We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.
We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.
We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.
In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).
We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.
We report on the continuing development of submillimeter quasi-optical slot antenna SIS mixers which use two-junction tuning circuits [1]. The mixers use 10 kA/cm2 Nb/Al-Oxide/Nb junctions and Nb wiring, and have generated DSB receiver noise temperatures around 5hv/kB to 700 GHz, and 16hv/kB (620 K) at 798 GHz. We present Fourier-transform spectrometer (FTS) measurements and heterodyne measurements on several such devices. In general, the measured response at frequencies below the gap of Nb is in good agreement with the predicted performance. Introduction SIS mixers with Nb-trilayer tunnel junctions offer excellent performance at frequencies below 800 GHz, and should perform competitively at frequencies as high as 1.4 THz [2-5]. Our goal is to develop a suite of ultra-low-noise SIS mixers which cover frequencies from = 400 GHz to more than I THz. At frequencies below the Nb gap (< 700 GHz), existing devices perform quite well [6], but further improvements in noise temperatures remain important. In addition, it is quite useful to be able to predict device performance given the design parameters. One can then optimize the device design for a particular frequency band, and confirm that we indeed understand the physics of the device. Progress in the design and operation of devices in this frequency range is presented below. At frequencies above the Nb gap, RF photons can break Cooper pairs, resulting in greater signal loss and higher receiver noise temperatures. The loss is particularly important in the slender microstrip lines used to resonate the junction capacitance and to transform the antenna impedance down to the RF junction impedance. However, the actual coupling of radiation into Nb junctions above the gap should still be reasonably efficient -more than 30% at 800 GHz [7]. In addition to RF loss, one is also affected by increased dispersion at frequencies near the gap. The Nb microstriplines have therefore been carefully designed to ensure the desired bandpass is achieved. We demonstrate for the first time that all-Nb SIS receivers can have substantially better performance than GaAs Schottky receivers for the astronomically important CI ( P2 — P 1 ) and CO (7-6) transitions near 810 GHz. Receiver Configuration Since waveguide mixers become difficult to construct at short submillimeter wavelengths, we have adopted a quasi-optical approach. Here, lenses take the place of waveguide horns, and the incoming radiation is collected by a planar antenna on the SIS mixer substrate [8]. This offers several other advantages, such as on-chip broad-band silt a SS 114 SSE WA Wa Sta MX Dewar 120 Mylar Window SIS Mixer 295 IQ 77 K Mylar Load Bearnsplitter ICI 1= NZ IC =1 HEN1T Amplifier Polyethylene Lens