Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Fabrication and characterization of high current-density, submicron, NbN/MgO/NbN tunnel junctions

Jeff A. Stern, Henry George LeDuc, A. Judas

Published Jan 1, 1992• 12 citations
OpenAlex

Abstract

At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.

Related papers

Fabrication and testing of NbN/MgO/NbN tunnel junctions for use as high-frequency heterodyne detectors

Jeffrey A. Stern

This thesis describes the development and testing of NbN/MgO/NbN tunnel junctions for use as superconductor-insulator-superconductor (SIS) mixers. SIS mixers are the most sensitive heterodyne detectors in the millimeter wavelength region. Most SIS mixers use Pb alloy tunnel junction. These tunnel junctions have several problems associated with the soft nature of Pb and its low superconducting transition temperature. NbN-based tunnel junctions are being developed to overcome these difficulties. These devices are intended to be used as mixers at millimeter and submillimeter wavelengths. This thesis describes the fabrication process involved in making NbN junctions, and the results of measurements on these devices. The purpose of these measurements is to determine the future possibilities of NbN tunnel junctions as high-frequency mixers. The first chapter is an introduction to SIS mixers and explains how tunnel junction properties affect mixer performance. The basic theory of tunneling and mixing in SIS mixers is first presented. A description of quantum mixer theory is included in this presentation. This theory makes several interesting predictions that cannot be explained using classical theories. This is followed by a description of how real SIS tunnel junctions differ from ideal junctions. The physical origin of these differences is discussed, along with how they affect SIS mixer performance. Finally, the advantages and disadvantages of the various superconducting materials available are discussed. The decision to develop NbN devices is based on these material properties. The second chapter describes the methods used to fabricate small-area NbN/MgO/NbN tunnel junctions. The chapter begins with a description of the various methods that have been used to deposit NbN films. Reactive magnetron sputtering is chosen as the best method for tunnel junction fabrication. Details on the vacuum systems and the methods used for depositing superconducting NbN are discussed. Next, the process used for depositing junction trilayers (NbN/MgO/NbN) is described. The probable growth mode of MgO on NbN is presented. The importance of this growth mode to the junction quality is explained in some detail. Next, standard junction processing steps are reported. The details and limitations of each step are put forth. The standard process allows for the fabrication of 1 [square micron] tunnel junctions. Finally, this chapter discusses several methods of fabaricating submicron junctions that are being pursued. The status of this work is given. The third chapter describes the characterization of NbN films and NbN/Mg0/NbN tunnel junctions. Film properties are described first. The correlation of these properties to deposition conditions is discussed in some detail. Next, values for the various features of the I-V characteristic are given; typical and exceptional values are noted. How these features limit mixer results is described in detail. Several important device attributes were measured using superconducting-quantum-interference-devices (SQUIDs). These attributes are the junction's specific capacitance and the film's magnetic penetration depth. The theory and results of measuring specific capacitance and penetration depth are presented. Following the SQUID results is a large section on RP testing. Mixer tests were made at 205 GHz. The receiver design used, integral inductive tuning circuit used and results are discussed. These results are well understood, with the exception of the temperature dependence of the mixer performance. Finally, measurements of the uniformity of many junctions on a single wafer are presented. The importance of junction uniformity is also described. The final chapter discusses the ultimate limits on NbN mixers, and tells what future work must be done to achieve these limits. The primary high-frequency limit on NbN junctions is the capacitance of NbN/MgO/NbN junctions. The limit imposed by the junction capacitance and circuits used to tune out this capacitance are discussed. Also, the low-frequency limits on NbN junctions are discussed. The status of submicron devices is presented. Junction area is the most immediate limitation on NbN mixer results. The possibility of using other barrier materials to increase the RC speed of NbN junctions is presented. Finally, the possibility of operating NbN junctions at temperatures above 4.2 K is discussed.

•Jan 1, 1991•0 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

High-current-density small-area SIS junctions for high-frequency radio astronomy

Eric E. Bloemhof

At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area $AP 0.5 micrometers 2 and critical current density $AP 10,000 Amp/cm2.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 2, 1994•1 citation

SIS Junctions for Millimeter and Submillimeter Wave Mixers

Takashi Noguchi, Toyoaki Suzuki, Tomonori Tamura

We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.

IEICE Transactions on Electronics•Jan 1, 2012•2 citations

NbN/MgO/NbN SIS tunnel junctions for submm wave mixers

J. A. Stern, B. D. Hunt, Henry George LeDuc +4 more

The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>

IEEE Transactions on Magnetics•Mar 1, 1989•17 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology - art. no. 684013

Jing Li, Takeda Masanon, Zhen Wang

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.

•Jan 1, 2008•0 citations
At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.
This thesis describes the development and testing of NbN/MgO/NbN tunnel junctions for use as superconductor-insulator-superconductor (SIS) mixers. SIS mixers are the most sensitive heterodyne detectors in the millimeter wavelength region. Most SIS mixers use Pb alloy tunnel junction. These tunnel junctions have several problems associated with the soft nature of Pb and its low superconducting transition temperature. NbN-based tunnel junctions are being developed to overcome these difficulties. These devices are intended to be used as mixers at millimeter and submillimeter wavelengths. This thesis describes the fabrication process involved in making NbN junctions, and the results of measurements on these devices. The purpose of these measurements is to determine the future possibilities of NbN tunnel junctions as high-frequency mixers. The first chapter is an introduction to SIS mixers and explains how tunnel junction properties affect mixer performance. The basic theory of tunneling and mixing in SIS mixers is first presented. A description of quantum mixer theory is included in this presentation. This theory makes several interesting predictions that cannot be explained using classical theories. This is followed by a description of how real SIS tunnel junctions differ from ideal junctions. The physical origin of these differences is discussed, along with how they affect SIS mixer performance. Finally, the advantages and disadvantages of the various superconducting materials available are discussed. The decision to develop NbN devices is based on these material properties. The second chapter describes the methods used to fabricate small-area NbN/MgO/NbN tunnel junctions. The chapter begins with a description of the various methods that have been used to deposit NbN films. Reactive magnetron sputtering is chosen as the best method for tunnel junction fabrication. Details on the vacuum systems and the methods used for depositing superconducting NbN are discussed. Next, the process used for depositing junction trilayers (NbN/MgO/NbN) is described. The probable growth mode of MgO on NbN is presented. The importance of this growth mode to the junction quality is explained in some detail. Next, standard junction processing steps are reported. The details and limitations of each step are put forth. The standard process allows for the fabrication of 1 [square micron] tunnel junctions. Finally, this chapter discusses several methods of fabaricating submicron junctions that are being pursued. The status of this work is given. The third chapter describes the characterization of NbN films and NbN/Mg0/NbN tunnel junctions. Film properties are described first. The correlation of these properties to deposition conditions is discussed in some detail. Next, values for the various features of the I-V characteristic are given; typical and exceptional values are noted. How these features limit mixer results is described in detail. Several important device attributes were measured using superconducting-quantum-interference-devices (SQUIDs). These attributes are the junction's specific capacitance and the film's magnetic penetration depth. The theory and results of measuring specific capacitance and penetration depth are presented. Following the SQUID results is a large section on RP testing. Mixer tests were made at 205 GHz. The receiver design used, integral inductive tuning circuit used and results are discussed. These results are well understood, with the exception of the temperature dependence of the mixer performance. Finally, measurements of the uniformity of many junctions on a single wafer are presented. The importance of junction uniformity is also described. The final chapter discusses the ultimate limits on NbN mixers, and tells what future work must be done to achieve these limits. The primary high-frequency limit on NbN junctions is the capacitance of NbN/MgO/NbN junctions. The limit imposed by the junction capacitance and circuits used to tune out this capacitance are discussed. Also, the low-frequency limits on NbN junctions are discussed. The status of submicron devices is presented. Junction area is the most immediate limitation on NbN mixer results. The possibility of using other barrier materials to increase the RC speed of NbN junctions is presented. Finally, the possibility of operating NbN junctions at temperatures above 4.2 K is discussed.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
At the Smithsonian Astrophysical Observatory, we have been developing expertise in the construction of high-frequency heterodyne receivers using SIS junctions as their first mixing elements. This research has been carried out in support of the Submillimeter Array (SMA), a radio interferometer soon to be built on Mauna Kea that will require multiple reciever systems at a number of bands between 177 GHz and 920 GHz. In this paper, we describe research on the fabrication of all-refractory SIS junctions. To be useful as high-frequency mixers, SIS junctions must have small area and high critical current density. At the lower SMA frequencies, Nb/Al-Oxide/Nb ahs proven to be an ideal material system, and optical photolithography has sufficient resolution for junction definition. At the higher frequencies, NbN/MgO/NbN may enjoy an advantage due to its larger energy gap, and electron-beam lithography may be necessary for defining junctions much smaller than one micron in size. We report good initial results for Nb/Al-Oxide/Nb junctions, fabricated using a self-aligned optical technique, with area $AP 0.5 micrometers 2 and critical current density $AP 10,000 Amp/cm2.
We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.
The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AIO(x)/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region.