Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Noise and Bandwidth of 0.5-THz Twin Vertically Stacked SIS Junctions

Jing Li, Sheng‐Cai Shi, Dong Liu, Kangmin Zhou, Ming-Jye Wang, Tse-Jun Chen, Chong‐Wen Chen, Wei-Chun Lu, Chuang-Ping Chiu, Hsian-Hong Chang

Published Jan 7, 2011• 1 citation
Publisher

Abstract

Twin SIS (superconductor-insulator-superconductor) junctions, with a simple structure, yet large bandwidth and low noise temperature, have been widely used in millimeter- and submillimeter-wave heterodyne mixers. With increasing frequency, however, the length of the tuning inductance connecting the two individual SIS junctions becomes short while the junction area remains fixed. With a relatively short tuning inductance, the effect of the junction's spreading inductance becomes non-negligible, and device fabrication becomes more difficult. By adopting vertically stacked SIS junctions (VSJs), which have an equivalent geometric capacitance inversely proportional to the junction number, it becomes feasible to increase the junction tuning inductance. In this paper, we report on the design, fabrication, and characterization of twin Nb/Al-AlOx/Nb/Al-AlOx/Nb VSJs for the 500-GHz frequency band.

DOI
10.1109/tasc.2010.2096493

Related papers

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

Low-noise THz Niobium SIS Mixers

Mei Bin

This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.

•Sep 1, 1997•8 citations

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

Characterization of the Mixing Performance of All-NbN Superconducting Tunnel Junctions at 0.5 THz

Jing Li, Mahoto Takeda, Zhen Wang +1 more

With a gap frequency of 1.4 THz, all-NbN Superconductor-Insulator-Superconductor (SIS) junctions are potentially applicable to sensitive heterodyne mixers for THz astronomy and atmospheric research. In this paper, we report the design, fabrication, and performance characterization of a 0.5-THz waveguide SIS mixer incorporating twin NbN/AlN/NbN junctions and an NbN/MgO/NbN tuning circuit with no impedance transformers. The noise performance of two NbN SIS junctions with different tuning inductances is measured, compared with the simulated results without and with the multiple Andreev reflection (MAR) effect taken into account, and also compared with the video detection response. In addition, the IF-output-power stability and aging effect of fabricated NbN SIS junctions are investigated.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•13 citations

Submillimeter mixers based on superconductive parallel junction arrays

Faouzi M. Boussaha, Morvan C. Salez, Y. Delorme +4 more

Observation and analysis of submillimeter-wave radiation (300GHz-3THz) in astronomy and atmospheric sciences requires increasingly performant receivers. The most sensitive receivers working in this range of electromagnetic spectrum use superconductor-insolator-superconductor (SIS) junctions. In order to increase the bandwidth and the sensitivity, we are developing a quantum-noise limited heterodyne receiver based on several parallel SIS junctions with broad (larger than 30%) fixed tuned bandwidth. These circuits can be viewed as passband filters which have been optimized by varying the spacings between junctions. We have designed such 5-junction arrays for operation in the range 480-640 GHz. Fabrication and heterodyne characterization of these devices has been done. The 1 μm2 junctions current density ranges from 4 to 13 kA/cm2, using optical lithography and Nb/Al2Nb5/Nb trilayer sputtering technology. The fabrication process and yield are presented in this paper, along with measured performances

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 2003•1 citation

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology - art. no. 684013

Jing Li, Takeda Masanon, Zhen Wang

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.

•Jan 1, 2008•0 citations
Twin SIS (superconductor-insulator-superconductor) junctions, with a simple structure, yet large bandwidth and low noise temperature, have been widely used in millimeter- and submillimeter-wave heterodyne mixers. With increasing frequency, however, the length of the tuning inductance connecting the two individual SIS junctions becomes short while the junction area remains fixed. With a relatively short tuning inductance, the effect of the junction's spreading inductance becomes non-negligible, and device fabrication becomes more difficult. By adopting vertically stacked SIS junctions (VSJs), which have an equivalent geometric capacitance inversely proportional to the junction number, it becomes feasible to increase the junction tuning inductance. In this paper, we report on the design, fabrication, and characterization of twin Nb/Al-AlOx/Nb/Al-AlOx/Nb VSJs for the 500-GHz frequency band.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
With a gap frequency of 1.4 THz, all-NbN Superconductor-Insulator-Superconductor (SIS) junctions are potentially applicable to sensitive heterodyne mixers for THz astronomy and atmospheric research. In this paper, we report the design, fabrication, and performance characterization of a 0.5-THz waveguide SIS mixer incorporating twin NbN/AlN/NbN junctions and an NbN/MgO/NbN tuning circuit with no impedance transformers. The noise performance of two NbN SIS junctions with different tuning inductances is measured, compared with the simulated results without and with the multiple Andreev reflection (MAR) effect taken into account, and also compared with the video detection response. In addition, the IF-output-power stability and aging effect of fabricated NbN SIS junctions are investigated.
Observation and analysis of submillimeter-wave radiation (300GHz-3THz) in astronomy and atmospheric sciences requires increasingly performant receivers. The most sensitive receivers working in this range of electromagnetic spectrum use superconductor-insolator-superconductor (SIS) junctions. In order to increase the bandwidth and the sensitivity, we are developing a quantum-noise limited heterodyne receiver based on several parallel SIS junctions with broad (larger than 30%) fixed tuned bandwidth. These circuits can be viewed as passband filters which have been optimized by varying the spacings between junctions. We have designed such 5-junction arrays for operation in the range 480-640 GHz. Fabrication and heterodyne characterization of these devices has been done. The 1 μm2 junctions current density ranges from 4 to 13 kA/cm2, using optical lithography and Nb/Al2Nb5/Nb trilayer sputtering technology. The fabrication process and yield are presented in this paper, along with measured performances
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.