Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2603.19142

High efficiency superconducting filterbank with impedance-defined resolution for millimeter-wave spectroscopy

Oliver B. Jeong, M. Piat, Aritoki Suzuki

Published Mar 19, 2026• 0 citations
arXivHTMLPDF

Abstract

We present a high efficiency, moderate resolution on-chip superconducting filterbank spectrometer designed for line intensity mapping and broadband wave-like dark matter searches. Existing implementations used by the millimeter-wave community rely on resistive feedline termination for standing wave mitigation which caps the per-channel efficiency $η_\mathrm{ch}$ at 50\% and utilize microstrip resonators which highly couple the resolving power $\mathcal{R}=ν/δν$ and $η_\mathrm{ch}$ to thin-film dielectric loss. The architecture presented in this paper addresses these limitations by eliminating the termination resistor and employing niobium coplanar waveguide resonators patterned directly on single-crystal silicon, which fixes the resonator's internal quality factor by the silicon substrate property rather than by the loss tangent of a deposited film. The resolving power is set by the impedance ratio between the resonator and feedline. Electromagnetic and circuit simulations of a ten-channel filterbank near 90~GHz at unity oversampling show $\mathcal{R}=1170$ and $η_\mathrm{ch}> 78\%$, with no significant trend in efficiency across channels. A ten-channel prototype, designed for $\mathcal{R}=92\pm5$ and $η_\mathrm{ch}=(81\pm3)\%$ over 90--106~GHz with a 560~nm interlayer based on simulations, was fabricated and optically characterized, yielding $\mathcal{R}=208\pm74$ and $η_\mathrm{ch}=(77\pm6)\%$. Measured $η_\mathrm{ch}$ well above the 50\% termination limit, together with demonstrated impedance tuning of $\mathcal{R}$, validate the design principles of this filterbank spectrometer and establishes a route to high-efficiency, high-resolution on-chip spectrometer arrays.

DOI
10.48550/arxiv.2603.19142

Related papers

Superconducting Coplanar Waveguide Filters for Submillimeter Wave On-Chip Filterbank Spectrometers

Akira Endo, S. J. C. Yates, Juan Bueno +6 more

We show the first experimental results which prove that superconducting NbTiN coplanar–waveguide resonators can achieve a loaded Q factor in excess of 800 in the 350 GHz band. These resonators can be used as narrow band pass filters for on-chip filter bank spectrometers for astronomy. Moreover, the low-loss coplanar waveguide technology provides an interesting alternative to microstrip lines for constructing large scale submillimeter wave electronics in general.

Journal of Low Temperature Physics•Mar 24, 2016•5 citations

The millimeter-wave properties of superconducting microstrip lines

Anastasios Vayonakis, Chiyan Luo, Henry George LeDuc +2 more

We have developed a novel technique for making high quality measurements of the millimeter-wave properties of superconducting thin-film microstrip transmission lines. Our experimental technique currently covers the 75–100 GHz band. The method is based on standing wave resonances in an open ended transmission line. We obtain information on the phase velocity and loss of the microstrip. Our data for Nb/SiO/Nb lines, taken at 4.2 K and 1.6 K, can be explained by a single set of physical parameters. Our preliminary conclusion is that the loss is dominated by the SiO dielectric, with a temperature-independent loss tangent of 5.3±0.5×10−3 for our samples.

AIP conference proceedings•Jan 1, 2002•15 citations

The Simulation and Design of an On-Chip Superconducting Millimetre Filter-Bank Spectrometer

G. Robson, Adam J. Anderson, Peter S. Barry +2 more

Abstract Superconducting on-chip filter banks provide a scalable, space saving solution to create imaging spectrometers at millimetre and submillimetre wavelengths. We present an easy to realise, lithographed superconducting filter design with a high tolerance to fabrication error. Using a capacitively coupled $$\lambda /2$$ λ / 2 microstrip resonator to define a narrow ( $$\lambda /\Delta \lambda = 300$$ λ / Δ λ = 300 ) spectral pass band, the filtered output of a given spectrometer channel directly connects to a lumped-element kinetic inductance detector. We show the tolerance analysis of our design, demonstrating $$<11\%$$ < 11 % change in filter quality factor to any one realistic fabrication error and a full filter-bank efficiency forecast to be 50% after accounting for fabrication errors and dielectric loss tangent.

arXiv:2111.04632•Journal of Low Temperature Physics•Jun 11, 2022•2 citations

A Compact Broadband Purcell Filter for Superconducting Quantum Circuits in a 3D Flip-Chip Architecture

Zhen Luo, Lea Richard, Ivan Tsitsilin +4 more

Fast and high-fidelity qubit readout requires strong coupling between the readout resonator and the feedline. However, such coupling unavoidably enhances qubit decay through the Purcell effect. We present a four-pole broadband Purcell filter implemented on a 3D flip-chip platform to overcome this trade-off. The filter provides a flat 1 GHz passband centered at 7.68 GHz and achieves more than 45 dB suppression at typical qubit frequencies. We demonstrate the filter's compatibility with multiplexed readout using a test chip that integrates six floating readout resonators strongly coupled within the passband. The chip is fabricated using a 150 nm Niobium (Nb) thin-film process and characterized at 20 mK in a cryogenic measurement setup. We also develop an analytical model that accurately captures the filter response and determines the resonance frequencies and external quality factors of the floating resonators directly from their physical geometry, enabling rapid circuit synthesis and design optimization. The proposed design is compact and fabrication-tolerant, making it a practical solution for large-scale superconducting quantum processors.

quant-pharXiv:2603.16693•IEEE Transactions on Microwave Theory and Techniques•Mar 18, 2026•0 citations

Fabrication Development for SPT-SLIM, a Superconducting Spectrometer for Line Intensity Mapping

T. Cecil, Chris Albert, Adam J. Anderson +18 more

Line Intensity Mapping (LIM) is a new observational technique that uses low-resolution observations of line emission to efficiently trace the large-scale structure of the Universe out to high redshift. Common mm/sub-mm emission lines are accessible from ground-based observatories, and the requirements on the detectors for LIM at mm-wavelengths are well matched to the capabilities of large-format arrays of superconducting sensors. We describe the development of an$ R$=$\lambda / \Delta \lambda = 300$on-chip superconducting filter-bank spectrometer covering the 120–180 GHz band for future mm-LIM experiments, focusing on SPT-SLIM, a pathfinder LIM instrument for the South Pole Telescope. Radiation is coupled from the telescope optical system to the spectrometer chip via an array of feedhorn-coupled orthomode transducers. Superconducting microstrip transmission lines then carry the signal to an array of channelizing half-wavelength resonators, and the output of each spectral channel is sensed by a lumped element kinetic inductance detector (leKID). Key areas of development include incorporating new low-loss dielectrics to improve both the achievable spectral resolution and optical efficiency and development of a robust fabrication process to create a galvanic connection between ultra-pure superconducting thin-films to realize multi-material (hybrid) leKIDs. We provide an overview of the spectrometer design, fabrication process, and prototype devices.

arXiv:2304.00973•IEEE Transactions on Applied Superconductivity•Apr 3, 2023•3 citations

Experimental demonstrations of high-Q superconducting coplanar waveguide resonators

HaiJie Li, YiWen Wang, LianFu Wei +6 more

We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.

arXiv:1304.3254•Chinese Science Bulletin•Jul 1, 2013•29 citations
We present a high efficiency, moderate resolution on-chip superconducting filterbank spectrometer designed for line intensity mapping and broadband wave-like dark matter searches. Existing implementations used by the millimeter-wave community rely on resistive feedline termination for standing wave mitigation which caps the per-channel efficiency ηchη_\mathrm{ch}ηch​ at 50% and utilize microstrip resonators which highly couple the resolving power R=ν/δν\mathcal{R}=ν/δνR=ν/δν and ηchη_\mathrm{ch}ηch​ to thin-film dielectric loss. The architecture presented in this paper addresses these limitations by eliminating the termination resistor and employing niobium coplanar waveguide resonators patterned directly on single-crystal silicon, which fixes the resonator's internal quality factor by the silicon substrate property rather than by the loss tangent of a deposited film. The resolving power is set by the impedance ratio between the resonator and feedline. Electromagnetic and circuit simulations of a ten-channel filterbank near 90GHz at unity oversampling show R=1170\mathcal{R}=1170R=1170 and ηch>78%η_\mathrm{ch}> 78\%ηch​>78%, with no significant trend in efficiency across channels. A ten-channel prototype, designed for R=92±5\mathcal{R}=92\pm5R=92±5 and ηch=(81±3)%η_\mathrm{ch}=(81\pm3)\%ηch​=(81±3)% over 90--106GHz with a 560~nm interlayer based on simulations, was fabricated and optically characterized, yielding R=208±74\mathcal{R}=208\pm74R=208±74 and ηch=(77±6)%η_\mathrm{ch}=(77\pm6)\%ηch​=(77±6)%. Measured ηchη_\mathrm{ch}ηch​ well above the 50% termination limit, together with demonstrated impedance tuning of R\mathcal{R}R, validate the design principles of this filterbank spectrometer and establishes a route to high-efficiency, high-resolution on-chip spectrometer arrays.
We have developed a novel technique for making high quality measurements of the millimeter-wave properties of superconducting thin-film microstrip transmission lines. Our experimental technique currently covers the 75–100 GHz band. The method is based on standing wave resonances in an open ended transmission line. We obtain information on the phase velocity and loss of the microstrip. Our data for Nb/SiO/Nb lines, taken at 4.2 K and 1.6 K, can be explained by a single set of physical parameters. Our preliminary conclusion is that the loss is dominated by the SiO dielectric, with a temperature-independent loss tangent of 5.3±0.5×10−3 for our samples.
Abstract Superconducting on-chip filter banks provide a scalable, space saving solution to create imaging spectrometers at millimetre and submillimetre wavelengths. We present an easy to realise, lithographed superconducting filter design with a high tolerance to fabrication error. Using a capacitively coupled λ/2\lambda /2λ/2 λ / 2 microstrip resonator to define a narrow ( λ/Δλ=300\lambda /\Delta \lambda = 300λ/Δλ=300 λ / Δ λ = 300 ) spectral pass band, the filtered output of a given spectrometer channel directly connects to a lumped-element kinetic inductance detector. We show the tolerance analysis of our design, demonstrating <11%<11\%<11% < 11 % change in filter quality factor to any one realistic fabrication error and a full filter-bank efficiency forecast to be 50% after accounting for fabrication errors and dielectric loss tangent.
Fast and high-fidelity qubit readout requires strong coupling between the readout resonator and the feedline. However, such coupling unavoidably enhances qubit decay through the Purcell effect. We present a four-pole broadband Purcell filter implemented on a 3D flip-chip platform to overcome this trade-off. The filter provides a flat 1 GHz passband centered at 7.68 GHz and achieves more than 45 dB suppression at typical qubit frequencies. We demonstrate the filter's compatibility with multiplexed readout using a test chip that integrates six floating readout resonators strongly coupled within the passband. The chip is fabricated using a 150 nm Niobium (Nb) thin-film process and characterized at 20 mK in a cryogenic measurement setup. We also develop an analytical model that accurately captures the filter response and determines the resonance frequencies and external quality factors of the floating resonators directly from their physical geometry, enabling rapid circuit synthesis and design optimization. The proposed design is compact and fabrication-tolerant, making it a practical solution for large-scale superconducting quantum processors.
Line Intensity Mapping (LIM) is a new observational technique that uses low-resolution observations of line emission to efficiently trace the large-scale structure of the Universe out to high redshift. Common mm/sub-mm emission lines are accessible from ground-based observatories, and the requirements on the detectors for LIM at mm-wavelengths are well matched to the capabilities of large-format arrays of superconducting sensors. We describe the development of an$ R===\lambda / \Delta \lambda = 300$on-chip superconducting filter-bank spectrometer covering the 120–180 GHz band for future mm-LIM experiments, focusing on SPT-SLIM, a pathfinder LIM instrument for the South Pole Telescope. Radiation is coupled from the telescope optical system to the spectrometer chip via an array of feedhorn-coupled orthomode transducers. Superconducting microstrip transmission lines then carry the signal to an array of channelizing half-wavelength resonators, and the output of each spectral channel is sensed by a lumped element kinetic inductance detector (leKID). Key areas of development include incorporating new low-loss dielectrics to improve both the achievable spectral resolution and optical efficiency and development of a robust fabrication process to create a galvanic connection between ultra-pure superconducting thin-films to realize multi-material (hybrid) leKIDs. We provide an overview of the spectrometer design, fabrication process, and prototype devices.
We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.