Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

Published Jan 1, 2014• 2 citations
Publisher

Abstract

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

DOI
10.2221/jcsj.49.359

Related papers

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Balanced superconductor–insulator–superconductor mixer on a 9 µm silicon membrane

M. Westig, K Jacobs, J Stutzki +3 more

We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a $9 μ$m thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al$_{2}$O$_{3}$/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.

arXiv:1105.1956•Superconductor Science and Technology•Jul 1, 2011•32 citations

Design and Performance of a Sideband Separating SIS Mixer for 800–950 GHz

Andrey V. Khudchenko, M. Yu. Fominsky, Christopher Heiter +11 more

We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•21 citations

An SIS Mixer With 2hf/k DSB Noise Temperature at 163 - 211 GHz Band

Bhushan Billade, Alexey Pavolotsky, Victor Y. Belitsky

We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.

IEEE Transactions on Terahertz Science and Technology•May 2, 2013•20 citations

Sideband Separating Mixer for atmospheric window 790-950 GHz

Andrey V. Khudchenko

We have developed a Sideband Separating (2SB) Mixer based on superconductor-insulator-superconductor (SIS) junctions for frequency range 790-950 GHz. In the first test this mixer demonstrated the noise temperature from 450 to 900 K and the image rejection ratio above 15dB in 95% of the band. The SIS mixers used here have DSB noise temperature form 220 to 400 K. These results show that RF waveguide hybrid structure for such a high frequencies can be manufactured with losses level below 0.8 dB. It makes attractive possible ALMA upgrade of Band 10 receivers to 2SB option, because the sensitivity for spectral lines observations can be improved by about 30% by using 2SB mixers instead of DSB ones.

•Jun 6, 2019•0 citations

Development of an SIS(Superconductor-Insulator-Superconductor) Junction Mixer over 120∼180 GHz Band

Moon‐Hee Chung, Changhoon Lee, Kwang-Dong Kim +1 more

A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.

The Journal of Korean Institute of Electromagnetic Engineering and Science•Jan 1, 2004•0 citations
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a 9μ9 μ9μm thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al2_{2}2​O3_{3}3​/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.
We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.
We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.
We have developed a Sideband Separating (2SB) Mixer based on superconductor-insulator-superconductor (SIS) junctions for frequency range 790-950 GHz. In the first test this mixer demonstrated the noise temperature from 450 to 900 K and the image rejection ratio above 15dB in 95% of the band. The SIS mixers used here have DSB noise temperature form 220 to 400 K. These results show that RF waveguide hybrid structure for such a high frequencies can be manufactured with losses level below 0.8 dB. It makes attractive possible ALMA upgrade of Band 10 receivers to 2SB option, because the sensitivity for spectral lines observations can be improved by about 30% by using 2SB mixers instead of DSB ones.
A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.