Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Low-noise waveguide SIS mixer with NbN/AlN/NbN tunnel junctions tuned by an NbN/MgO/NbTiN microstrip circuit

Masanori Takeda, Wenlei Shan, Takafumi Kojima, Shingo Saito, M. Kroug, Yoshinori Uzawa, Zhen Wang

Published Jun 10, 2009• 10 citations
Publisher

Abstract

The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.

DOI
10.1088/0953-2048/22/7/075015

Related papers

Mixing Properties of NbN-Based SIS Mixers With NbTiN Wirings

Mahoto Takeda, Wenlei Shan, Takafumi Kojima +5 more

We report on the mixing properties of waveguide SIS mixers with epitaxial NbN/AlN/NbN junctions and NbN/SiO2/NbTiN microstrips on MgO substrates. The superconducting transition temperature and 20-K resistivity of NbTiN film on the SiO2dielectric were 14.7 K and 175 muOmega cm, respectively. The junction tuning circuit was composed of an NbN/SiO2/NbTiN microstrip and two parallel-connected NbN/AlN/NbN junctions 0.9 mum in diameter. The critical current density and normal-state resistance of the fabricated NbN junction were 13 kA/cm2and 22 Omega, respectively. The heterodyne response was measured using 295- and 77-K blackbody sources, a local oscillator (LO) source, and a 25-mum-thick Kapton film as a beam splitter. An intermediate frequency (IF) amplifier with a bandwidth of 4-12 GHz was used in the measurements. The receiver noise temperature corrected for losses in the beam splitter and in the vacuum window of the cryocooler was 370 K at 860 GHz and was comparable to that of all-NbN mixes with NbN/MgO/NbN microstrips.

IEEE Transactions on Applied Superconductivity•May 27, 2009•10 citations

Low-noise submillimeter-wave NbTiN superconducting tunnel junction mixers

Jonathan H. Kawamura, Jian Chen, David Miller +5 more

We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.

Applied Physics Letters•Dec 20, 1999•81 citations

Development of a waveguide NbN-based SIS mixer in the 900-GHz band

Mahoto Takeda, Yoshinori Uzawa, Zhen Wang +2 more

We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

Terahertz NbN/AlN/NbN mixers with Al/SiO/NbN microstrip tuning circuits

Yoshinori Uzawa, Zhen Wang, Akira Kawakami

We have developed a low-noise quasioptical NbN/AlN/NbN superconductor-insulator-superconductor (SIS) mixer that operates at terahertz frequencies. The mixer uses a MgO hyperhemispherical lens with an antireflection cap, a single-crystal NbN log-periodic antenna, and two-junction tuning circuits which employ Al/SiO/NbN microstriplines. The NbN/AlN/NbN junction size was about 0.9 μm in diameter, and the current density was about 45 kA/cm2. The frequency dependence of the receiver noise temperature was investigated by using an optically pumped far-infrared laser and a backward-wave oscillator as a local oscillator at several frequencies from 670 to 1082 GHz. The experimental results showed that the center frequency was around 800 GHz, and the receiver noise temperature measured by the standard Y-factor method was 457 K (DSB) at 783 GHz including a 9-μm-thick Mylar beam splitter loss and other optical losses at the physical bath temperature of 4.2 K. This is the first SIS mixer based on NbN with low-noise performance (12hν/kB) above the gap frequency of Nb.

Applied Physics Letters•Aug 3, 1998•44 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations
The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.
We report on the mixing properties of waveguide SIS mixers with epitaxial NbN/AlN/NbN junctions and NbN/SiO2/NbTiN microstrips on MgO substrates. The superconducting transition temperature and 20-K resistivity of NbTiN film on the SiO2dielectric were 14.7 K and 175 muOmega cm, respectively. The junction tuning circuit was composed of an NbN/SiO2/NbTiN microstrip and two parallel-connected NbN/AlN/NbN junctions 0.9 mum in diameter. The critical current density and normal-state resistance of the fabricated NbN junction were 13 kA/cm2and 22 Omega, respectively. The heterodyne response was measured using 295- and 77-K blackbody sources, a local oscillator (LO) source, and a 25-mum-thick Kapton film as a beam splitter. An intermediate frequency (IF) amplifier with a bandwidth of 4-12 GHz was used in the measurements. The receiver noise temperature corrected for losses in the beam splitter and in the vacuum window of the cryocooler was 370 K at 860 GHz and was comparable to that of all-NbN mixes with NbN/MgO/NbN microstrips.
We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.
We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
We have developed a low-noise quasioptical NbN/AlN/NbN superconductor-insulator-superconductor (SIS) mixer that operates at terahertz frequencies. The mixer uses a MgO hyperhemispherical lens with an antireflection cap, a single-crystal NbN log-periodic antenna, and two-junction tuning circuits which employ Al/SiO/NbN microstriplines. The NbN/AlN/NbN junction size was about 0.9 μm in diameter, and the current density was about 45 kA/cm2. The frequency dependence of the receiver noise temperature was investigated by using an optically pumped far-infrared laser and a backward-wave oscillator as a local oscillator at several frequencies from 670 to 1082 GHz. The experimental results showed that the center frequency was around 800 GHz, and the receiver noise temperature measured by the standard Y-factor method was 457 K (DSB) at 783 GHz including a 9-μm-thick Mylar beam splitter loss and other optical losses at the physical bath temperature of 4.2 K. This is the first SIS mixer based on NbN with low-noise performance (12hν/kB) above the gap frequency of Nb.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.