Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

A 385 to 500-GHz SIS mixer the for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev, Alexey Pavolotsky, Igor Lapkin

Published Jun 14, 2006• 5 citations
Publisher

Abstract

The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.

DOI
10.1117/12.669797

Related papers

SIS Mixer for 385-500 GHz with On-Chip LO injection

Raquel Rodriguez Monje, Victor Y. Belitsky, Christophe Risacher +2 more

We present the design and first experimental results of a 385-500 GHz fixed-tuned double sideband (DSB) receiver based on a superconductor-insulator-superconductor (SIS) junction mixer with on-chip LO injection circuitry. At high frequency, branch waveguide couplers are difficult to manufacture with required accuracy as the branches (slots) become extremely narrow. In order to solve this problem, we propose a coupler integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO directional coupler is made of superconducting lines with slot lines in the ground plane. Thus, the coupler is integrated into conventional SIS junction fabrication steps, benefiting from the processing accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material. This termination gives very broadband performance using a compact area. Moreover, it is very tolerant to the sheet resistivity of the film, geometry and does not require any physical grounding [1]. The mixer is to be used at the Atacama Pathfinder EXperiment (APEX) telescope in Chile [2].

Softwaretechnik-Trends•Jan 1, 2007•6 citations

A 0.5 THz Sideband Separation SIS Mixer for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +6 more

Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.

•Apr 1, 2008•4 citations

A 275- to 370-GHz SIS mixer for the APEX telescope

Christophe Risacher, Victor Y. Belitsky, Vessen Vassilev +1 more

Atacama Pathfinder EXperiment (APEX) submillimeter telescope is currently under completion on Chajnator, at an altitude of 5050 m on the Atacama Desert, in the Northern Chile. The telescope facility heterodyne receivers should have 3 bands covering 211-500 GHz. We present design of a 275-370 GHz SIS mixer to be used as a first light APEX Band 2 receiver. A novel waveguide-to-microstrip transition with integrated bias-T is used in this mixer. This structure allows coupling of the RF signal from a full height waveguide to a thin-film superconducting line via E-probe. The wide side of the probe is connected to another port via a specially shaped high impedance line that provides RF/DC isolation. This port is used to extract the IF signal and to inject a DC current that creates a local magnetic field parallel to the plane of the SIS junction to suppress the Josephson effect. The main advantage of this type of Josephson suppression circuit is its compactness as it uses the existing superconducting lines from the SIS integrated tuning circuitry. The entire structure with the probe, SIS junction with its tuning circuitry is placed on a quartz substrate. For more advanced designs, as a sideband separating or balanced mixer that we intend to have for the final version of the APEX telescope heterodyne receiver, the SIS junctions of two balanced or quadrature mixers will be at a very close distance. The standard solution of using superconducting coils to suppress Josephson effect is very difficult to implement and, therefore, this new structure should be of a great advantage.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 8, 2004•0 citations

Design and Characterization of a 211–275 GHz Sideband Separating Mixer for the APEX Telescope

Vessen Vassilev, Doug W. Henke, Igor Lapkin +4 more

We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.

IEEE Microwave and Wireless Components Letters•Jan 1, 2008•22 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Design and Performance of a Sideband Separating SIS Mixer for 800–950 GHz

Andrey V. Khudchenko, M. Yu. Fominsky, Christopher Heiter +11 more

We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•21 citations
The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.
We present the design and first experimental results of a 385-500 GHz fixed-tuned double sideband (DSB) receiver based on a superconductor-insulator-superconductor (SIS) junction mixer with on-chip LO injection circuitry. At high frequency, branch waveguide couplers are difficult to manufacture with required accuracy as the branches (slots) become extremely narrow. In order to solve this problem, we propose a coupler integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO directional coupler is made of superconducting lines with slot lines in the ground plane. Thus, the coupler is integrated into conventional SIS junction fabrication steps, benefiting from the processing accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material. This termination gives very broadband performance using a compact area. Moreover, it is very tolerant to the sheet resistivity of the film, geometry and does not require any physical grounding [1]. The mixer is to be used at the Atacama Pathfinder EXperiment (APEX) telescope in Chile [2].
Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.
Atacama Pathfinder EXperiment (APEX) submillimeter telescope is currently under completion on Chajnator, at an altitude of 5050 m on the Atacama Desert, in the Northern Chile. The telescope facility heterodyne receivers should have 3 bands covering 211-500 GHz. We present design of a 275-370 GHz SIS mixer to be used as a first light APEX Band 2 receiver. A novel waveguide-to-microstrip transition with integrated bias-T is used in this mixer. This structure allows coupling of the RF signal from a full height waveguide to a thin-film superconducting line via E-probe. The wide side of the probe is connected to another port via a specially shaped high impedance line that provides RF/DC isolation. This port is used to extract the IF signal and to inject a DC current that creates a local magnetic field parallel to the plane of the SIS junction to suppress the Josephson effect. The main advantage of this type of Josephson suppression circuit is its compactness as it uses the existing superconducting lines from the SIS integrated tuning circuitry. The entire structure with the probe, SIS junction with its tuning circuitry is placed on a quartz substrate. For more advanced designs, as a sideband separating or balanced mixer that we intend to have for the final version of the APEX telescope heterodyne receiver, the SIS junctions of two balanced or quadrature mixers will be at a very close distance. The standard solution of using superconducting coils to suppress Josephson effect is very difficult to implement and, therefore, this new structure should be of a great advantage.
We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.