Applied Physics Letters

Ultra-low-noise tunnel junction dc SQUID with a tightly coupled planar input coil

M. B. Ketchen, J. M. Jaycox

Published Apr 15, 1982• 248 citations

Abstract

We present a new superconducting quantum interference device (SQUID) that combines ultra-low-noise performance with tight coupling to a useable input coil. The inductive loop of the SQUID consists of a superconducting square washer that is slit in a low inductance fashion from its central hole to an outside edge where two Josephson tunnel junctions are incorporated. The inductance of the SQUID is about 90 pH, and each junction has a critical current of 15 μA and a resistive shunt of 4.5 Ω. The 190-nH input coil is a planar spiral of 50 turns situated immediately above the washer and coupled to the SQUID with a coupling constant k2 of 0.86. The SQUID has a minimum coupled energy sensitivity of 19h at 4.2 K and 8h at 1.5 K, in good agreement with theory. The crossover between white and low frequency noise occurs at ∼250 Hz.

DOI: 10.1063/1.93210

Related papers

An ultra-low-noise tunnel junction dc SQUID

M. B. Ketchen, Richard F. Voss

The design, fabrication, and noise properties of an ultra-low-noise tunnel junction dc SQUID (superconducting quantum interference device) are presented. The two resistively shunted Pb-alloy tunnel junctions are each 3.6 μm diam. The SQUID has an inductance L of ≈11 pH, a critical current per junction, I0 of ≈100 μA, and a resistance per shunt R of ≈2 Ω. At 2.3 K, eI0R≈kBT, and simple theory predicts that the minimum intrinsic energy sensitivity should be ≈2h. The actual minimum value of the measured high-frequency (70 kHz) flux noise at 4.2 K is φn=1.3×10−7φ0 Hz−1/2. This corresponds to an intrinsic energy sensitivity, φ2n/2L, of 3.2×10−33 J Hz−1 or 5h. Lowering the bath temperature to 1.8 K gave no improvement in performance.

Applied Physics LettersNov 15, 197961 citations

A coupled DC SQUID with low 1/f noise

Heikki Seppä, M. Kiviranta, Alexandre Satrapinski +3 more

A low-noise coupled DC superconducting quantum interference device (SQUID) especially optimized for low frequency is discussed. Using large Josephson junctions and a low loop inductance the contribution of the critical current fluctuation to 1/f noise can be minimized. To minimize the inductance the Josephson junctions are placed in the center of the washer close to the SQUID loop. A scaled-up copper model of the SQUID and the signal coil is used to analyze the impedance of the SQUID loop affected by the signal coil. An equivalent circuit model describing the effective inductance of the SQUID loop as a function of the frequency is used to design appropriate damping of the resonances. The DC SQUID characteristics are smooth and the noise performance of the SQUID does not markedly suffer from resonances. The contribution of the 1/f noise at 1 Hz is found to be about 5*10/sup -7/ Phi /sub 0// square root Hz.>

IEEE Transactions on Applied SuperconductivityMar 1, 199325 citations

Low noise niobium dc SQUID with a planar input coil

V. J. de Waal, P. van den Hamer, T. M. Klapwijk

A practical all-niobium dc superconducting quantum interference device (SQUID) with a niobium spiral input coil has been developed. The SQUID utilizes submicron Josephson junctions. The best intrinsic energy resolution obtained with a 1-nH SQUID is 4×10−32 J/Hz. A 20-turn 1.2-μH input coil is coupled to a 2.3-nH SQUID with an efficiency of 0.5. The energy resolution with respect to the coil is 1×10−30 J/Hz.

Applied Physics LettersFeb 15, 198312 citations

Sub-μm linewidth input coils for low T c integrated thin-film dc superconducting quantum interference devices

M. B. Ketchen, Kevin G. Stawiasz, Dale J. Pearson +6 more

We have, for the first time, demonstrated integrated dc superconducting quantum interference devices (SQUIDs) with input coils of linewidth down to 0.5 μm. The SQUID inductance L consists of a single octagonal washer or two or four such washers configured in parallel. The input coil of inductance Li, which couples to L with a mutual inductance of Mi, consists of fine-line octagonal spiral(s) fabricated in close proximity to the washer(s). For a two-washer SQUID with twin 80-turn, 0.5 μm spirals, Li=2.5 μH, Mi=12.7 nH, L=109 pH, and the coupling constant k2=0.85. This entire device occupies an area of less than 0.2 mm2.

Applied Physics LettersJul 20, 199223 citations

Effect of an input coil microwave resonance on dynamics and noise properties of a dc superconducting quantum interference device operating close to the hysteretic mode

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.

Review of Scientific InstrumentsMar 1, 19999 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied SuperconductivityJun 1, 19991 citation