Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Softwaretechnik-Trends

SIS Mixer for 385-500 GHz with On-Chip LO injection

Raquel Rodriguez Monje, Victor Y. Belitsky, Christophe Risacher, Vessen Vassilev, Alexey Pavolotsky

Published Jan 1, 2007• 6 citations
OpenAlex

Abstract

We present the design and first experimental results of a 385-500 GHz fixed-tuned double sideband (DSB) receiver based on a superconductor-insulator-superconductor (SIS) junction mixer with on-chip LO injection circuitry. At high frequency, branch waveguide couplers are difficult to manufacture with required accuracy as the branches (slots) become extremely narrow. In order to solve this problem, we propose a coupler integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO directional coupler is made of superconducting lines with slot lines in the ground plane. Thus, the coupler is integrated into conventional SIS junction fabrication steps, benefiting from the processing accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material. This termination gives very broadband performance using a compact area. Moreover, it is very tolerant to the sheet resistivity of the film, geometry and does not require any physical grounding [1]. The mixer is to be used at the Atacama Pathfinder EXperiment (APEX) telescope in Chile [2].

Related papers

A 385 to 500-GHz SIS mixer the for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +2 more

The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•5 citations

A 0.5 THz Sideband Separation SIS Mixer for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +6 more

Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.

•Apr 1, 2008•4 citations

ALMA Band 5 (163-211 GHz) Sideband Separation Mixer Design

Bhushan Billade, Victor Y. Belitsky, Alexey Pavolotsky +4 more

We present the design of ALMA Band 5 sideband separation mixer based on Niobium superconducting SIS junctions and first experimental results for the double side band mixer. In this mixer the LO injection circuitry is integrated on the mixer substrate using a microstrip line directional coupler with slot-line branches in the ground plane. The isolated port of the LO coupler is terminated by a wideband floating elliptical termination. The mixer employs two SIS junctions with junction area of 3 ?m2 each, in twin junction configuration, followed by a quarter wave transformer to couple it to the RF probe. First measurements of the DSB mixer show promising results with noise temperature around 35K over the entire band.

Softwaretechnik-Trends•Apr 1, 2008•4 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Development of an SIS(Superconductor-Insulator-Superconductor) Junction Mixer over 120∼180 GHz Band

Moon‐Hee Chung, Changhoon Lee, Kwang-Dong Kim +1 more

A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.

The Journal of Korean Institute of Electromagnetic Engineering and Science•Jan 1, 2004•0 citations

Design and Performance of a Sideband Separating SIS Mixer for 800–950 GHz

Andrey V. Khudchenko, M. Yu. Fominsky, Christopher Heiter +11 more

We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•21 citations
We present the design and first experimental results of a 385-500 GHz fixed-tuned double sideband (DSB) receiver based on a superconductor-insulator-superconductor (SIS) junction mixer with on-chip LO injection circuitry. At high frequency, branch waveguide couplers are difficult to manufacture with required accuracy as the branches (slots) become extremely narrow. In order to solve this problem, we propose a coupler integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO directional coupler is made of superconducting lines with slot lines in the ground plane. Thus, the coupler is integrated into conventional SIS junction fabrication steps, benefiting from the processing accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material. This termination gives very broadband performance using a compact area. Moreover, it is very tolerant to the sheet resistivity of the film, geometry and does not require any physical grounding [1]. The mixer is to be used at the Atacama Pathfinder EXperiment (APEX) telescope in Chile [2].
The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.
Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.
We present the design of ALMA Band 5 sideband separation mixer based on Niobium superconducting SIS junctions and first experimental results for the double side band mixer. In this mixer the LO injection circuitry is integrated on the mixer substrate using a microstrip line directional coupler with slot-line branches in the ground plane. The isolated port of the LO coupler is terminated by a wideband floating elliptical termination. The mixer employs two SIS junctions with junction area of 3 ?m2 each, in twin junction configuration, followed by a quarter wave transformer to couple it to the RF probe. First measurements of the DSB mixer show promising results with noise temperature around 35K over the entire band.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.
We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.