Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Planarized multi-layer fabrication technology for LTS large-scale SFQ circuits

Shuichi Nagasawa, K. Hinode, Masao Sugita, T. Satoh, Hiroyuki Akaike, Yoshihiro Kitagawa, Mutsuo Hidaka

Published Nov 7, 2003• 29 citations
Publisher

Abstract

We have been developing a 10 kA cm −2 Nb advanced fabrication process to make larger scale and higher speed SFQ circuits that have over 100k junctions. The main challenges in implementing this process are related to increasing the critical current density of junctions, decreasing design rules and increasing the number of Nb layers. We have proposed a planarized multi-layer structure, which consists of a Nb/AlO x /Nb junction layer, Nb wiring layers, Nb shield layers, a Nb layer for dc power, a Nb ground plane, SiO 2 insulator layers and a Mo resistor layer. In fabricating this multi-layer structure, we have developed a new planarization technology which enables the flattening of the SiO 2 insulator surface over the Nb wiring layer independent of the pattern sizes of the Nb wirings. This planarization technology consists of SiO 2 bias sputtering, reactive ion etching with a reversal mask of the Nb wiring and mechanical polishing planarization. The SEM photographs showed excellent flatness for the planarized multi-layer structure.

DOI
10.1088/0953-2048/16/12/036

Related papers

Fabrication Process of Planarized Multi-Layer Nb Integrated Circuits

T. Satoh, K. Hinode, Hiroyuki Akaike +3 more

To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•42 citations

Planarization Process for Fabricating Multi-Layer Nb Integrated Circuits Incorporating Top Active Layer

T. Satoh, K. Hinode, Shuichi Nagasawa +7 more

We have developed an advanced process for fabricating a next-generation multi-layer Nb integrated circuit structure incorporating a top active layer. In this structure, the passive-transmission-line (PTL) layer is placed between the top active layer and a DC-bias current layer at the bottom. This structure will make it possible to flexibly design active circuits and PTL wiring, and will also enable active circuits to be effectively shielded from magnetic fields generated by a large DC-bias current. Both the DC-bias current layer and the PTL layer are planarized; however, the top active layer is fabricated without planarization. To fabricate this new structure, it was necessary to achieve a better planarization process for junctions formed over underlying Nb patterns. The combined process we developed comprising additional SiO2deposition and additional mechanical polishing after the standard Caldera planarization process results in superior planarization for junction formation. We obtained excellent characteristics of junctions formed over underlying pattern edges when they were fabricated on surfaces planarized using this new process. Using the process, we fabricated new 10-Nb-layer integrated circuit structures and estimated the characteristics of their circuit elements.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•16 citations

A double-active-layer NB-based fabrication process for superconducting digital integrated circuits

Mingfan Chen, Shucheng Yang, Liliang Ying +7 more

Abstract We present SIMIT-Nb08, an eight-layer Nb-based fabrication process for double-active-layer single-flux-quantum (SFQ) digital circuits, aimed at overcoming the routing congestion and integration ‘density wall’ of planar SFQ designs. Both Nb/Al–AlO x /Nb JJ layers were designed with the same nominal critical current density of J c = 6 kA cm −2 , and the measured values were 6.15 and 6.26 kA cm −2 for the lower and upper JJ layers, respectively. This architecture incorporates a dual-ground-plane structure to reduce interlayer electromagnetic coupling and shield stray magnetic flux generated by bias lines. A stop-on-metal chemical mechanical polishing module was implemented to provide a controlled dielectric thickness and a planar surface for upper-layer device fabrication. We validate a double-layer SFQ logic cell library with wide DC bias margins on both layers, and demonstrate ultra-high-speed dynamic operation via a toggle flip-flop-based frequency-divider test exceeding 100 GHz. In addition, the process and cross-layer interconnect reliability are demonstrated by functional operation of a cross-layer one-bit full adder and an eight-bit shift register (SR), where the SR exhibits an effective junction-density improvement of ∼4× over typical single-layer implementations. Post-route benchmarking on a 320-cell SR indicates that SIMIT-Nb08 delivers substantial improvements in power, performance, and area, including a 32.2% reduction in area, a 25.0% increase in maximum operating frequency ( f max ), and a 65.3% reduction in estimated power compared with SIMIT-Nb03 (29.9%, 6.3%, and 62.5%, respectively, compared with SIMIT-Nb04), indicating its potential for routing-constrained SFQ digital circuits.

Superconductor Science and Technology•Sep 30, 2026•0 citations

Development of 15kA/cm$^2$ Fabrication Process for Superconducting Integrated Digital Circuits

Liliang Ying, Xue Zhang, Guixiang He +7 more

A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 $Ω$, followed by the deposition of Nb/Al-AlO$_x$/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm$^2$. To increase the Al-AlO$_x$ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.

arXiv:2304.01588•Apr 4, 2023•0 citations

Development of Multi-Layer Fabrication Process for SFQ Large Scale Integrated Digital Circuits

Liliang Ying, Xue Zhang, Minghui Niu +4 more

We have developed a fabrication technology for superconducting integrated circuits with Nb-based Josephson junctions. The standard fabrication process with 10 mask levels includes 3 Nb superconducting layers and a Mo resistor layer. The influence of deposition parameters on film stress, electrical properties, and surface roughness were studied systematically. High quality Nb, Al, Mo, and SiO2films were successfully deposited for the subsequent fabrication of circuits. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistanceRshof 2 Ω, followed by the deposition of Nb/Al-AlOx/Nb trilayer Josephson-junction. The target critical current densityJcwas set at 6 kA/cm2. Small-scale circuits such as our standard library cells have been successfully fabricated and tested, confirming the capability of our fabrication technology for superconducting integrated circuits.

arXiv:2011.06272•IEEE Transactions on Applied Superconductivity•Mar 11, 2021•76 citations

Current status and future prospect of the Nb-based fabrication process for single flux quantum circuits

Mutsuo Hidaka, Shuichi Nagasawa, T. Satoh +2 more

The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.

Superconductor Science and Technology•Feb 15, 2006•62 citations
We have been developing a 10 kA cm −2 Nb advanced fabrication process to make larger scale and higher speed SFQ circuits that have over 100k junctions. The main challenges in implementing this process are related to increasing the critical current density of junctions, decreasing design rules and increasing the number of Nb layers. We have proposed a planarized multi-layer structure, which consists of a Nb/AlO x /Nb junction layer, Nb wiring layers, Nb shield layers, a Nb layer for dc power, a Nb ground plane, SiO 2 insulator layers and a Mo resistor layer. In fabricating this multi-layer structure, we have developed a new planarization technology which enables the flattening of the SiO 2 insulator surface over the Nb wiring layer independent of the pattern sizes of the Nb wirings. This planarization technology consists of SiO 2 bias sputtering, reactive ion etching with a reversal mask of the Nb wiring and mechanical polishing planarization. The SEM photographs showed excellent flatness for the planarized multi-layer structure.
To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.
We have developed an advanced process for fabricating a next-generation multi-layer Nb integrated circuit structure incorporating a top active layer. In this structure, the passive-transmission-line (PTL) layer is placed between the top active layer and a DC-bias current layer at the bottom. This structure will make it possible to flexibly design active circuits and PTL wiring, and will also enable active circuits to be effectively shielded from magnetic fields generated by a large DC-bias current. Both the DC-bias current layer and the PTL layer are planarized; however, the top active layer is fabricated without planarization. To fabricate this new structure, it was necessary to achieve a better planarization process for junctions formed over underlying Nb patterns. The combined process we developed comprising additional SiO2deposition and additional mechanical polishing after the standard Caldera planarization process results in superior planarization for junction formation. We obtained excellent characteristics of junctions formed over underlying pattern edges when they were fabricated on surfaces planarized using this new process. Using the process, we fabricated new 10-Nb-layer integrated circuit structures and estimated the characteristics of their circuit elements.
Abstract We present SIMIT-Nb08, an eight-layer Nb-based fabrication process for double-active-layer single-flux-quantum (SFQ) digital circuits, aimed at overcoming the routing congestion and integration ‘density wall’ of planar SFQ designs. Both Nb/Al–AlO x /Nb JJ layers were designed with the same nominal critical current density of J c = 6 kA cm −2 , and the measured values were 6.15 and 6.26 kA cm −2 for the lower and upper JJ layers, respectively. This architecture incorporates a dual-ground-plane structure to reduce interlayer electromagnetic coupling and shield stray magnetic flux generated by bias lines. A stop-on-metal chemical mechanical polishing module was implemented to provide a controlled dielectric thickness and a planar surface for upper-layer device fabrication. We validate a double-layer SFQ logic cell library with wide DC bias margins on both layers, and demonstrate ultra-high-speed dynamic operation via a toggle flip-flop-based frequency-divider test exceeding 100 GHz. In addition, the process and cross-layer interconnect reliability are demonstrated by functional operation of a cross-layer one-bit full adder and an eight-bit shift register (SR), where the SR exhibits an effective junction-density improvement of ∼4× over typical single-layer implementations. Post-route benchmarking on a 320-cell SR indicates that SIMIT-Nb08 delivers substantial improvements in power, performance, and area, including a 32.2% reduction in area, a 25.0% increase in maximum operating frequency ( f max ), and a 65.3% reduction in estimated power compared with SIMIT-Nb03 (29.9%, 6.3%, and 62.5%, respectively, compared with SIMIT-Nb04), indicating its potential for routing-constrained SFQ digital circuits.
Development of 15kA/cm2^22 Fabrication Process for Superconducting Integrated Digital Circuits
A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 ΩΩΩ, followed by the deposition of Nb/Al-AlOx_xx​/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm2^22. To increase the Al-AlOx_xx​ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.
We have developed a fabrication technology for superconducting integrated circuits with Nb-based Josephson junctions. The standard fabrication process with 10 mask levels includes 3 Nb superconducting layers and a Mo resistor layer. The influence of deposition parameters on film stress, electrical properties, and surface roughness were studied systematically. High quality Nb, Al, Mo, and SiO2films were successfully deposited for the subsequent fabrication of circuits. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistanceRshof 2 Ω, followed by the deposition of Nb/Al-AlOx/Nb trilayer Josephson-junction. The target critical current densityJcwas set at 6 kA/cm2. Small-scale circuits such as our standard library cells have been successfully fabricated and tested, confirming the capability of our fabrication technology for superconducting integrated circuits.
The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.