Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Effect of an input coil microwave resonance on dynamics and noise properties of a dc superconducting quantum interference device operating close to the hysteretic mode

Vladimir Polushkin, D. Glowacka, R. Hart, John M. Lumley

Published Mar 1, 1999• 9 citations
Publisher

Abstract

The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.

DOI
10.1063/1.1149656

Related papers

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation

Effect of parasitic capacitance and inductance on the dynamics and noise of dc superconducting quantum interference devices

Tapani Ryhänen, Heikki Seppä, R. Cantor

Practical thin-film dc superconducting quantum interference devices (SQUIDs) are often built with an integrated input coil which leads to the formation of various parasitic elements. We have designed and fabricated several square washer-shaped dc SQUID test devices with various amounts of parasitic capacitance formed by covering the washer slits with superconducting coverplates of various widths. In the simplest approximation, the parasitic capacitance Cp appears entirely across the Josephson junctions; in a better approximation, Cp divides the total inductance into two parts, an effective SQUID loop inductance L and a small parasitic inductance Lp. For both models, noise-free and noise-rounded current-voltage and voltage-flux characteristics are calculated for various values of the ratios L/Lp and Cp/C, where C is the Josephson junction capacitance. The SQUID dynamics are significantly affected by Cp and Lp. The energy resolution ε at first deteriorates with increasing Cp for Cp/C ≲ 2, but as Cp/C becomes large, ε improves to less than twice the value for Cp/C ≊ 0. The optimal points of operation for large Cp, however, are found at voltages above the low-frequency resonance determined by L and Cp where the flux-to-voltage transfer function is low. Furthermore, for devices with Cp/C ≫ 1 and Lp≠0, the double-loop geometry leads to an additional resonance determined by Lp and C that appears at high frequencies. The energy resolution inside this high-frequency resonance is nearly independent of Cp and comparable to the energy resolution of a device having the same total inductance but with Cp/C ≪ 1. Extensive noise mappings on several different test devices have been carried out using a computer-controlled measurement system. The measured characteristics and noise performance are shown to be in good agreement with the simulations.

Journal of Applied Physics•Jun 15, 1992•32 citations

Array of Superconducting Quantum Interference Devices with Multiturn Input Coil

T. Morooka, Hiroaki Myoren, S. Takada +1 more

Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.

Japanese Journal of Applied Physics•May 1, 2004•3 citations

Ultra-low-noise tunnel junction dc SQUID with a tightly coupled planar input coil

M. B. Ketchen, J. M. Jaycox

We present a new superconducting quantum interference device (SQUID) that combines ultra-low-noise performance with tight coupling to a useable input coil. The inductive loop of the SQUID consists of a superconducting square washer that is slit in a low inductance fashion from its central hole to an outside edge where two Josephson tunnel junctions are incorporated. The inductance of the SQUID is about 90 pH, and each junction has a critical current of 15 μA and a resistive shunt of 4.5 Ω. The 190-nH input coil is a planar spiral of 50 turns situated immediately above the washer and coupled to the SQUID with a coupling constant k2 of 0.86. The SQUID has a minimum coupled energy sensitivity of 19h at 4.2 K and 8h at 1.5 K, in good agreement with theory. The crossover between white and low frequency noise occurs at ∼250 Hz.

Applied Physics Letters•Apr 15, 1982•248 citations

Dependence of SQUID Intrinsic Flux Noise on Stewart–McCumber Parameter $\beta_{c}$ of Josephson Junction

Hai Wang, Yongliang Wang, Xiangyan Kong +3 more

It is known that three superconducting quantum interference device (SQUID) parameters, namely, the intrinsic flux noise δΦs, the flux-to-voltage transfer coefficient ∂V/∂Φ, and the dynamic resistance Rd, increase with increasing the Stewart- McCumber parameter βcof Josephson junction. It is very difficult to obtain the low values of δΦsfor a strongly damped SQUID due to its small ∂V/∂Φ. In this paper, we employ a two-stage scheme (TSS) to measure δΦsdirectly. Here, we use single chip readout electronics and a weakly damped SQUID with a βcof flux noise of the readout-SQUID system is about 4.8 μΦ0/√Hz 1.2, both acting as a readout-SQUID system (a preamplifier). The with a corner frequency of about 10 Hz. The front-end SQUID is coupled to the readout SQUID via the input coil with a mutual inductance of Mi. In our experiment, the flux gain for a readout SQUID, i.e., GΦ= Mi× (∂I/∂Φ)front-endis adjusted to be 20. Using the TSS, we measured δΦswith different βcchanging from 0.3 to 13.5 and found δΦsincreasing from 1.0 to 5.0 μΦ0/√Hz. We also discussed the relations between Ls, βc, and δΦsquantitatively. Finally, we proposed designing a suitable βcto match the preamplifier in a direct readout scheme to simplify a SQUID measurement system.

IEEE Transactions on Applied Superconductivity•May 12, 2016•4 citations

Low noise niobium dc SQUID with a planar input coil

V. J. de Waal, P. van den Hamer, T. M. Klapwijk

A practical all-niobium dc superconducting quantum interference device (SQUID) with a niobium spiral input coil has been developed. The SQUID utilizes submicron Josephson junctions. The best intrinsic energy resolution obtained with a 1-nH SQUID is 4×10−32 J/Hz. A 20-turn 1.2-μH input coil is coupled to a 2.3-nH SQUID with an efficiency of 0.5. The energy resolution with respect to the coil is 1×10−30 J/Hz.

Applied Physics Letters•Feb 15, 1983•12 citations
The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
Practical thin-film dc superconducting quantum interference devices (SQUIDs) are often built with an integrated input coil which leads to the formation of various parasitic elements. We have designed and fabricated several square washer-shaped dc SQUID test devices with various amounts of parasitic capacitance formed by covering the washer slits with superconducting coverplates of various widths. In the simplest approximation, the parasitic capacitance Cp appears entirely across the Josephson junctions; in a better approximation, Cp divides the total inductance into two parts, an effective SQUID loop inductance L and a small parasitic inductance Lp. For both models, noise-free and noise-rounded current-voltage and voltage-flux characteristics are calculated for various values of the ratios L/Lp and Cp/C, where C is the Josephson junction capacitance. The SQUID dynamics are significantly affected by Cp and Lp. The energy resolution ε at first deteriorates with increasing Cp for Cp/C ≲ 2, but as Cp/C becomes large, ε improves to less than twice the value for Cp/C ≊ 0. The optimal points of operation for large Cp, however, are found at voltages above the low-frequency resonance determined by L and Cp where the flux-to-voltage transfer function is low. Furthermore, for devices with Cp/C ≫ 1 and Lp≠0, the double-loop geometry leads to an additional resonance determined by Lp and C that appears at high frequencies. The energy resolution inside this high-frequency resonance is nearly independent of Cp and comparable to the energy resolution of a device having the same total inductance but with Cp/C ≪ 1. Extensive noise mappings on several different test devices have been carried out using a computer-controlled measurement system. The measured characteristics and noise performance are shown to be in good agreement with the simulations.
Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.
We present a new superconducting quantum interference device (SQUID) that combines ultra-low-noise performance with tight coupling to a useable input coil. The inductive loop of the SQUID consists of a superconducting square washer that is slit in a low inductance fashion from its central hole to an outside edge where two Josephson tunnel junctions are incorporated. The inductance of the SQUID is about 90 pH, and each junction has a critical current of 15 μA and a resistive shunt of 4.5 Ω. The 190-nH input coil is a planar spiral of 50 turns situated immediately above the washer and coupled to the SQUID with a coupling constant k2 of 0.86. The SQUID has a minimum coupled energy sensitivity of 19h at 4.2 K and 8h at 1.5 K, in good agreement with theory. The crossover between white and low frequency noise occurs at ∼250 Hz.
Dependence of SQUID Intrinsic Flux Noise on Stewart–McCumber Parameter βc\beta_{c}βc​ of Josephson Junction
It is known that three superconducting quantum interference device (SQUID) parameters, namely, the intrinsic flux noise δΦs, the flux-to-voltage transfer coefficient ∂V/∂Φ, and the dynamic resistance Rd, increase with increasing the Stewart- McCumber parameter βcof Josephson junction. It is very difficult to obtain the low values of δΦsfor a strongly damped SQUID due to its small ∂V/∂Φ. In this paper, we employ a two-stage scheme (TSS) to measure δΦsdirectly. Here, we use single chip readout electronics and a weakly damped SQUID with a βcof flux noise of the readout-SQUID system is about 4.8 μΦ0/√Hz 1.2, both acting as a readout-SQUID system (a preamplifier). The with a corner frequency of about 10 Hz. The front-end SQUID is coupled to the readout SQUID via the input coil with a mutual inductance of Mi. In our experiment, the flux gain for a readout SQUID, i.e., GΦ= Mi× (∂I/∂Φ)front-endis adjusted to be 20. Using the TSS, we measured δΦswith different βcchanging from 0.3 to 13.5 and found δΦsincreasing from 1.0 to 5.0 μΦ0/√Hz. We also discussed the relations between Ls, βc, and δΦsquantitatively. Finally, we proposed designing a suitable βcto match the preamplifier in a direct readout scheme to simplify a SQUID measurement system.