Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González, Shin’ichiro Asayama, M. Kroug, Keiko Kaneko, Hideo Ogawa, Yoshinori Uzawa

Published Nov 30, 2016• 13 citations
Publisher

Abstract

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

DOI
10.1088/0953-2048/30/2/024001

Related papers

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2014•2 citations

A 385-500 GHz Low Noise Superconductor-Insulator- Superconductor Mixer for ALMA Band 8

Wenlei Shan

We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.

IEICE Transactions on Electronics•Feb 1, 2006•11 citations

Design and Performance of a Sideband Separating SIS Mixer for 800–950 GHz

Andrey V. Khudchenko, M. Yu. Fominsky, Christopher Heiter +11 more

We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•21 citations

Balanced superconductor–insulator–superconductor mixer on a 9 µm silicon membrane

M. Westig, K Jacobs, J Stutzki +3 more

We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a $9 μ$m thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al$_{2}$O$_{3}$/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.

arXiv:1105.1956•Superconductor Science and Technology•Jul 1, 2011•32 citations

275–500-GHz Wideband Waveguide SIS Mixers

Takafumi Kojima, M. Kroug, Álvaro González +5 more

We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.

IEEE Transactions on Terahertz Science and Technology•Oct 1, 2018•22 citations

Design and Development of SIS Mixers for ALMA Band 10

Wenlei Shan, Sheng‐Cai Shi, T. Matsunaga +4 more

We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•40 citations
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.
We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.
We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a 9μ9 μ9μm thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al2_{2}2​O3_{3}3​/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.
We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.
We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.