Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Electronics

SIS Junctions for Millimeter and Submillimeter Wave Mixers

Takashi Noguchi, Toyoaki Suzuki, Tomonori Tamura

Published Jan 1, 2012• 2 citations
Publisher

Abstract

We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.

DOI
10.1587/transele.e95.c.320

Related papers

Fabrication and characterization of high current-density, submicron, NbN/MgO/NbN tunnel junctions

Jeff A. Stern, Henry George LeDuc, A. Judas

At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.

•Jan 1, 1992•12 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

Very high-current-density Nb/AlN/Nb tunnel junctions for low-noise submillimeter mixers

Jonathan H. Kawamura, David Miller, Jian Chen +4 more

We have fabricated and tested submillimeter-wave superconductor–insulator–superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc≈30 kA cm−2). The junctions have low-resistance-area products (RNA≈5.6 Ω μm2), good subgap-to-normal resistance ratios Rsg/RN≈10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that ωRNC=1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX=110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits.

Applied Physics Letters•Apr 10, 2000•55 citations

Noise performance of a 200–280 GHz mixer with Nb-AlN-NbN superconducting tunnel junctions

Boliang Liu, Dong Liu, Ming Yao +6 more

Superconductor–insulator–superconductor (SIS) mixers remain the choice of heterodyne mixers for single-dish telescopes and interferometers at millimeter and submillimeter wavelengths. Compared with conventional Nb/AlOx/Nb superconducting tunnel junctions, Nb/AlN/NbN ones have larger gap voltage and may reach critical-current density beyond 10kA/cm2, which are both of particularly interest in developing broadband SIS mixers. Here we report on the design and measurement of an SIS mixer based on Nb/AlN/NbN parallel connected twin junctions (PCTJ) incorporating NbTiN/SiO2/Al microstrip circuit. The junctions have a gap voltage of 3.18mV and a critical-current density of 15kA/cm2. The measured receiver noise temperature reach 5hν/kB among 200-260GHz band, and the mixer’s fractional bandwidth is about 40% centered at 230GHz.

Infrared, Millimeter-Wave, and Terahertz Technologies•Dec 16, 2022•0 citations

Quasi-optical submillimeter-wave SIS mixers with NbN/A1N/NbN tunnel junctions

Yoshinori Uzawa, Zhen Wang, Akira Kawakami

We report on low-noise heterodyne mixing with NbN/A1N/NbN tunnel junctions in the submillimeter-wave region for the first time. The receiver consists of the quasi-optical NbN SIS mixer with an integrated tuning circuit in which a radial short stub tuner is incorporated to resonate out the junction capacitance for RF matching and a balanced IF circuit for broadband IF matching. The prepared NbN SIS junction has a current density of 20 kA/cm 2 and is about 1 I1111 in diameter, supplying a small coC JRN product (o)CJRN = 3 at 300 GHz). The junctions showed good dc I-V characteristics, excellent submillimeter-wave responses and sensitive heterodyne mixing responses. From 254 to 350 GHz the average receiver noise temperature measured using by the standard Y-factor method was about 250 K (DSB) at 5 K. The lowest receiver noise temperature, 200 K (DSB), was obtained at around 303 GHz. Comparing NbN/A1N/NbN and Nb/A10x/Nb tunnel junction performance with the same tuning circuit showed that the frequency dependence of the receiver noise temperature agreed well in the two receivers. These results suggest that our well-controlled NbN SIS junctions can be used for terahertz mixer elements instead of Nb SIS junctions.

•Mar 1, 1996•2 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology - art. no. 684013

Jing Li, Takeda Masanon, Zhen Wang

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.

•Jan 1, 2008•0 citations
We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.
At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
We have fabricated and tested submillimeter-wave superconductor–insulator–superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc≈30 kA cm−2). The junctions have low-resistance-area products (RNA≈5.6 Ω μm2), good subgap-to-normal resistance ratios Rsg/RN≈10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that ωRNC=1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX=110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits.
Superconductor–insulator–superconductor (SIS) mixers remain the choice of heterodyne mixers for single-dish telescopes and interferometers at millimeter and submillimeter wavelengths. Compared with conventional Nb/AlOx/Nb superconducting tunnel junctions, Nb/AlN/NbN ones have larger gap voltage and may reach critical-current density beyond 10kA/cm2, which are both of particularly interest in developing broadband SIS mixers. Here we report on the design and measurement of an SIS mixer based on Nb/AlN/NbN parallel connected twin junctions (PCTJ) incorporating NbTiN/SiO2/Al microstrip circuit. The junctions have a gap voltage of 3.18mV and a critical-current density of 15kA/cm2. The measured receiver noise temperature reach 5hν/kB among 200-260GHz band, and the mixer’s fractional bandwidth is about 40% centered at 230GHz.
We report on low-noise heterodyne mixing with NbN/A1N/NbN tunnel junctions in the submillimeter-wave region for the first time. The receiver consists of the quasi-optical NbN SIS mixer with an integrated tuning circuit in which a radial short stub tuner is incorporated to resonate out the junction capacitance for RF matching and a balanced IF circuit for broadband IF matching. The prepared NbN SIS junction has a current density of 20 kA/cm 2 and is about 1 I1111 in diameter, supplying a small coC JRN product (o)CJRN = 3 at 300 GHz). The junctions showed good dc I-V characteristics, excellent submillimeter-wave responses and sensitive heterodyne mixing responses. From 254 to 350 GHz the average receiver noise temperature measured using by the standard Y-factor method was about 250 K (DSB) at 5 K. The lowest receiver noise temperature, 200 K (DSB), was obtained at around 303 GHz. Comparing NbN/A1N/NbN and Nb/A10x/Nb tunnel junction performance with the same tuning circuit showed that the frequency dependence of the receiver noise temperature agreed well in the two receivers. These results suggest that our well-controlled NbN SIS junctions can be used for terahertz mixer elements instead of Nb SIS junctions.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.