Wafer-Scale Al Junction Technology for Superconducting Quantum Circuits
Matthias Schmelz, E. Mutsenik, S. Bravin, A. Sh. Sultanov, Mario Ziegler, Uwe Hübner, Katja Peiselt, Stephan Mechold, G. Oelsner, J. Kunert, Ronny Stolz
Josephson tunnel junctions represent a key element in superconducting electronics and quantum circuits. For many years, shadow evaporation by means of Dolan-type bridges has been the state-of-the-art for deep sub- micrometer sized structures. Increasing demand in the number of Josephson junctions, e.g. in qubit circuits and travelling wave parametric amplifiers, requests for a wafer-scale fabrication process with precise control of junction parameters and have led to an advanced lift-off technique called Manhattan-type junction technology in recent years. Herein, we report on the development of a 100 mm wafer-scale fabrication technology for deep sub-micrometer sized Al Josephson junctions with linear dimensions down to 180 nm. The critical currentICof the junctions ranges from about 10 to 120 nA scaling with their linear dimensions. Low temperature transport measurements as well as room-temperature characterization has been used forICand process homogeneity determination of series arrays of up to 50 Josephson junctions. We discuss technology parameters such as yield, on-chip and on-wafer reproducibility of the junction's critical currents as well as main process limitations. Moreover, we present experimental results on the characterization of first transmon-type qubits fabricated using this technology.
Josephson tunnel junctions represent a key element in superconducting electronics and quantum circuits. For many years, shadow evaporation by means of Dolan-type bridges has been the state-of-the-art for deep sub- micrometer sized structures. Increasing demand in the number of Josephson junctions, e.g. in qubit circuits and travelling wave parametric amplifiers, requests for a wafer-scale fabrication process with precise control of junction parameters and have led to an advanced lift-off technique called Manhattan-type junction technology in recent years. Herein, we report on the development of a 100 mm wafer-scale fabrication technology for deep sub-micrometer sized Al Josephson junctions with linear dimensions down to 180 nm. The critical currentICof the junctions ranges from about 10 to 120 nA scaling with their linear dimensions. Low temperature transport measurements as well as room-temperature characterization has been used forICand process homogeneity determination of series arrays of up to 50 Josephson junctions. We discuss technology parameters such as yield, on-chip and on-wafer reproducibility of the junction's critical currents as well as main process limitations. Moreover, we present experimental results on the characterization of first transmon-type qubits fabricated using this technology.
In the upcoming decades quantum technologies, especially quantum computation, will have a strong influence on industrial, technological, economic, and social progress and are, therefore, considered to be one of the key technologies. The fundamental building blocks for quantum computation are quantum bits (qubits). The superconducting platform offers one of the most promising implementations due to its monolithic character and potential for scalability. Present research around the world primarily focusses on scaling up the number of qubits, so reliable wafer-scale fabrication technologies are mandatory. In this paper, we present our recent developments on wafer-scale fabrication of superconducting quantum circuits including Josephson junctions by the Manhattan-type technology. We discuss fabrication parameters as well as electrical characterization. For arrays out of 50 Josephson junctions with structure dimensions of 200 nm × 200 nm, we achieve a critical current standard deviation of approx. 3% on-chip and 7% on-wafer. We also show first measurement results of so fabricated transmon-type qubits with relaxation and decoherence times ofT1= 12.5 µs andT2= 15.0 µs, respectively. With an increasing number of superconducting qubits and, thus, their input and read-out lines, new challenges arise: Crosstalk between qubits, unwanted modes in the qubit environment, and required interconnections. One way to counteract is the implementation of low inductance connections across coplanar waveguides. This can be realized by aluminum air bridges. In this paper we discuss the air bridges’ fabrication parameters and the impact on the integrated circuits’ elements, e.g., Josephson junctions. We show electrical and superconducting measurements with critical temperatures and critical currents ofTc> 1.0 K andIc> 0.6 mA, respectively.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
Josephson tunnel junctions are the centerpiece of almost any superconducting electronic circuit, including qubits. Typically, the junctions for qubits are fabricated using shadow evaporation techniques to reduce dielectric loss contributions from the superconducting film interfaces. In recent years, however, sub-micrometer scale overlap junctions have started to attract attention. Compared to shadow mask techniques, neither an angle dependent deposition nor free-standing bridges or overlaps are needed, which are significant limitations for wafer-scale processing. This comes at the cost of breaking the vacuum during fabrication, but simplifies integration in multi-layered circuits and implementation of vastly different junction sizes and enables fabrication on a larger scale in an industrially standardized process. In this work, we demonstrate the feasibility of a subtractive process for the fabrication of overlap junctions. In an array of test contacts, we find low aging of the average normal state resistance of only 1.6% over 6 months. We evaluate the coherence properties of the junctions by employing them in superconducting transmon qubits. In time domain experiments, we find that both, the qubit life- and coherence time of our best device, are, on average, greater than 20 μs. Finally, we discuss potential improvements to our technique. This work paves the way toward a more standardized process flow with advanced materials and growth processes, and constitutes an important step for the large scale fabrication of superconducting quantum circuits.
Josephson junctions are key elements in superconducting qubits. Their efficient wafer-scale characterization is crucial for process control and optimization, motivating analysis approaches that extend beyond conventional cryogenic measurements. In this work, we demonstrate that room temperature (RT) capacitance and current–voltage measurements, combined with appropriate data analysis, enable extraction of relevant junction parameters such as oxide thickness, tunnel coefficient, and interfacial defect density. Furthermore, different charge transport mechanisms can be identified from detailed current–voltage analysis. We evaluate our characterization technique using tunnel junctions fabricated on 200 mm wafers in a complementary metal–oxide–semiconductor (CMOS)-compatible subtractive process. The results show a homogeneous average oxide thickness across the wafer with a variation below 3%. A dependence of the tunnel coefficient on oxide thickness indicates a stoichiometry gradient within the oxide. Additionally, low interfacial defect densities in the range of 70–5000 defects/cm2 are observed in our junctions, increasing with decreasing oxide thickness, suggesting that wet etching used for thickness control introduces interfacial trap states. Our study highlights the importance of advanced RT characterization for extracting tunnel junction parameters on the wafer scale, enabling effective process monitoring and optimization in industrial superconducting qubit manufacturing.
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.
The most commonly used physical realization of superconducting qubits for quantum circuits is a transmon. There are a number of superconducting quantum circuits applications, where Josephson junction critical current reproducibility over a chip is crucial. Here, we report on a robust chip scale Al/AlOx/Al junctions fabrication method due to comprehensive study of shadow evaporation and oxidation steps. We experimentally demonstrate the evidence of optimal Josephson junction electrodes thickness, deposition rate and deposition angle, which ensure minimal electrode surface and line edge roughness. The influence of oxidation method, pressure and time on critical current reproducibility is determined. With the proposed method we demonstrate Al/AlOx/Al junction fabrication with the critical current variation (σ/Ic) less than 3.9% (from 150×200 to 150×600nm2 area) and 7.7% (for 100×100nm2 area) over 20×20mm2 chip. Finally, we fabricate separately three 5×10mm2 chips with 18 transmon qubits (near 4.3 GHz frequency) showing less than 1.9% frequency variation between qubit on different chips. The proposed approach and optimization criteria can be utilized for a robust wafer-scale superconducting qubit circuits fabrication.