Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

SIS and bolometer mixers for terahertz frequencies

K. H. Gundlach, Matthias Schicke

Published Nov 23, 2000• 20 citations
Publisher

Abstract

The need for extremely sensitive heterodyne receivers in the astronomical community has created strong efforts to develop appropriate frequency mixers. Nb/Al-Al x O y -Nb tunnel junctions with Nb matching circuits lead to best results up to approximately 700 GHz, the energy-gap frequency of Nb. For higher frequencies the Nb in the matching circuit becomes lossy and is replaced beyond 800 GHz by Al (which operates in the normal conducting state). The gap frequency of NbN is as high as 1.2 THz, but NbN technology is not yet mature. Practical films still have substantial radio frequency losses and the barrier of NbN tunnel junctions is too leaky. More recently, NbTiN, for which the gap frequency is also about 1.2 THz, was found to have very low losses, and is therefore a good choice for tuning circuits. New interesting tunnel junctions for mixers around 1 THz are NbTiN-MgO-NbTiN and Nb/Al-AlN x -NbTiN. Excellent performance from about 1 THz up to several terahertz can be expected from hot-electron transition-edge bolometer mixers. They consist of NbN or Nb microbridges, they do not need matching circuits and their frequency limit is not determined by the gap frequency.

DOI
10.1088/0953-2048/13/12/202

Related papers

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology - art. no. 684013

Jing Li, Takeda Masanon, Zhen Wang

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.

•Jan 1, 2008•0 citations

Development of SIS mixers for 1 THz

Jonas Stasys Zmuidzinas, J. Kooi, Jonathan H. Kawamura +4 more

SIS heterodyne mixer technology based on niobium tunnel junctions has now been pushed to frequencies over 1 THz, clearly demonstrating that the SIS junctions are capable of mixing at frequencies up to twice the energy gap frequency (4(Delta) /h). However, the performance degrades rapidly above the gap frequency of niobium (2(Delta) /h approximately equals 700 GHz) due to substantial ohmic losses in the on-chip tuning circuit. To solve this problem, the tuning circuit should be fabricated using a superconducting film with a larger energy gap, such as NbN; unfortunately, NbN films often have a substantial excess surface resistance in the submillimeter band. In contrast, the SIS mixer measurements we present in this paper indicate that the losses for NbTiN thin films can be quite low.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 31, 1998•27 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

Low-noise submillimeter-wave NbTiN superconducting tunnel junction mixers

Jonathan H. Kawamura, Jian Chen, David Miller +5 more

We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.

Applied Physics Letters•Dec 20, 1999•81 citations

Low-noise waveguide SIS mixer with NbN/AlN/NbN tunnel junctions tuned by an NbN/MgO/NbTiN microstrip circuit

Masanori Takeda, Wenlei Shan, Takafumi Kojima +4 more

The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.

Superconductor Science and Technology•Jun 10, 2009•10 citations

Design of Terahertz SIS Mixers Using Nb/AlN/Nb Junctions Integrated With All-NbTiN Tuning Circuits

Yoshinori Uzawa, M. Kroug, Takafumi Kojima +7 more

We have designed superconductor-insulator-superconductor (SIS) mixers using Nb/AlN/Nb tunnel junctions integrated with NbTiN/SiO2/NbTiN microstrip tuning circuits for the Atacama Large Millimeter/submillimeter Array (ALMA) Band 10 (0.78-0.95 THz). In order to design the tuning circuits, we used terahertz time domain spectroscopy to experimentally derive the complex conductivity of relatively thick NbTiN films deposited on quartz substrate directly as a ground plane and on RF-sputtered SiO2as a microstrip. Results showed that the conductivities of both films can be described by a modified Mattis-Bardeen theory. We also investigated the junction heating effects originating from quasi-particle trapping in the Nb electrodes embedded in NbTiN circuits by varying the volume of the electrodes. It was confirmed that current-voltage curves of Nb/AlN/Nb tunnel junctions with thick (~200 nm) counter electrodes contacting NbTiN wirings showed higher gap voltages as well as reduced back-bending than those with thin (~50 nm) electrodes. Making use of these findings, our designed SIS mixers employing Nb/AlN/Nb junctions with a current density of 15 kA/cm2and all-NbTiN tuning circuits may cover the Band 10 with good sensitivity.

IEEE Transactions on Applied Superconductivity•Nov 28, 2016•12 citations
The need for extremely sensitive heterodyne receivers in the astronomical community has created strong efforts to develop appropriate frequency mixers. Nb/Al-Al x O y -Nb tunnel junctions with Nb matching circuits lead to best results up to approximately 700 GHz, the energy-gap frequency of Nb. For higher frequencies the Nb in the matching circuit becomes lossy and is replaced beyond 800 GHz by Al (which operates in the normal conducting state). The gap frequency of NbN is as high as 1.2 THz, but NbN technology is not yet mature. Practical films still have substantial radio frequency losses and the barrier of NbN tunnel junctions is too leaky. More recently, NbTiN, for which the gap frequency is also about 1.2 THz, was found to have very low losses, and is therefore a good choice for tuning circuits. New interesting tunnel junctions for mixers around 1 THz are NbTiN-MgO-NbTiN and Nb/Al-AlN x -NbTiN. Excellent performance from about 1 THz up to several terahertz can be expected from hot-electron transition-edge bolometer mixers. They consist of NbN or Nb microbridges, they do not need matching circuits and their frequency limit is not determined by the gap frequency.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.
SIS heterodyne mixer technology based on niobium tunnel junctions has now been pushed to frequencies over 1 THz, clearly demonstrating that the SIS junctions are capable of mixing at frequencies up to twice the energy gap frequency (4(Delta) /h). However, the performance degrades rapidly above the gap frequency of niobium (2(Delta) /h approximately equals 700 GHz) due to substantial ohmic losses in the on-chip tuning circuit. To solve this problem, the tuning circuit should be fabricated using a superconducting film with a larger energy gap, such as NbN; unfortunately, NbN films often have a substantial excess surface resistance in the submillimeter band. In contrast, the SIS mixer measurements we present in this paper indicate that the losses for NbTiN thin films can be quite low.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.
The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.
We have designed superconductor-insulator-superconductor (SIS) mixers using Nb/AlN/Nb tunnel junctions integrated with NbTiN/SiO2/NbTiN microstrip tuning circuits for the Atacama Large Millimeter/submillimeter Array (ALMA) Band 10 (0.78-0.95 THz). In order to design the tuning circuits, we used terahertz time domain spectroscopy to experimentally derive the complex conductivity of relatively thick NbTiN films deposited on quartz substrate directly as a ground plane and on RF-sputtered SiO2as a microstrip. Results showed that the conductivities of both films can be described by a modified Mattis-Bardeen theory. We also investigated the junction heating effects originating from quasi-particle trapping in the Nb electrodes embedded in NbTiN circuits by varying the volume of the electrodes. It was confirmed that current-voltage curves of Nb/AlN/Nb tunnel junctions with thick (~200 nm) counter electrodes contacting NbTiN wirings showed higher gap voltages as well as reduced back-bending than those with thin (~50 nm) electrodes. Making use of these findings, our designed SIS mixers employing Nb/AlN/Nb junctions with a current density of 15 kA/cm2and all-NbTiN tuning circuits may cover the Band 10 with good sensitivity.