Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics Conference Series

Atomic nanofabrication: perspectives for serial and parallel deposition

Dieter Meschede

Published Jan 1, 2005• 13 citations
Publisher

Abstract

Recent advances in atomic nanofabrication with laser manipulated atomic beams are discussed with regard to the creation of arbitrary structures.
DOI
10.1088/1742-6596/19/1/020

Related papers

Laser-focused atomic deposition – nanofabrication via atom optics

Jabez J. McClelland, R. J. Celotta

Thin Solid Films•May 1, 2000•22 citations

Laser manipulation of an atomic Cr beam for controlled deposition studies

Jabez J. McClelland, Robert E Scholten, Robert Celotta

Quantum Electronics and Laser Science Conference•May 2, 1993•0 citations

Atomic nanofabrication using an ytterbium atomic beam

R. Ohmukai, Shinji Urabe, Masayoshi Watanabe

Highly parallel and periodically narrow lines of ytterbium (Yb) atoms were successfully produced on a substrate using a near resonant laser light and direct-write atomic nanofabrication. Yb atoms are a promising material for nanofabrication using atom optics particularly due to their electric conductivity, the laser wavelength required for their manipulation, and the vapor pressure required for their fabrication. Collimated 174Yb atoms were channeled into the nodes of an optical standing wave with dipole force and then deposited onto a substrate. We clearly observed a grating pattern of Yb atoms fabricated on a substrate with a line separation of approximately 200 nm after examining the surface of the substrate with an atomic force microscope. This is the first demonstration of nanofabrication using the atom-optical approach with Yb atoms.

Science and Technology of Advanced Materials•Jan 1, 2004•5 citations

Laser manipulation of atoms and nanofabrication

Erich Jurdik

Fundamental interaction processes between atoms and photons are exploited to control external degrees of freedom of the atoms. Laser light, when properly tuned near an atomic resonance, exerts such forces that the atoms are repelled from or attracted to the regions with low light intensities. We use these forces to manipulate atom beams on nanometer-scale. In the simplest approach to nanofabrication via atom optics, a laser standing wave serves as a 'mask' through which the atoms are deposited onto a substrate. In this thesis we first present the modeling results on the focusing properties of a standing wave laser field and on the surface diffusion and growth phenomena in laser-focused atomic deposition. The development of our experimental facility for laser-manipulated deposition with chromium atoms (based on the obtained modeling results) is reported on. Thereafter, we demonstrate laser manipulation of chromium atoms and fabrication of nanostructures with these atoms. The results obtained in Nijmegen and also those obtained in collaboration with J.J. McClelland's group from the National Institute of Standards and Technology (Gaithersburg, Maryland, USA) are analyzed with the aim of understanding the role of atom-optical and surface growth phenomena in the fabrication process of laser-focused nanostructures

•Jan 1, 2001•5 citations

Simulation of laser-focused atomic deposition for nanostructure fabrication

Xianzhong Chen, Hanmin Yao, Xunan Chen

Optik•Jan 1, 2004•0 citations

Laser-Diode-Tuned Sequential Laser Atom Cooling and Trapping for Nanofabrications

Hong‐Bo Sun, Hironobu Inouye, Yasushi Inouye +2 more

We developed an atom-optical system that utilized a laser diode (LD) for both laser atom cooling and trapping. The LD is easy to maintain and operate, and is therefore suitable for engineering applications. The neutral atom beam of chromium was collimated by Doppler cooling and focused by a standing wave lens, and then directly deposited onto a silicon substrate. A nanograting structure with periodicity identical to the wavelength of the standing wave, 212.78 nm, was successfully achieved. The atom beam generation, collimating, focusing and deposition processes were experimentally and theoretically investigated.

Japanese Journal of Applied Physics•Jul 1, 2001•8 citations
Highly parallel and periodically narrow lines of ytterbium (Yb) atoms were successfully produced on a substrate using a near resonant laser light and direct-write atomic nanofabrication. Yb atoms are a promising material for nanofabrication using atom optics particularly due to their electric conductivity, the laser wavelength required for their manipulation, and the vapor pressure required for their fabrication. Collimated 174Yb atoms were channeled into the nodes of an optical standing wave with dipole force and then deposited onto a substrate. We clearly observed a grating pattern of Yb atoms fabricated on a substrate with a line separation of approximately 200 nm after examining the surface of the substrate with an atomic force microscope. This is the first demonstration of nanofabrication using the atom-optical approach with Yb atoms.
Fundamental interaction processes between atoms and photons are exploited to control external degrees of freedom of the atoms. Laser light, when properly tuned near an atomic resonance, exerts such forces that the atoms are repelled from or attracted to the regions with low light intensities. We use these forces to manipulate atom beams on nanometer-scale. In the simplest approach to nanofabrication via atom optics, a laser standing wave serves as a 'mask' through which the atoms are deposited onto a substrate. In this thesis we first present the modeling results on the focusing properties of a standing wave laser field and on the surface diffusion and growth phenomena in laser-focused atomic deposition. The development of our experimental facility for laser-manipulated deposition with chromium atoms (based on the obtained modeling results) is reported on. Thereafter, we demonstrate laser manipulation of chromium atoms and fabrication of nanostructures with these atoms. The results obtained in Nijmegen and also those obtained in collaboration with J.J. McClelland's group from the National Institute of Standards and Technology (Gaithersburg, Maryland, USA) are analyzed with the aim of understanding the role of atom-optical and surface growth phenomena in the fabrication process of laser-focused nanostructures
We developed an atom-optical system that utilized a laser diode (LD) for both laser atom cooling and trapping. The LD is easy to maintain and operate, and is therefore suitable for engineering applications. The neutral atom beam of chromium was collimated by Doppler cooling and focused by a standing wave lens, and then directly deposited onto a silicon substrate. A nanograting structure with periodicity identical to the wavelength of the standing wave, 212.78 nm, was successfully achieved. The atom beam generation, collimating, focusing and deposition processes were experimentally and theoretically investigated.