IEEE Transactions on Applied Superconductivity

A coupled DC SQUID with low 1/f noise

Heikki Seppä, M. Kiviranta, Alexandre Satrapinski, Leif Grönberg, Jorma Salmi, Ilkka Suni

Published Mar 1, 1993• 25 citations

Abstract

A low-noise coupled DC superconducting quantum interference device (SQUID) especially optimized for low frequency is discussed. Using large Josephson junctions and a low loop inductance the contribution of the critical current fluctuation to 1/f noise can be minimized. To minimize the inductance the Josephson junctions are placed in the center of the washer close to the SQUID loop. A scaled-up copper model of the SQUID and the signal coil is used to analyze the impedance of the SQUID loop affected by the signal coil. An equivalent circuit model describing the effective inductance of the SQUID loop as a function of the frequency is used to design appropriate damping of the resonances. The DC SQUID characteristics are smooth and the noise performance of the SQUID does not markedly suffer from resonances. The contribution of the 1/f noise at 1 Hz is found to be about 5*10/sup -7/ Phi /sub 0// square root Hz.>

DOI: 10.1109/77.233329

Related papers

Ultra-low-noise tunnel junction dc SQUID with a tightly coupled planar input coil

M. B. Ketchen, J. M. Jaycox

We present a new superconducting quantum interference device (SQUID) that combines ultra-low-noise performance with tight coupling to a useable input coil. The inductive loop of the SQUID consists of a superconducting square washer that is slit in a low inductance fashion from its central hole to an outside edge where two Josephson tunnel junctions are incorporated. The inductance of the SQUID is about 90 pH, and each junction has a critical current of 15 μA and a resistive shunt of 4.5 Ω. The 190-nH input coil is a planar spiral of 50 turns situated immediately above the washer and coupled to the SQUID with a coupling constant k2 of 0.86. The SQUID has a minimum coupled energy sensitivity of 19h at 4.2 K and 8h at 1.5 K, in good agreement with theory. The crossover between white and low frequency noise occurs at ∼250 Hz.

Applied Physics LettersApr 15, 1982248 citations

Optimization of a Low-Tc DC SQUID Amplifier With Tightly Coupled Input Coils

J. Pleikies, O. Usenko, G. Frossati +1 more

We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.

IEEE Transactions on Applied SuperconductivityJun 1, 20096 citations

Performance of dc SQUIDs with resistively shunted inductance

Vittorio Foglietti, W. J. Gallagher, M. B. Ketchen +3 more

We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.

Applied Physics LettersOct 2, 198945 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied SuperconductivityJun 1, 19991 citation

Design and optimization of DC SQUIDs fabricated using a simplified four-level process

R. Cantor, Tapani Ryhänen, D. Drung +2 more

An optimization procedure is presented which is used to design two types of ultralow-noise DC superconducting quantum interference devices (SQUIDs) with integrated flux coupling circuits, a magnetometer, and a gradiometer. Essential to this design approach is the reduction of the parasitic capacitance, the choice of a layout which moves the input coil resonances well away from the desired operating frequency of the SQUID, and the proper damping of these resonances. It is shown that both the microwave and LC resonances can be damped in a nearly noise-free manner by placing all RC shunt in parallel with the input coil. This leads to smooth voltage-flux modulation characteristics and significantly improved noise performance. A simple, four-level Nb-Si/sub x/N/sub y/-Nb Josephson junction technology for device fabrication is described. White flux noise levels of 5*10/sup -7/ Phi /sub 0// square root Hz for the magnetometer and 7.9*10/sup -7/ Phi /sub 0// square root Hz for the gradiometer were measured. The corresponding uncoupled energy resolutions are 100 h and 130 h, respectively. The 1/f noise of the magnetometer at 1 Hz is less than 4*10/sup -6/ Phi /sub 0// square root Hz.

IEEE Transactions on MagneticsMar 1, 199135 citations

Origin of 1/f noise in Y1Ba2Cu3O7−x step-edge dc SQUIDs

Dirk Grundler, Rainer Eckart, Bernd R. David +1 more

We have fabricated Y1Ba2Cu3O7−x step-edge junction dc superconducting quantum interference devices (SQUIDs) and characterized their noise performance. The current-voltage characteristics of our SQUIDs are of resistively shunted junction type with critical current densities jc of about 104 A/cm2 and maximum flux to voltage transfer functions δV/δΦ of 20 μV/Φ0 at 77 K. We compare model predictions for 1/f noise in dc SQUIDs with experimental data and show that the frequency dependent noise in our devices results from critical current fluctuations of the Josephson junctions. A bias current reversing technique is effective in suppressing this noise contribution. A flux noise Φn of 80 μΦ0/Hz1/2 at 1 Hz and 77 K was measured on a dc SQUID with an inductance Ls of 60 pH.

Applied Physics LettersApr 26, 199324 citations