Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Analysis of superconducting analog-to-digital converter front-end for improved resolution and large dynamic range

Pascal Febvre, Héla Gassara, Patricia Desgreys, Patrick Loumeau

Published Apr 25, 2010• 0 citations
OpenAlex

Abstract

Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).

Related papers

Superconductor analog-to-digital converters and their applications

Deepnarayan Gupta, Amol Inamdar, Dmitri E. Kirichenko +2 more

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

IEEE MTT-S International Microwave Symposium digest•Jun 1, 2011•23 citations

The Testing of Superconductive ADCs in a Software-Defined Radio Base Stations

Abhishek Arun, Hans G. Kerkhoff, Marcel H.H. Weusthof

Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external

•Nov 29, 2001•1 citation

Superconductor analog-to-digital converters

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +1 more

Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.

Proceedings of the IEEE•Sep 20, 2004•182 citations

Superconductor analog to digital converter for sigint applications

Amol Inamdar, Deepnarayan Gupta, Timur V. Filippov +6 more

Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.

IEEE Military Communications Conference (MILCOM)•Nov 1, 2008•9 citations

High-Resolution Analog-to-Digital Converters toward Software-Defined-Radio Receivers

Akira Fujimaki

We describe three types of software-defined-radio (SDR) receivers based on superconducting technologies. The superconducting analog bandpass filters are essential for all types of the receivers. Another key component is an analog-to-digital converters (ADCs), which are required to have high resolution with a broad band width. The complementary A ADC based on the single-flux-quantum circuit is a promising candidate for the SDR receivers because it has a practical nature together with above-mentioned requirements. The experimentally obtained signal-to-noise ratio (SNR) and sensitivity, which are closely related to the resolution, are 34 dB and 20 μA for a quarter of the full-scale input with a band width of about 20 MHz. If we use the optimum decimation filter, the ADC is expected to have the SNR of 82 dB and the sensitivity of 300 nA. These values meet the requirements of the easiest type of the SDR receiver. After new fabrication process has been introduced and the architecture of the ADC has been improved, all types of recievers could be realized based on suoerconductors.

IEICE Transactions on Electronics•Feb 1, 2006•4 citations

Flux quantum sigma-delta analog-to-digital converters for rf signals

Donald L. Miller, John X. Przybysz, A. Hodge Worsham +1 more

The sigma-delta architecture is the method of choice for analog-to-digital converters (ADCs) for high dynamic range applications. This architecture uses oversampling and precise feedback to generate a shaped spectral distribution of the quantization noise. Subsequent digital filtering suppresses out-of-band quantization noise, yielding a large signal to in-band noise ratio. A unique advantage of superconducting electronics is the availability of the flux quantum to provide quantum mechanically accurate feedback at GHz rates. Josephson digital technology extends sigma-delta ADCs from MHz sampling rates to GHz sampling rates, from kHz signal bandwidths to MHz signal bandwidths, with comparable or better dynamic range when compared to semiconductor implementations. This paper presents circuits for Josephson sigma-delta ADCs, including single-loop and double-loop modulators operating at sampling rates up to 2 GHz, and circuits for quantized feedback. The first demonstration of double-loop noise shaping is also presented.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•25 citations
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.
Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external
Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.
Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.
We describe three types of software-defined-radio (SDR) receivers based on superconducting technologies. The superconducting analog bandpass filters are essential for all types of the receivers. Another key component is an analog-to-digital converters (ADCs), which are required to have high resolution with a broad band width. The complementary A ADC based on the single-flux-quantum circuit is a promising candidate for the SDR receivers because it has a practical nature together with above-mentioned requirements. The experimentally obtained signal-to-noise ratio (SNR) and sensitivity, which are closely related to the resolution, are 34 dB and 20 μA for a quarter of the full-scale input with a band width of about 20 MHz. If we use the optimum decimation filter, the ADC is expected to have the SNR of 82 dB and the sensitivity of 300 nA. These values meet the requirements of the easiest type of the SDR receiver. After new fabrication process has been introduced and the architecture of the ADC has been improved, all types of recievers could be realized based on suoerconductors.
The sigma-delta architecture is the method of choice for analog-to-digital converters (ADCs) for high dynamic range applications. This architecture uses oversampling and precise feedback to generate a shaped spectral distribution of the quantization noise. Subsequent digital filtering suppresses out-of-band quantization noise, yielding a large signal to in-band noise ratio. A unique advantage of superconducting electronics is the availability of the flux quantum to provide quantum mechanically accurate feedback at GHz rates. Josephson digital technology extends sigma-delta ADCs from MHz sampling rates to GHz sampling rates, from kHz signal bandwidths to MHz signal bandwidths, with comparable or better dynamic range when compared to semiconductor implementations. This paper presents circuits for Josephson sigma-delta ADCs, including single-loop and double-loop modulators operating at sampling rates up to 2 GHz, and circuits for quantized feedback. The first demonstration of double-loop noise shaping is also presented.