Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Electronics

A 385-500 GHz Low Noise Superconductor-Insulator- Superconductor Mixer for ALMA Band 8

Wenlei Shan

Published Feb 1, 2006• 11 citations
Publisher

Abstract

We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.

DOI
10.1093/ietele/e89-c.2.170

Related papers

Design and Development of SIS Mixers for ALMA Band 8

Wenlei Shan, Takashi Noguchi, S. C. Shi +1 more

In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•27 citations

Design and Development of SIS Mixers for ALMA Band 10

Wenlei Shan, Sheng‐Cai Shi, T. Matsunaga +4 more

We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•40 citations

275–500-GHz Wideband Waveguide SIS Mixers

Takafumi Kojima, M. Kroug, Álvaro González +5 more

We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.

IEEE Transactions on Terahertz Science and Technology•Oct 1, 2018•22 citations

SIS Mixer Fabrication for ALMA Band10

M. Kroug, Akira Endo, T. Tamura +6 more

Band10 of the Atacama Large Millimeter Array (ALMA) is a planned heterodyne receiver covering the frequency range 790 GHz-950 GHz. The waveguide mixers are superconductor insulator superconductor (SIS) Nb/Al-AlOx/Nb junctions integrated with NbTiN/SiO2/Al tuning circuits. Our junction definition process has been greatly simplified by introducing an inductively-coupled-plasma (ICP) etcher to the fabrication. The etching process, which employs a low-pressure CF4/O2plasma, allows to remove the entire Nb/Al-AlOx/Nb tri-layer in asinglestep. SIS mixers with current densities up to 10 kA/cm2and quality factor above 15 have been fabricated with good reproducibility. Minimum receiver noise temperature, corrected for optical losses, is 210 K at 860 GHz. With the goal to further improve the performance, optimization of circuit design and fabrication technology are discussed.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•24 citations

Design Of Dual Polarisation Sideband Separation Mixer For ALMA Band 5

Bhushan Billade

This licentiate is focused on the design and development of Superconductor-Insulator-Superconductor (SIS) junction mixer for ALMA Band 5, one of the ten frequency bands of the Atacama Large Millimeter Array (ALMA) project. ALMA Band 5 is a dual polarisation sideband separation heterodyne receiver covering radio frequencies (RF) from 163 GHz to 211 GHz, with 4-8 GHz intermediate frequency (IF). Amongst the other ALMA bands, Band 5 is the lowest frequency band, which uses all-cold optics. That puts strong constrains on the dimensions of all the receiver components. For the SIS mixer, we employ a MMIC-like approach where most of the DSB mixer components, including LO injection circuitry with novel directional coupler, are integrated on the same crystal quartz substrate. The mixer uses a lumped filter technique to extract the IF frequencies, which is non-traditional for SIS mixers. A custom made superconducting Lange coupler with suspended air bridges to connect the fingers of Lange coupler is used. Experimental measurements of the double sideband mixer show state of the art performance with the receiver noise temperature below 30 Kelvin across the entire band. The noise temperature for sideband separation mixer is below 60 Kelvin with sideband rejection better than 12 dB over most of the band.

•Sep 1, 2009•1 citation

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations
We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.
In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).
We present the design and preliminary experimental results of superconductor-insulator-superconductor (SIS) mixers for Atacama large millimeter array (ALMA) band 10 (780-950GHz) receivers. To achieve wide frequency coverage as well as low noise temperature, we integrated high current density (10 kA/cm2) and small-sized (one micrometer in diameter) Nb/AlOx/Nb SIS junctions with a tuning microstrip line using NbTiN ground plane and Al wiring layers. High quality NbTiN films with Tc reaching 14.5 K and Al films with residual resistivity ratio as large as 15 have been achieved. To minimize the waveguide transmission loss and facilitate the fabrication of mixer block, a full height waveguide was adopted. The waveguide probe was optimized to achieve low input impedance in the frequency range of 780-950 GHz while adopting a backshort cavity of zero depth. Preliminary RF testing with a Nb/Al microstrip tuning circuit demonstrated a DSB receiver noise temperature about 400 K at 832.5 GHz, which promises the accommodation of receiver performance in ALMA specification with low loss NbTiN/Al microstrip lines.
We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.
Band10 of the Atacama Large Millimeter Array (ALMA) is a planned heterodyne receiver covering the frequency range 790 GHz-950 GHz. The waveguide mixers are superconductor insulator superconductor (SIS) Nb/Al-AlOx/Nb junctions integrated with NbTiN/SiO2/Al tuning circuits. Our junction definition process has been greatly simplified by introducing an inductively-coupled-plasma (ICP) etcher to the fabrication. The etching process, which employs a low-pressure CF4/O2plasma, allows to remove the entire Nb/Al-AlOx/Nb tri-layer in asinglestep. SIS mixers with current densities up to 10 kA/cm2and quality factor above 15 have been fabricated with good reproducibility. Minimum receiver noise temperature, corrected for optical losses, is 210 K at 860 GHz. With the goal to further improve the performance, optimization of circuit design and fabrication technology are discussed.
This licentiate is focused on the design and development of Superconductor-Insulator-Superconductor (SIS) junction mixer for ALMA Band 5, one of the ten frequency bands of the Atacama Large Millimeter Array (ALMA) project. ALMA Band 5 is a dual polarisation sideband separation heterodyne receiver covering radio frequencies (RF) from 163 GHz to 211 GHz, with 4-8 GHz intermediate frequency (IF). Amongst the other ALMA bands, Band 5 is the lowest frequency band, which uses all-cold optics. That puts strong constrains on the dimensions of all the receiver components. For the SIS mixer, we employ a MMIC-like approach where most of the DSB mixer components, including LO injection circuitry with novel directional coupler, are integrated on the same crystal quartz substrate. The mixer uses a lumped filter technique to extract the IF frequencies, which is non-traditional for SIS mixers. A custom made superconducting Lange coupler with suspended air bridges to connect the fingers of Lange coupler is used. Experimental measurements of the double sideband mixer show state of the art performance with the receiver noise temperature below 30 Kelvin across the entire band. The noise temperature for sideband separation mixer is below 60 Kelvin with sideband rejection better than 12 dB over most of the band.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.