Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Fabrication Process of Planarized Multi-Layer Nb Integrated Circuits

T. Satoh, K. Hinode, Hiroyuki Akaike, Shuichi Nagasawa, Y. Kitagawa, Mutsuo Hidaka

Published Jun 1, 2005• 42 citations
Publisher

Abstract

To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.

DOI
10.1109/tasc.2005.849698

Related papers

Planarized multi-layer fabrication technology for LTS large-scale SFQ circuits

Shuichi Nagasawa, K. Hinode, Masao Sugita +4 more

We have been developing a 10 kA cm −2 Nb advanced fabrication process to make larger scale and higher speed SFQ circuits that have over 100k junctions. The main challenges in implementing this process are related to increasing the critical current density of junctions, decreasing design rules and increasing the number of Nb layers. We have proposed a planarized multi-layer structure, which consists of a Nb/AlO x /Nb junction layer, Nb wiring layers, Nb shield layers, a Nb layer for dc power, a Nb ground plane, SiO 2 insulator layers and a Mo resistor layer. In fabricating this multi-layer structure, we have developed a new planarization technology which enables the flattening of the SiO 2 insulator surface over the Nb wiring layer independent of the pattern sizes of the Nb wirings. This planarization technology consists of SiO 2 bias sputtering, reactive ion etching with a reversal mask of the Nb wiring and mechanical polishing planarization. The SEM photographs showed excellent flatness for the planarized multi-layer structure.

Superconductor Science and Technology•Nov 7, 2003•29 citations

Planarization Process for Fabricating Multi-Layer Nb Integrated Circuits Incorporating Top Active Layer

T. Satoh, K. Hinode, Shuichi Nagasawa +7 more

We have developed an advanced process for fabricating a next-generation multi-layer Nb integrated circuit structure incorporating a top active layer. In this structure, the passive-transmission-line (PTL) layer is placed between the top active layer and a DC-bias current layer at the bottom. This structure will make it possible to flexibly design active circuits and PTL wiring, and will also enable active circuits to be effectively shielded from magnetic fields generated by a large DC-bias current. Both the DC-bias current layer and the PTL layer are planarized; however, the top active layer is fabricated without planarization. To fabricate this new structure, it was necessary to achieve a better planarization process for junctions formed over underlying Nb patterns. The combined process we developed comprising additional SiO2deposition and additional mechanical polishing after the standard Caldera planarization process results in superior planarization for junction formation. We obtained excellent characteristics of junctions formed over underlying pattern edges when they were fabricated on surfaces planarized using this new process. Using the process, we fabricated new 10-Nb-layer integrated circuit structures and estimated the characteristics of their circuit elements.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•16 citations

Planarized Process for Single-Flux-Quantum Circuits With Self-Shunted Nb/Nb$_{x}$Si$_{1-x}$/Nb Josephson Junctions

David I. Olaya, Manuel A. Castellanos-Beltran, Javier F. Pulecio +6 more

We describe our process for fabricating single-flux-quantum circuits for applications in communications metrology, advanced computing, and quantum information. The process flow includes four superconducting metal layers, one junction layer, one palladium-gold bias resistor layer, and a contact pad layer. Planarization using chemical-mechanical polishing is performed on the two lower insulating layers. This process is based on Josephson junctions with niobium superconducting electrodes and self-shunted, amorphous niobium-doped silicon barriers on the insulating side near the metal-insulator transition. The barrier material is deposited by cosputtering silicon and niobium, with the junction properties controlled by the relative sputtering powers and the duration of the barrier deposition step. The profiles of the deposition rates across 3-in (76.2 mm) wafers give a corresponding radial profile of the critical current density Jcthat increases by ~46% from the center to the edge of the wafer. To characterize our process, we have measured and show data for niobium metal quality and its magnetic penetration depth, as well as for wire and via inductances, and for via critical currents. The uniformity of the junction critical current Icacross a wafer was measured on test chips with 2.7-μm-diameter junctions. Within a 5 mm × 5 mm area, the standard deviation of Icwas ~2% for chips near the center of the wafer and up to ~7% for chips near the edge. We also describe process improvements and innovations under development aimed at increasing circuit density and high-speed performance.

IEEE Transactions on Applied Superconductivity•Mar 16, 2019•26 citations

Planarized Nb 4-Layer Fabrication Process for Superconducting Integrated Circuits and Its Fabricated Device Evaluation

Shuichi Nagasawa, Masamitsu Tanaka, Naoki Takeuchi +13 more

We developed a Nb 4-layer process for fabricating superconducting integrated circuits that involves using caldera planarization to increase the flexibility and reliability of the fabrication process. We call this process the planarized high-speed standard process (PHSTP). Planarization enables us to flexibly adjust most of the Nb and SiO2 film thicknesses; we can select reduced film thicknesses to obtain larger mutual coupling depending on the application. It also reduces the risk of intra-layer shorts due to etching residues at the step-edge regions. We describe the detailed process flows of the planarization for the Josephson junction layer and the evaluation of devices fabricated with PHSTP. The results indicated no short defects or degradation in junction characteristics and good agreement between designed and measured inductances and resistances. We also developed single-flux-quantum (SFQ) and adiabatic quantum-flux-parametron (AQFP) logic cell libraries and tested circuits fabricated with PHSTP. We found that the designed circuits operated correctly. The SFQ shift-registers fabricated using PHSTP showed a high yield. Numerical simulation results indicate that the AQFP gates with increased mutual coupling by the planarized layer structure increase the maximum interconnect length between gates.

IEICE Transactions on Electronics•Mar 16, 2021•6 citations

Current status and future prospect of the Nb-based fabrication process for single flux quantum circuits

Mutsuo Hidaka, Shuichi Nagasawa, T. Satoh +2 more

The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.

Superconductor Science and Technology•Feb 15, 2006•62 citations

Development of 15kA/cm$^2$ Fabrication Process for Superconducting Integrated Digital Circuits

Liliang Ying, Xue Zhang, Guixiang He +7 more

A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 $Ω$, followed by the deposition of Nb/Al-AlO$_x$/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm$^2$. To increase the Al-AlO$_x$ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.

arXiv:2304.01588•Apr 4, 2023•0 citations
To improve the operating speed and density of Nb single-flux-quantum integrated circuits, we developed an advanced fabrication process based on NEC's standard process. We fabricated planarized six-Nb-layer circuit structures using this advanced process. This new structure has four Nb wiring layers for greater design flexibility. To shield the magnetic field produced by the DC bias current, the DC bias power supply layer was placed under the groundplane. The critical current density of the Josephson junction was 10 kA/cm/sup 2/. We fabricated and tested more than 10 wafers and demonstrated that the six-layer circuits were successfully planarized. We also confirmed insulation between each Nb layer and the reliability of superconducting contacts. This planarization did not significantly degrade the junction characteristics. We measured small spreads in the critical current of less than 2%. These results demonstrated the effectiveness of this advanced process based on mechanical-polishing planarization.
We have been developing a 10 kA cm −2 Nb advanced fabrication process to make larger scale and higher speed SFQ circuits that have over 100k junctions. The main challenges in implementing this process are related to increasing the critical current density of junctions, decreasing design rules and increasing the number of Nb layers. We have proposed a planarized multi-layer structure, which consists of a Nb/AlO x /Nb junction layer, Nb wiring layers, Nb shield layers, a Nb layer for dc power, a Nb ground plane, SiO 2 insulator layers and a Mo resistor layer. In fabricating this multi-layer structure, we have developed a new planarization technology which enables the flattening of the SiO 2 insulator surface over the Nb wiring layer independent of the pattern sizes of the Nb wirings. This planarization technology consists of SiO 2 bias sputtering, reactive ion etching with a reversal mask of the Nb wiring and mechanical polishing planarization. The SEM photographs showed excellent flatness for the planarized multi-layer structure.
We have developed an advanced process for fabricating a next-generation multi-layer Nb integrated circuit structure incorporating a top active layer. In this structure, the passive-transmission-line (PTL) layer is placed between the top active layer and a DC-bias current layer at the bottom. This structure will make it possible to flexibly design active circuits and PTL wiring, and will also enable active circuits to be effectively shielded from magnetic fields generated by a large DC-bias current. Both the DC-bias current layer and the PTL layer are planarized; however, the top active layer is fabricated without planarization. To fabricate this new structure, it was necessary to achieve a better planarization process for junctions formed over underlying Nb patterns. The combined process we developed comprising additional SiO2deposition and additional mechanical polishing after the standard Caldera planarization process results in superior planarization for junction formation. We obtained excellent characteristics of junctions formed over underlying pattern edges when they were fabricated on surfaces planarized using this new process. Using the process, we fabricated new 10-Nb-layer integrated circuit structures and estimated the characteristics of their circuit elements.
Planarized Process for Single-Flux-Quantum Circuits With Self-Shunted Nb/Nbx_{x}x​Si1−x_{1-x}1−x​/Nb Josephson Junctions
We describe our process for fabricating single-flux-quantum circuits for applications in communications metrology, advanced computing, and quantum information. The process flow includes four superconducting metal layers, one junction layer, one palladium-gold bias resistor layer, and a contact pad layer. Planarization using chemical-mechanical polishing is performed on the two lower insulating layers. This process is based on Josephson junctions with niobium superconducting electrodes and self-shunted, amorphous niobium-doped silicon barriers on the insulating side near the metal-insulator transition. The barrier material is deposited by cosputtering silicon and niobium, with the junction properties controlled by the relative sputtering powers and the duration of the barrier deposition step. The profiles of the deposition rates across 3-in (76.2 mm) wafers give a corresponding radial profile of the critical current density Jcthat increases by ~46% from the center to the edge of the wafer. To characterize our process, we have measured and show data for niobium metal quality and its magnetic penetration depth, as well as for wire and via inductances, and for via critical currents. The uniformity of the junction critical current Icacross a wafer was measured on test chips with 2.7-μm-diameter junctions. Within a 5 mm × 5 mm area, the standard deviation of Icwas ~2% for chips near the center of the wafer and up to ~7% for chips near the edge. We also describe process improvements and innovations under development aimed at increasing circuit density and high-speed performance.
We developed a Nb 4-layer process for fabricating superconducting integrated circuits that involves using caldera planarization to increase the flexibility and reliability of the fabrication process. We call this process the planarized high-speed standard process (PHSTP). Planarization enables us to flexibly adjust most of the Nb and SiO2 film thicknesses; we can select reduced film thicknesses to obtain larger mutual coupling depending on the application. It also reduces the risk of intra-layer shorts due to etching residues at the step-edge regions. We describe the detailed process flows of the planarization for the Josephson junction layer and the evaluation of devices fabricated with PHSTP. The results indicated no short defects or degradation in junction characteristics and good agreement between designed and measured inductances and resistances. We also developed single-flux-quantum (SFQ) and adiabatic quantum-flux-parametron (AQFP) logic cell libraries and tested circuits fabricated with PHSTP. We found that the designed circuits operated correctly. The SFQ shift-registers fabricated using PHSTP showed a high yield. Numerical simulation results indicate that the AQFP gates with increased mutual coupling by the planarized layer structure increase the maximum interconnect length between gates.
The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.
Development of 15kA/cm2^22 Fabrication Process for Superconducting Integrated Digital Circuits
A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 ΩΩΩ, followed by the deposition of Nb/Al-AlOx_xx​/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm2^22. To increase the Al-AlOx_xx​ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.