We present a Rapid Single Flux Quantum (RSFQ) microwave controller for superconducting qubits. Applying microwaves from room temperature sources is the conventional approach to excite quantum state transitions. Finding a method to apply short microwave bursts with a narrow linewidth is a challenge for on-chip Josephson based oscillators. We present a scheme containing an RSFQ pulse generator, ultra narrowband filter, SQUID based resonator and coupler. The operating frequency of the designed controller is 3-6 GHz. The unique feature of this design is a SQUID based resonator. By varying magnetic field in the SQUID, the\nresonance length can be varied between λ/4 and λ/2. The\nresonator is added as a shunt between the filter and coupler. Transmission of microwave signals from the filter to the output is determined by the shunt resonance. RSFQ T flip-flop circuit is designed to control the magnetic field applied to the SQUID in the resonator. Miniaturization of the coupler of 2-10 GHz has been done using a quasi-lumped element designed. We present the simulations results for the frequency response of\ndifferent resonance lengths of the modulator.
We present a Rapid Single Flux Quantum (RSFQ) microwave controller for superconducting qubits. Applying microwaves from room temperature sources is the conventional approach to excite quantum state transitions. Finding a method to apply short microwave bursts with a narrow linewidth is a challenge for on-chip Josephson based oscillators. We present a scheme containing an RSFQ pulse generator, ultra narrowband filter, SQUID based resonator and coupler. The operating frequency of the designed controller is 3-6 GHz. The unique feature of this design is a SQUID based resonator. By varying magnetic field in the SQUID, the\nresonance length can be varied between λ/4 and λ/2. The\nresonator is added as a shunt between the filter and coupler. Transmission of microwave signals from the filter to the output is determined by the shunt resonance. RSFQ T flip-flop circuit is designed to control the magnetic field applied to the SQUID in the resonator. Miniaturization of the coupler of 2-10 GHz has been done using a quasi-lumped element designed. We present the simulations results for the frequency response of\ndifferent resonance lengths of the modulator.
An on-chip superconducting microwave pulse generator (MPG), incorporating rapid single-flux-quantum (RSFQ) logic gates and passive radio frequency (RF) components, is an energy-efficient solution for controlling superconducting quantum bits (qubits). Traditional RSFQ MPG designs, however, suffer from a large footprint as multiple RF components (including impedance matching networks, filters, etc.) are separately implemented one after another. In this Letter, we propose a compact on-chip MPG by introducing an integrated RF module. Using a generalized filter synthesis technique, the integrated RF module combines the functionalities of impedance matching and bandpass filtering as a single inductor-capacitor (LC) lumped network. Plenty of circuit elements can, thus, be saved, and the resultant LC network is applicable to both real and complex terminal impedance cases. For validation, a superconducting MPG adopting a fourth-order, 5 GHz centered, 100 MHz bandwidth integrated RF module is designed and fabricated, whose correct operations are confirmed through both simulation and measurement. These results raise the availability of controlling large-scale quantum systems by low-power superconductor technology in the future.
Abstract The use of high-frequency input signals from room-temperature microwave sources makes it difficult to scale up the number of quantum bits in universal quantum computers. To address this issue, superconducting single flux quantum (SFQ) integrated circuits are being explored as suitable candidates for qubit manipulation in universal quantum computers. This paper deals with a scalable SFQ qubit control circuit (SQCC) structure that requires only low-frequency input. The circuit mainly consists of a pulse generator and a counter, that output the SFQ pulse train with adjustable frequency and a controllable number of pulses, which is applicable to control single-qubit Clifford operations. The design of low-voltage rapid single flux quantum (LV-RSFQ) and energy-efficient rapid single flux quantum (ERSFQ) for the SQCC achieves low power consumption and provides a basis for scaling up SQCC to control more qubits. The proposed circuits are fabricated under the SIMIT-Nb03 process and successfully pass test verification. The achieved test results reveal that the adjustable output frequency ranges of the SQCC based on the LV-RSFQ and ERSFQ designs in order are [2.40, 8.11] GHz and [4.81, 5.14] GHz. In the operating frequency range, the circuit is able to generate the correct number of SFQ pulses under control. The controllable number range is from 1 to 128. When the circuits operate at 5 GHz, the total power consumptions of the above circuits in order are 23.88 μW and 6.2 μW. All input signals are low-frequency signals, which frees the control of large-scale qubits from limitations caused by high-frequency inputs produced by room-temperature microwave sources.
Superconductive microwave rapid single-flux-quantum (RSFQ) digital circuits offer the possibility to digitally process signals in the frequency range of tens of GHz. An example of application to bring the advantages of this technology deals with digital SQUIDs, used for sensitive magnetometry with a broadband dynamics connected to a slew-rate in the GHz range. First recently obtained results of digital SQUID operation, based on Nb/Al-Al2O3/Nb shunted Josephson junctions, are presented in this article. In order to obtain the best performance of RSFQ circuits, and especially to push their speed at its limits, a precise diagnostic of such circuits is needed. We are developing a time-resolved diagnostic system based on sensitive photoconductive switches to sample the weak signals coming out of RSFQ circuits at cryogenic temperature. This system includes two different sorts of opto-RSFQ interfaces, based on superconducting and semiconducting materials, respectively. Some simulation results in the microwave range, along with measurements giving the potentialities of different photoswitches are presented.
We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.
Rapid-Single-Flux-Quantum (RSFQ) digital circuits based on shunted Josephson junctions have been shown to be able to digitally process signals up to several hundreds GHz. The principle of operation is based on the generation, transport and processing of picosecond voltage pulses of 2.07 mV.ps quantized area, which corresponds to one quantum flux h/2e. Operation of RSFQ circuits can be performed with clock frequencies of the order of 20 to 50 GHz with present technology. We will present current developments and experimental results obtained so far, based on circuits developed in the JeSEF RSFQ process of IPHT Jena, using a 1 kA/cm2 shunted Nb/Al-AlOx/Nb junctions. Some particular potential applications for space will be emphasized
Abstract To meet the specification of the qubits in our laboratory, a 0.4 kA·cm −2 superconducting rapid single flux quantum (RSFQ) circuit was designed and successfully fabricated with an improved Nb‐based self‐aligned lift‐off process. This circuit consists of a single‐flux‐quantum (SFQ) pulse generator, a Josephson transmission line (JTL) and a T‐flip flop (TFF), and it acts as a frequency divider. The values of the inductors in this circuit were extracted using InductEX and the basic function of this circuit was confirmed using the simulation software WRspice before fabrication. After fabrication, the basic parameters of this circuit were measured at ~ 2.5 K in a Janis He‐3 cryostat. This work laid the theoretical and experimental basis for the future research on the RSFQ‐qubit control circuits.