Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1705.08993 · Applied Physics Letters

Overlap junctions for high coherence superconducting qubits

Xian Wu, J. L. Long, H. S. Ku, Russell E. Lake, Mustafa Bal, David P. Pappas

Published Jul 17, 2017• 49 citations
arXivHTMLPDF

Abstract

Fabrication of sub-micron Josephson junctions is demonstrated using standard processing techniques for high-coherence, superconducting qubits. These junctions are made in two separate lithography steps with normal-angle evaporation. Most significantly, this work demonstrates that it is possible to achieve high coherence with junctions formed on aluminum surfaces cleaned in situ with Ar milling before the junction oxidation. This method eliminates the angle-dependent shadow masks typically used for small junctions. Therefore, this is conducive to the implementation of typical methods for improving margins and yield using conventional CMOS processing. The current method uses electron-beam lithography and an additive process to define the top and bottom electrodes. Extension of this work to optical lithography and subtractive processes is discussed.

DOI
10.1063/1.4993937

Related papers

Coherent superconducting qubits from a subtractive junction fabrication process

Alexander Stehli, Jan David Brehm, Tim Wolz +6 more

Josephson tunnel junctions are the centerpiece of almost any superconducting electronic circuit, including qubits. Typically, the junctions for qubits are fabricated using shadow evaporation techniques to reduce dielectric loss contributions from the superconducting film interfaces. In recent years, however, sub-micrometer scale overlap junctions have started to attract attention. Compared to shadow mask techniques, neither an angle dependent deposition nor free-standing bridges or overlaps are needed, which are significant limitations for wafer-scale processing. This comes at the cost of breaking the vacuum during fabrication, but simplifies integration in multi-layered circuits and implementation of vastly different junction sizes and enables fabrication on a larger scale in an industrially standardized process. In this work, we demonstrate the feasibility of a subtractive process for the fabrication of overlap junctions. In an array of test contacts, we find low aging of the average normal state resistance of only 1.6% over 6 months. We evaluate the coherence properties of the junctions by employing them in superconducting transmon qubits. In time domain experiments, we find that both, the qubit life- and coherence time of our best device, are, on average, greater than 20 μs. Finally, we discuss potential improvements to our technique. This work paves the way toward a more standardized process flow with advanced materials and growth processes, and constitutes an important step for the large scale fabrication of superconducting quantum circuits.

arXiv:2006.16862•Applied Physics Letters•Sep 21, 2020•34 citations

Improvements of the Single Angle Overlap Josephson Junction Technology for Qubit Application

Muhammad Shoaib, Valentina Di Meo, C. Barone +6 more

We develop a fully complementary metal-oxide semiconductor (CMOS) fabrication technique for the realization of a superconducting qubit network (SQN). In our current research work, we focus on a single-angle overlap Josephson junction fabrication technique, based on the lift-off process for defining both base and top electrodes, avoiding the wiring insulator layer and requiring an RF Ar etching process before AlOxbarrier growth. The fabricated Al/AlOx/Al microscale Josephson junctions have been tested at low temperature (T = 300 mK) in the superconducting state using current–voltage characteristic measurements.

IEEE Transactions on Applied Superconductivity•Mar 30, 2026•0 citations

Native-oxide-passivated trilayer junctions for superconducting qubits

Pankaj Sethi, Om Prakash, Jukka-Pekka Kaikkonen +15 more

Superconducting qubits in today's quantum processing units are typically fabricated with angle-evaporated aluminum--aluminum-oxide--aluminum Josephson junctions. However, there is an urgent need to overcome the limited reproducibility of this approach when scaling up the number of qubits and junctions. Fabrication methods based on subtractive patterning of superconductor--insulator--superconductor trilayers, used for more classical large-scale Josephson junction circuits, could provide the solution but they in turn often suffer from lossy dielectrics incompatible with high qubit coherence. In this work, we utilize native aluminum oxide as a sidewall passivation layer for junctions based on aluminum--aluminum-oxide--niobium trilayers, and use such junctions in qubits. We design the fabrication process such that the few-nanometer-thin native oxide is not exposed to oxide removal steps that could increase its defect density or hinder its ability to prevent shorting between the leads of the junction. With these junctions, we design and fabricate transmon-like qubits and measure time-averaged coherence times up to 30 $μ$s at a qubit frequency of 5 GHz, corresponding to a qubit quality factor of one million. Our process uses subtractive patterning and optical lithography on wafer scale, enabling high throughput in patterning. This approach provides a scalable path toward fabrication of superconducting qubits on industry-standard platforms.

arXiv:2504.03481•Physical Review Applied•Nov 26, 2025•2 citations

Aluminum hard mask technique for the fabrication of high quality submicron Nb/Al–AlOx/Nb Josephson junctions

Ch Kaiser, J M Meckbach, K S Ilin +4 more

We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.

arXiv:1009.0167•Superconductor Science and Technology•Dec 23, 2010•16 citations

Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits

Amr Osman, J. Simon, Andreas Bengtsson +7 more

We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.

arXiv:2011.05230•Applied Physics Letters•Feb 8, 2021•87 citations

CMOS compatible fabrication methodsfor submicron Josephson junction qubits

A. Potts, G.J. Parker, J.J. Baumberg +1 more

The authors have developed two distinct processes for the fabrication of mesoscopic Josephson junction qubits that are compatible with conventional CMOS processing. These devices, based on superconducting Al/Al2O3/Al tunnel junctions, are fabricated by electron beam lithography using single-layer and multi-layer resists. The new single-layer resist process is found to have significant advantages over conventional fabrication methods using suspended tri-layer shadow masks. It is simpler and more accurate to implement, and avoids the significant areas of redundant metallisation that are an unavoidable by-product of the tri-layer shadow mask method.

IEE Proceedings - Science Measurement and Technology•Sep 5, 2001•38 citations
Fabrication of sub-micron Josephson junctions is demonstrated using standard processing techniques for high-coherence, superconducting qubits. These junctions are made in two separate lithography steps with normal-angle evaporation. Most significantly, this work demonstrates that it is possible to achieve high coherence with junctions formed on aluminum surfaces cleaned in situ with Ar milling before the junction oxidation. This method eliminates the angle-dependent shadow masks typically used for small junctions. Therefore, this is conducive to the implementation of typical methods for improving margins and yield using conventional CMOS processing. The current method uses electron-beam lithography and an additive process to define the top and bottom electrodes. Extension of this work to optical lithography and subtractive processes is discussed.
Josephson tunnel junctions are the centerpiece of almost any superconducting electronic circuit, including qubits. Typically, the junctions for qubits are fabricated using shadow evaporation techniques to reduce dielectric loss contributions from the superconducting film interfaces. In recent years, however, sub-micrometer scale overlap junctions have started to attract attention. Compared to shadow mask techniques, neither an angle dependent deposition nor free-standing bridges or overlaps are needed, which are significant limitations for wafer-scale processing. This comes at the cost of breaking the vacuum during fabrication, but simplifies integration in multi-layered circuits and implementation of vastly different junction sizes and enables fabrication on a larger scale in an industrially standardized process. In this work, we demonstrate the feasibility of a subtractive process for the fabrication of overlap junctions. In an array of test contacts, we find low aging of the average normal state resistance of only 1.6% over 6 months. We evaluate the coherence properties of the junctions by employing them in superconducting transmon qubits. In time domain experiments, we find that both, the qubit life- and coherence time of our best device, are, on average, greater than 20 μs. Finally, we discuss potential improvements to our technique. This work paves the way toward a more standardized process flow with advanced materials and growth processes, and constitutes an important step for the large scale fabrication of superconducting quantum circuits.
We develop a fully complementary metal-oxide semiconductor (CMOS) fabrication technique for the realization of a superconducting qubit network (SQN). In our current research work, we focus on a single-angle overlap Josephson junction fabrication technique, based on the lift-off process for defining both base and top electrodes, avoiding the wiring insulator layer and requiring an RF Ar etching process before AlOxbarrier growth. The fabricated Al/AlOx/Al microscale Josephson junctions have been tested at low temperature (T = 300 mK) in the superconducting state using current–voltage characteristic measurements.
Superconducting qubits in today's quantum processing units are typically fabricated with angle-evaporated aluminum--aluminum-oxide--aluminum Josephson junctions. However, there is an urgent need to overcome the limited reproducibility of this approach when scaling up the number of qubits and junctions. Fabrication methods based on subtractive patterning of superconductor--insulator--superconductor trilayers, used for more classical large-scale Josephson junction circuits, could provide the solution but they in turn often suffer from lossy dielectrics incompatible with high qubit coherence. In this work, we utilize native aluminum oxide as a sidewall passivation layer for junctions based on aluminum--aluminum-oxide--niobium trilayers, and use such junctions in qubits. We design the fabrication process such that the few-nanometer-thin native oxide is not exposed to oxide removal steps that could increase its defect density or hinder its ability to prevent shorting between the leads of the junction. With these junctions, we design and fabricate transmon-like qubits and measure time-averaged coherence times up to 30 μμμs at a qubit frequency of 5 GHz, corresponding to a qubit quality factor of one million. Our process uses subtractive patterning and optical lithography on wafer scale, enabling high throughput in patterning. This approach provides a scalable path toward fabrication of superconducting qubits on industry-standard platforms.
We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.
The authors have developed two distinct processes for the fabrication of mesoscopic Josephson junction qubits that are compatible with conventional CMOS processing. These devices, based on superconducting Al/Al2O3/Al tunnel junctions, are fabricated by electron beam lithography using single-layer and multi-layer resists. The new single-layer resist process is found to have significant advantages over conventional fabrication methods using suspended tri-layer shadow masks. It is simpler and more accurate to implement, and avoids the significant areas of redundant metallisation that are an unavoidable by-product of the tri-layer shadow mask method.