Digital circuits have been developed to interface superconductive electronic chips with high speed 50-/spl Omega/ transmission lines. Digital data at 1 Gigabit per second was transferred through a Josephson chip in a first cryostat to another Josephson chip in a second cryostat. The chips were connected by more than 3 meters of 50-/spl Omega/ transmission line. No semiconductor amplifiers were used in this data path. A Hewlett Packard data source provided the original data to the first chip, which converted it to SFQ data. Output interface circuits were driven by a 2-GHz external clock to latch series strings of 10 junctions and drive 2-Gbps data into a 50-/spl Omega/ cable. In the second cryostat, a latching three-junction interferometer with a two-turn control line converted the input signal to latched data and switched an MVTL OR-gate output. This demonstration showed that low-power Josephson digital circuits can be integrated into multichip digital subsystems that can pass data at high rates without the use of power-hungry semiconductor amplifiers.
Digital circuits have been developed to interface superconductive electronic chips with high speed 50-/spl Omega/ transmission lines. Digital data at 1 Gigabit per second was transferred through a Josephson chip in a first cryostat to another Josephson chip in a second cryostat. The chips were connected by more than 3 meters of 50-/spl Omega/ transmission line. No semiconductor amplifiers were used in this data path. A Hewlett Packard data source provided the original data to the first chip, which converted it to SFQ data. Output interface circuits were driven by a 2-GHz external clock to latch series strings of 10 junctions and drive 2-Gbps data into a 50-/spl Omega/ cable. In the second cryostat, a latching three-junction interferometer with a two-turn control line converted the input signal to latched data and switched an MVTL OR-gate output. This demonstration showed that low-power Josephson digital circuits can be integrated into multichip digital subsystems that can pass data at high rates without the use of power-hungry semiconductor amplifiers.
Interface circuits for the transfer of data between Single Flux Quantum (SPQ) circuits have been designed, fabricated, and operated at speeds up to 3 Gigabits per second. The circuit employed an improved version of the SFQ/Latch converter, a Modified Variable Threshold Logic (MVTL) OR/AND gate, a 3/spl times/ latching amplifier, and a 3/spl times/-to-10/spl times/ latching amplifier. The amplifier circuits employed stacks of latching junctions. Resistors between the parallel stacks of junctions damped residual currents to prevent flux trapping during reset. Tolerance to critical current variations in the series stacks of junctions was provided by inductive chokes on the input junction shunting resistors. Microwave modeling programs were used to ensure proper distribution of the applied current to all of the latching elements. The circuit transferred data at 3 Gigabits per second from one SFQ circuit up to room temperature and back to another SFQ circuit through 3.4 meters of 50-ohm cable.
Spread spectrum data modulation, transmission, and demodulation has been demonstrated between SFQ chips in separate dewars. The baseband demonstration consisted of modulating (encoding) data with a spreading code, transmitting the coded data to a Receiver and demodulating (decoding) the data using an identical spreading code. The Transmitter code was produced by a 2 GHz, 4-bit SFQ pseudorandom sequence generator creating a 15-chip spreading code, which modulated a /spl sim/133 MHz data source. This data was output by a 10/spl times/ superconducting latch providing /spl sim/8 mV of AC drive. This signal was fed through 50-/spl Omega/ coaxial cable to a SFQ Receiver chip in a separate dewar. No amplification of the AC signal between the dewars was needed, however, a slight DC bias was added to the signal as a flux bias for the input SQUID on the Receiver. The Receiver chip consisted of an identical SFQ pseudorandom sequence generator and a data demodulation gate. Demodulating the received data with the code generator produced a replica of the data signal in RZ form. Both time forward and time reversed codes for the spreading/despreading sequence were created.
A critical component for high bandwidth communications links is a digital switch. Desirable features of a digital switch include: high input/output bandwidth, high channel count, scalability, low latency and interchannel skew. Superconductive circuits, with simultaneous high speed and low power advantages (even including the requisite cryocooler) have been applied to a highly scaleable crossbar switch, useful in supercomputer networks, massively parallel processing (MPP), and high data rate telecommunications. We report here on the testing of a 16/spl times/16 switch chip based on the switch chip component of the highly scaleable crossbar system. We have successfully transmitted multi-Gb/s data through this superconducting switch, with packet destination addressing decoded from the header of the data packet. The data are transmitted to a separate superconducting amplifier chip, mounted on a superconducting multi-chip module with the switch. The switch is a crossbar architecture, voltage state design, and operated to beyond 3 Gb/s. The amplifier is a clocked latching stack of Josephson junctions. Output of the amplifier at 6.2 Gb/s is 7.0 mV, which facilitates the interface of the module to its users. BER of the two-chip assembly is 10/sup -9/ or less above 2 Gb/s.
Superconductive electronics offers a unique combination of high bandwidth and low power for mission critical hardware such as digital processors at 20 to 100 GHz, microwatt per bit analog to digital converters, large digital switches at multi-Gb/s data rates, and low noise parametric amplifiers. This cryogenic technology, typically operating at a few degrees or a few tens of degrees Kelvin, depends upon the unique physics of superconducting materials such as Nb, NbN, and YBaCuO, and the fundamental circuit element, the Josephson junction (JJ) to create unique architectures of unprecedented design efficiency and performance. These circuits are based on the single flux quantum (SFQ) logic family, a technology that has no parallel in semiconductor electronics. Digital data is transmitted by voltage pulses with amplitude less than 1 mV, but at extremely high speeds. Individual gates have been operated as high as 370 GHz. In this paper, we present a brief overview of superconductive digital technology, describe some recent circuits, and discuss how the challenges to superconductive technology are being met, including the use of multi-chip module (MCM) technology, and the potential use of III-V HBT and HEMT circuits to provide interface drivers and amplifiers, possibly operated cryogenically.
Superconductor electronics for high-performance computing and high-speed analog-to-digital converters requires multi-channel digital data links. Most difficult is the amplification of the weak signals from the superconductor circuit to the volt level of semiconductor electronics. We developed a hybrid digital interface based on a Josephson latching driver, the so-called Suzuki stack, and a clocked CMOS comparator. The input can be directly triggered by a single flux quantum pulse and the output provides a 1 V CMOS-level signal. In contrast to existing systems, our interface is optimized for ultra-low-power consumption to enable its application for parallel multi-bit data interfaces. We provide evaluation of various types of Suzuki stacks and various CMOS comparators. We present experimental data on the delay of the overall hybrid interface and the total power consumption. The bit-error rate has been measured to be below 10-12. We will discuss the trade-off among circuit robustness, speed, and power consumption.
We have developed and tested simple and inexpensive electronics for interfacing Rapid Single-Flux-Quantum (RSFQ) Josephson-junction circuits to room temperature digital systems. Voltage-level (Non-Return-to-Zero) bit signals with a swing of /spl sim/150 uV, developed on-chip by standard SFQ/DC converters, and in some cases amplified to 1.5 mV swing by HUFFLE-type circuits, are passed to the 300 K environment using a high density (40 channel) flexible coplanar waveguide assembly. AC-coupled, 2-3 stage microwave Si-bipolar amps, and Emitter-Coupled-Logic (ECL) buffers accomplish voltage level translation to the standard ECL levels, Using this technique, data rates in excess of 1 Gb/s per channel can be achieved at low cost per channel,.>