Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Photonics Research

Superconducting nanowire single-photon detector array with pixel-level photon-number resolution

Chenrui Wang, Chaomeng Ding, Jingxue Chen, Yuchi Li, Jia Huang, Hongxin Xu, Xiaoyu Liu, Lixing YOU, Hao Li

Published Aug 28, 2026• 0 citations
Publisher

Abstract

We report a 16-pixel (4×4) superconducting nanowire single-photon detector (SNSPD) array featuring pixel-level photon-number-resolving capability. This multidimensional sensing is enabled by integrating a compact four-element series nanowire architecture into each spatial pixel, allowing direct discrimination of one to four photons. Under single-mode fiber illumination, the device achieves a total system detection efficiency of 41.5%, given the array geometrical fill factor of 53%. Across all channels, the device exhibits reliable multiphoton discrimination, maintaining minimum readout fidelities of 96%, 89%, 73%, and 77% for one- to four-photon states, respectively. Furthermore, independent channel evaluations reveal low timing jitter and negligible inter-channel crosstalk (<0.1 % ). By implementing differentiating pulse shaping for high-flux operation, a maximum single-channel −3 dB count rate of 984 MHz is achieved, establishing an aggregated array bandwidth potential of 8.9 GHz. This sensing architecture may provide a viable pathway toward high-flux single-photon imaging, offering potential applications in quantum optics and light detection and ranging (LiDAR) systems.

DOI
10.1364/prj.609048

Related papers

Enhanced Detection Rate and High Photon-Number Efficiencies with a Scalable Parallel SNSPD

Lorenzo Stasi, Towsif Taher, Giovanni V. Resta +3 more

Since their inception, superconducting nanowire single-photon detectors have been enabling quantum optical applications and the rise of the photonic quantum industry. The evolution in the detector design and read-out strategies has led to the introduction of devices with a plurality of independent pixels, which have been able to operate with high system detection efficiency at high speed while also supporting photon number resolution capabilities. However, this comes at the cost of a complex readout that requires one coaxial cable for each pixel of the array. Here, we report a 28-pixel SNSPD with a dedicated parallel architecture that, while maintaining a simple readout with a single coaxial line, enables the detector to operate at high speed with low-performance degradation. The device shows a maximum single-photon efficiency of 88% and is able to maintain its efficiency above 50%, coupled with a timing jitter lower than 80 ps, up to a detection rate of 200 million counts per second. The detector also provides state-of-the-art photon-number-resolving performances with a 2-photon efficiency of 75% and a 3-photon efficiency of 62%.

arXiv:2406.15312•ACS Photonics•Dec 17, 2024•26 citations

Polarization resolving and imaging with a single-photon sensitive superconducting nanowire array

Xing-Qu Sun, Weijun Zhang, Chengjun Zhang +7 more

Superconducting nanowire single-photon detectors (SNSPDs) have attracted remarkable interest for visible and near-infrared single-photon detection due to their outstanding performance. However, conventional SNSPDs are generally used as binary photon-counting detectors. Another important characteristic of light, i.e., polarization, which can provide additional information of the object, has not been resolved using the standalone SNSPD. In this work, we present a first prototype of the polarimeter based on a four-pixel superconducting nanowire array, capable of resolving the polarization state of linearly-polarized light at the single-photon level. The detector array design is based on a division of focal plane configuration in which the orientation of each nanowire division (pixel) is offset by 45°. Each single nanowire pixel operates as a combination of a photon detector and almost linear polarization filter, with an average polarization extinction ratio of ∼10. The total system detection efficiency of the array is ∼1% at a total dark count rate of 680 cps, with a timing jitter of 126 ps, when the detector array is free-space coupled and illuminated with 1550-nm photons. The mean errors of the measured angle of polarization and degree of linear polarization were about -3° and 0.12, respectively. Furthermore, we successfully demonstrated polarization imaging at low-light level using the proposed detector. Our results pave the way for the development of a single-photon sensitive, fast, and large-scale integrated polarization polarimeter or imager. Such detector may find promising application in photon-starved polarization resolving and imaging with high spatial and temporal resolution.

Optics Express•Mar 18, 2021•30 citations

Sixteen-channel fiber array-coupled superconducting single-photon detector array with average system detection efficiency over 60% at telecom wavelength

Weijun Zhang, Guangzhao Xu, Lixing You +8 more

We report a compact, scalable, and high-performance superconducting nanowire single-photon detector (SNSPD) array by using a multichannel optical fiber array-coupled configuration. For single pixels with an active area of 18 µm in diameter and illuminated at the telecom wavelength of 1550 nm, we achieved a pixel yield of 13/16 on one chip, an average system detection efficiency of 69% at a dark count rate of 160 cps, a minimum timing jitter of 74 ps, and a maximum count rate of ∼ 40 M c p s . The optical crosstalk coefficient between adjacent channels is better than − 60 d B . The performance of the fiber array-coupled detectors is comparable with a standalone detector coupled to a single fiber. Our method is promising for the development of scalable, high-performance, and high-yield SNSPDs.

arXiv:2101.01556•Optics Letters•Jan 28, 2021•7 citations

Scalable implementation of a superconducting nanowire single-photon detector array with a superconducting digital signal processor

Masahiro Yabuno, Shigeyuki Miyajima, Shigehito Miki +1 more

A two-dimensional single-photon imaging system with high sensitivity and high time resolution is the ultimate camera and useful in a wide range of fields. A superconducting nanowire single-photon detector (SSPD or SNSPD) is one of the best candidates for realizing such an ultimate camera due to its high detection efficiency in a wide spectral range, low dark count rate without after-pulsing, and excellent time resolution. Here we propose a new readout scheme to realize a large-scale imaging array based on SSPD, where a row-column readout architecture is combined with a digital signal processor based on a single-flux-quantum (SFQ) circuit. A 16-pixel row-column readout SSPD array is fabricated and measured with an SFQ digital signal processor. We successfully acquired spatial information as encoded digital bit codes with the temporal information of the photon detection. The system timing jitter was measured as <80 ps for all 16 pixels even through the SFQ signal processor, indicating the potential for an imaging array with an extremely high time resolution.

Optics Express•Apr 1, 2020•40 citations

Gigahertz Detection Rates and Dynamic Photon-Number Resolution with Superconducting Nanowire Arrays

Giovanni V. Resta, Lorenzo Stasi, Matthieu Perrenoud +5 more

Superconducting nanowire single-photon detectors (SNSPDs) have enabled the realization of several quantum optics technologies thanks to their high system detection efficiency (SDE), low dark counts, and fast recovery time. However, the widespread use of linear optical quantum computing, quasi-deterministic single-photon sources, and quantum repeaters requires even faster detectors that can also distinguish between different photon-number states. Here, we present an SNSPD array composed of 14 independent pixels, achieving an SDE of 90% in the telecommunications band. By reading each pixel of the array independently, we show detection of telecommunication photons at 1.5 GHz with 45% absolute SDE. We exploit the dynamic photon-number resolution of the array to demonstrate accurate state reconstruction for a wide range of light inputs, including operation with long-duration light pulses, as obtained with some cavity-based sources. We show two-photon and three-photon fidelities of 74% and 57%, respectively, which represent state-of-the-art results for fiber-coupled SNSPDs.

arXiv:2303.17401•Nano Letters•Jun 23, 2023•55 citations

A 16-Pixel Interleaved Superconducting Nanowire Single-Photon Detector Array With A Maximum Count Rate Exceeding 1.5 GHz

Weijun Zhang, Jia Huang, Chengjun Zhang +6 more

Increasing the count rate (CR) is one of the key issues in the development of superconducting nanowire single-photon detectors (SNSPDs) for different applications. This study aims to design, fabricate, and analyze a 16-pixel interleaved nanowire SNSPD array, which exhibits a system detection efficiency (SDE) of 72% and a dark CR of 100 Hz at a low-photon-flux limit and a wavelength of 1550 nm. By exploiting the increased pixel number and reduced dead time (10photons/s. Moreover, the SNSPD achieved a photon number resolution of up to 16 photons.

IEEE Transactions on Applied Superconductivity•Feb 9, 2019•95 citations
We report a 16-pixel (4×4) superconducting nanowire single-photon detector (SNSPD) array featuring pixel-level photon-number-resolving capability. This multidimensional sensing is enabled by integrating a compact four-element series nanowire architecture into each spatial pixel, allowing direct discrimination of one to four photons. Under single-mode fiber illumination, the device achieves a total system detection efficiency of 41.5%, given the array geometrical fill factor of 53%. Across all channels, the device exhibits reliable multiphoton discrimination, maintaining minimum readout fidelities of 96%, 89%, 73%, and 77% for one- to four-photon states, respectively. Furthermore, independent channel evaluations reveal low timing jitter and negligible inter-channel crosstalk (<0.1 % ). By implementing differentiating pulse shaping for high-flux operation, a maximum single-channel −3 dB count rate of 984 MHz is achieved, establishing an aggregated array bandwidth potential of 8.9 GHz. This sensing architecture may provide a viable pathway toward high-flux single-photon imaging, offering potential applications in quantum optics and light detection and ranging (LiDAR) systems.
Since their inception, superconducting nanowire single-photon detectors have been enabling quantum optical applications and the rise of the photonic quantum industry. The evolution in the detector design and read-out strategies has led to the introduction of devices with a plurality of independent pixels, which have been able to operate with high system detection efficiency at high speed while also supporting photon number resolution capabilities. However, this comes at the cost of a complex readout that requires one coaxial cable for each pixel of the array. Here, we report a 28-pixel SNSPD with a dedicated parallel architecture that, while maintaining a simple readout with a single coaxial line, enables the detector to operate at high speed with low-performance degradation. The device shows a maximum single-photon efficiency of 88% and is able to maintain its efficiency above 50%, coupled with a timing jitter lower than 80 ps, up to a detection rate of 200 million counts per second. The detector also provides state-of-the-art photon-number-resolving performances with a 2-photon efficiency of 75% and a 3-photon efficiency of 62%.
Superconducting nanowire single-photon detectors (SNSPDs) have attracted remarkable interest for visible and near-infrared single-photon detection due to their outstanding performance. However, conventional SNSPDs are generally used as binary photon-counting detectors. Another important characteristic of light, i.e., polarization, which can provide additional information of the object, has not been resolved using the standalone SNSPD. In this work, we present a first prototype of the polarimeter based on a four-pixel superconducting nanowire array, capable of resolving the polarization state of linearly-polarized light at the single-photon level. The detector array design is based on a division of focal plane configuration in which the orientation of each nanowire division (pixel) is offset by 45°. Each single nanowire pixel operates as a combination of a photon detector and almost linear polarization filter, with an average polarization extinction ratio of ∼10. The total system detection efficiency of the array is ∼1% at a total dark count rate of 680 cps, with a timing jitter of 126 ps, when the detector array is free-space coupled and illuminated with 1550-nm photons. The mean errors of the measured angle of polarization and degree of linear polarization were about -3° and 0.12, respectively. Furthermore, we successfully demonstrated polarization imaging at low-light level using the proposed detector. Our results pave the way for the development of a single-photon sensitive, fast, and large-scale integrated polarization polarimeter or imager. Such detector may find promising application in photon-starved polarization resolving and imaging with high spatial and temporal resolution.
We report a compact, scalable, and high-performance superconducting nanowire single-photon detector (SNSPD) array by using a multichannel optical fiber array-coupled configuration. For single pixels with an active area of 18 µm in diameter and illuminated at the telecom wavelength of 1550 nm, we achieved a pixel yield of 13/16 on one chip, an average system detection efficiency of 69% at a dark count rate of 160 cps, a minimum timing jitter of 74 ps, and a maximum count rate of ∼ 40 M c p s . The optical crosstalk coefficient between adjacent channels is better than − 60 d B . The performance of the fiber array-coupled detectors is comparable with a standalone detector coupled to a single fiber. Our method is promising for the development of scalable, high-performance, and high-yield SNSPDs.
A two-dimensional single-photon imaging system with high sensitivity and high time resolution is the ultimate camera and useful in a wide range of fields. A superconducting nanowire single-photon detector (SSPD or SNSPD) is one of the best candidates for realizing such an ultimate camera due to its high detection efficiency in a wide spectral range, low dark count rate without after-pulsing, and excellent time resolution. Here we propose a new readout scheme to realize a large-scale imaging array based on SSPD, where a row-column readout architecture is combined with a digital signal processor based on a single-flux-quantum (SFQ) circuit. A 16-pixel row-column readout SSPD array is fabricated and measured with an SFQ digital signal processor. We successfully acquired spatial information as encoded digital bit codes with the temporal information of the photon detection. The system timing jitter was measured as <80 ps for all 16 pixels even through the SFQ signal processor, indicating the potential for an imaging array with an extremely high time resolution.
Superconducting nanowire single-photon detectors (SNSPDs) have enabled the realization of several quantum optics technologies thanks to their high system detection efficiency (SDE), low dark counts, and fast recovery time. However, the widespread use of linear optical quantum computing, quasi-deterministic single-photon sources, and quantum repeaters requires even faster detectors that can also distinguish between different photon-number states. Here, we present an SNSPD array composed of 14 independent pixels, achieving an SDE of 90% in the telecommunications band. By reading each pixel of the array independently, we show detection of telecommunication photons at 1.5 GHz with 45% absolute SDE. We exploit the dynamic photon-number resolution of the array to demonstrate accurate state reconstruction for a wide range of light inputs, including operation with long-duration light pulses, as obtained with some cavity-based sources. We show two-photon and three-photon fidelities of 74% and 57%, respectively, which represent state-of-the-art results for fiber-coupled SNSPDs.
Increasing the count rate (CR) is one of the key issues in the development of superconducting nanowire single-photon detectors (SNSPDs) for different applications. This study aims to design, fabricate, and analyze a 16-pixel interleaved nanowire SNSPD array, which exhibits a system detection efficiency (SDE) of 72% and a dark CR of 100 Hz at a low-photon-flux limit and a wavelength of 1550 nm. By exploiting the increased pixel number and reduced dead time (10photons/s. Moreover, the SNSPD achieved a photon number resolution of up to 16 photons.