum oxide/aluminum stacks are widely used in superconducting qubits. Despite being a well-established topic, Josephson junctions still present a rich variety of physical regimes and behaviors that require careful experimental investigation. In this work, we present the fabrication of a Dolan-type Josephson junction and its current-voltage (I-V) characterization process. The fabricated devices exhibit good process reproducibility, with approximately 90% yield and a room-temperature resistance variation of about 10% between junctions. The measured I-V curves show nonlinear behavior and hysteresis, consistent with an underdamped regime, while also displaying signatures of phase diffusion. Key parameters such as the normal-state resistance, quasiparticle resistance, critical current, and superconducting gap voltage are extracted and show good agreement with the Ambegaokar-Baratoff relation. The measurement setup and filtering scheme used for the characterization are also described.

Symposium on Microelectronics Technology and Devices•Aug 1, 2026•0 citations

Improvements of the Single Angle Overlap Josephson Junction Technology for Qubit Application

Muhammad Shoaib, Valentina Di Meo, C. Barone +6 more

We develop a fully complementary metal-oxide semiconductor (CMOS) fabrication technique for the realization of a superconducting qubit network (SQN). In our current research work, we focus on a single-angle overlap Josephson junction fabrication technique, based on the lift-off process for defining both base and top electrodes, avoiding the wiring insulator layer and requiring an RF Ar etching process before AlOxbarrier growth. The fabricated Al/AlOx/Al microscale Josephson junctions have been tested at low temperature (T = 300 mK) in the superconducting state using current–voltage characteristic measurements.

IEEE Transactions on Applied Superconductivity•Mar 30, 2026•0 citations
Josephson junctions are key elements in superconducting qubits. Their efficient wafer-scale characterization is crucial for process control and optimization, motivating analysis approaches that extend beyond conventional cryogenic measurements. In this work, we demonstrate that room temperature (RT) capacitance and current–voltage measurements, combined with appropriate data analysis, enable extraction of relevant junction parameters such as oxide thickness, tunnel coefficient, and interfacial defect density. Furthermore, different charge transport mechanisms can be identified from detailed current–voltage analysis. We evaluate our characterization technique using tunnel junctions fabricated on 200 mm wafers in a complementary metal–oxide–semiconductor (CMOS)-compatible subtractive process. The results show a homogeneous average oxide thickness across the wafer with a variation below 3%. A dependence of the tunnel coefficient on oxide thickness indicates a stoichiometry gradient within the oxide. Additionally, low interfacial defect densities in the range of 70–5000 defects/cm2 are observed in our junctions, increasing with decreasing oxide thickness, suggesting that wet etching used for thickness control introduces interfacial trap states. Our study highlights the importance of advanced RT characterization for extracting tunnel junction parameters on the wafer scale, enabling effective process monitoring and optimization in industrial superconducting qubit manufacturing.
Josephson tunnel junctions represent a key element in superconducting electronics and quantum circuits. For many years, shadow evaporation by means of Dolan-type bridges has been the state-of-the-art for deep sub- micrometer sized structures. Increasing demand in the number of Josephson junctions, e.g. in qubit circuits and travelling wave parametric amplifiers, requests for a wafer-scale fabrication process with precise control of junction parameters and have led to an advanced lift-off technique called Manhattan-type junction technology in recent years. Herein, we report on the development of a 100 mm wafer-scale fabrication technology for deep sub-micrometer sized Al Josephson junctions with linear dimensions down to 180 nm. The critical currentICof the junctions ranges from about 10 to 120 nA scaling with their linear dimensions. Low temperature transport measurements as well as room-temperature characterization has been used forICand process homogeneity determination of series arrays of up to 50 Josephson junctions. We discuss technology parameters such as yield, on-chip and on-wafer reproducibility of the junction's critical currents as well as main process limitations. Moreover, we present experimental results on the characterization of first transmon-type qubits fabricated using this technology.
Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.
This work focuses on the manufacturing of Al/AlOx/Al Josephson junctions (JJs), which are essential components of many quantum circuits. Two processes were studied to understand the oxidation of the aluminum surface. Static oxidation was performed by removing native AlOx in a cluster system with Ar-ion beam milling and controlling the final tunneling oxide by applying a specific O2 pressure in the chamber. Controlled plasma oxidation was performed by removing native AlOx with a H2 plasma followed by a defined reoxidation with an oxygen plasma. The resulting oxides had thicknesses up to 10 nm and their electrical properties were analyzed on wafer level, providing insight into the structure and composition of the aluminum oxides and their applicability for Qubits. This work is crucial for reliable industrial manufacturing on full-scale 200 mm wafers with a very high uniformity level.
Abstract Quantum bits, or qubits, are an example of coherent circuits envisioned for next-generation computers and detectors. A robust superconducting qubit with a coherent lifetime of O(100 µs) is the transmon: a Josephson junction functioning as a non-linear inductor shunted with a capacitor to form an anharmonic oscillator. In a complex device with many such transmons, precise control over each qubit frequency is often required, and thus variations of the junction area and tunnel barrier thickness must be sufficiently minimized to achieve optimal performance while avoiding spectral overlap between neighboring circuits. Simply transplanting our recipe optimized for single, stand-alone devices to wafer-scale (producing 64, 1x1 cm dies from a 150 mm wafer) initially resulted in global drifts in room-temperature tunneling resistance of ± 30%. Inferring a critical current I c variation from this resistance distribution, we present an optimized process developed from a systematic 38 wafer study that results in < 3.5% relative standard deviation (RSD) in critical current ( ≡ σ I c / I c ) for 3000 Josephson junctions (both single-junctions and asymmetric SQUIDs) across an area of 49 cm2. Looking within a 1x1 cm moving window across the substrate gives an estimate of the variation characteristic of a given qubit chip. Our best process, utilizing ultrasonically assisted development, uniform ashing, and dynamic oxidation has shown σ I c / I c = 1.8% within 1x1 cm, on average, with a few 1x1 cm areas having σ I c / I c < 1.0% (equivalent to σ f / f < 0.5%). Such stability would drastically improve the yield of multi-junction chips with strict critical current requirements.
Josephson junctions are key devices in circuit quantum electrodynamics (cQED) and play a central role in quantum technologies. Among the different types, superconductor-insulator-superconductor (S-I-S) junctions based on aluminum/aluminum oxide/aluminum stacks are widely used in superconducting qubits. Despite being a well-established topic, Josephson junctions still present a rich variety of physical regimes and behaviors that require careful experimental investigation. In this work, we present the fabrication of a Dolan-type Josephson junction and its current-voltage (I-V) characterization process. The fabricated devices exhibit good process reproducibility, with approximately 90% yield and a room-temperature resistance variation of about 10% between junctions. The measured I-V curves show nonlinear behavior and hysteresis, consistent with an underdamped regime, while also displaying signatures of phase diffusion. Key parameters such as the normal-state resistance, quasiparticle resistance, critical current, and superconducting gap voltage are extracted and show good agreement with the Ambegaokar-Baratoff relation. The measurement setup and filtering scheme used for the characterization are also described.
We develop a fully complementary metal-oxide semiconductor (CMOS) fabrication technique for the realization of a superconducting qubit network (SQN). In our current research work, we focus on a single-angle overlap Josephson junction fabrication technique, based on the lift-off process for defining both base and top electrodes, avoiding the wiring insulator layer and requiring an RF Ar etching process before AlOxbarrier growth. The fabricated Al/AlOx/Al microscale Josephson junctions have been tested at low temperature (T = 300 mK) in the superconducting state using current–voltage characteristic measurements.