Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1911.07119

Observation of enhanced coherence in Josephson SQUID cavities using a hybrid fabrication approach

Shun Yanai, Gary Alexander Steele

Published Nov 17, 2019• 2 citations
arXivHTMLPDF

Abstract

We study the coherence of flux-tunable Josephson junction resonators made with two different fabrication processes. In the first process, devices are made using a single step of evaporation in which the resonator and the junctions of the SQUID are made at the same time. In the second process, devices are made with an identical geometry, but in which the resonators are made from a MoRe superconding layer to which an the junctions are added later in a second step. To characterize the coherence of the two types of SQUID cavities, we observe and analyze the quality factor of their resonances as a function of flux and photon number. Despite a detailed cleaning process applied during fabrication, the single-step Al devices show significantly worse quality factor than the hybrid devices, and conclude that a the hybrid technique provides a much more reliable approach for fabricating high-Q flux-tunable resonators.

DOI
10.48550/arxiv.1911.07119

Related papers

Frequency-Tunable Josephson Junction Resonator for Quantum Computing

Kevin D. Osborn, Joshua Strong, Adam J. Sirois +1 more

We have fabricated and measured a high-Q Josephson junction resonator with a tunable resonance frequency. A dc magnetic flux allows the resonance frequency to be changed by over 10%. Weak coupling to the environment allows a quality factor of ~7000 when on average less than one photon is stored in the resonator. At large photon numbers, the nonlinearity of the Josephson junction creates two stable oscillation states. This resonator can be used as a tool for investigating the quality of Josephson junctions in qubits below the single photon limit, and can be used as a microwave qubit readout at high photon numbers.

arXiv:cond-mat/0703103•IEEE Transactions on Applied Superconductivity•Jun 1, 2007•34 citations

Towards Fabrication of Sub-Micrometer Cross-Type Aluminum Josephson Junctions

Stephan Mechold, Katja Peiselt, Matthias Schmelz +5 more

The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.

IEEE Transactions on Applied Superconductivity•Dec 18, 2023•2 citations

A simple method to fabricate Josephson junctions

Imran Mahboob, Satoshi Sasaki, Takaaki Takenaka

A minimal method to fabricate Al/AlO$_x$/Al Josephson junctions (JJs) using photolithography and argon etching, before metallization and oxidation, is demonstrated. JJs with areas ranging from 1 to 6 $μ$m$^2$ can be fabricated and, with the appropriate oxidation conditions, the junction resistance can be varied by $\sim$2 orders of magnitude. Transmission electron microscopy reveals the successful fabrication of JJs with few grain boundaries suggesting reduced energy loss from two-level-systems. Superconducting QUantum Interference Devices (SQUIDs) fabricated from this methodology exhibit reduced resistance variation over multiple chips, compared with electron beam lithography, and the devices can sustain repeated thermal cycles to 10 mK with the excellent flux response remaining unchanged. The quantum applications of this technology are demonstrated by embedding a SQUID resonator into a 3D cavity and parametrically amplifying low photon numbers with gains of $\sim$40 dB. This work establishes the simplest approach to fabricating JJs to date, and it could prove pivotal to the widespread utilization of superconducting circuit-based quantum technologies.

quant-pharXiv:2604.25195•Apr 29, 2026•1 citation

Superconducting Multilayer Technology for Josephson Devices : Technology, Engineering, Physics, Applications

J. M. Meckbach

Within this book fabrication processes for high-quality Josephson junctions based on niobium and aluminum oxide as well as niobium nitride and aluminum nitride on various substrates are discussed. Techniques for achieving a planar chip topography and sub-µm lateral dimensions, aiding the realization of sophisticated Josephson devices such as SQUIDs, flux-flow oscillators and long Josephson junctions with artificial phase discontinuities, are presented in detail.

•Jan 1, 2013•5 citations

Sub-$\mu\hbox{m}$ Josephson Junctions for Superconducting Quantum Devices

J. M. Meckbach, Michael Merker, Simon J. Buehler +7 more

For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.

arXiv:1210.1012•IEEE Transactions on Applied Superconductivity•Dec 4, 2012•11 citations

Hybrid Nb/MoGe Josephson Junctions for the Development of Flux-Flow-Type Josephson Oscillators

Ivan P. Nevirkovets

Josephson junctions (JJs) with layered Nb/MoGe electrodes were fabricated and characterized at 4.2 K. Mo0.75Ge0.25is known to be a superconductor with the transition temperature of up to 7.4 K. It is essentially an amorphous material that has very uniform and smooth surface in thin-film form. This allowed us to fabricate high-quality all-MoGe Josephson junctions with very thin Al overlayer to form AlOxbarrier [Supercond. Sci. Technol., vol. 35, Article no. 035008, 2022]. Here we report JJs with composite Nb/MoGe electrodes aiming at development of flux-flow-type Josephson oscillators operating at low frequencies suitable for qubit control. Using MoGe allows one to preserve a large effective magnetic penetration depth and a high kinetic inductance of the electrodes, which results in (i) a standing wave (Fiske) resonance to occur at lower frequencies, and (ii) in a higher impedance of the oscillator; the latter is important for matching it with other elements of the superconducting circuit. At the same time, using Nb as a part of the composite electrode allows one to maintain the critical parameters (critical current and voltage) of the JJ close to those of the Nb-based JJs. In addition, damping in hybrid Nb/MoGe JJs is lower than that in all-MoGe JJs, which results in a higher current of flux-flow steps, and potentially, in a higher microwave emission power.

IEEE Transactions on Applied Superconductivity•Dec 26, 2024•0 citations
We study the coherence of flux-tunable Josephson junction resonators made with two different fabrication processes. In the first process, devices are made using a single step of evaporation in which the resonator and the junctions of the SQUID are made at the same time. In the second process, devices are made with an identical geometry, but in which the resonators are made from a MoRe superconding layer to which an the junctions are added later in a second step. To characterize the coherence of the two types of SQUID cavities, we observe and analyze the quality factor of their resonances as a function of flux and photon number. Despite a detailed cleaning process applied during fabrication, the single-step Al devices show significantly worse quality factor than the hybrid devices, and conclude that a the hybrid technique provides a much more reliable approach for fabricating high-Q flux-tunable resonators.
We have fabricated and measured a high-Q Josephson junction resonator with a tunable resonance frequency. A dc magnetic flux allows the resonance frequency to be changed by over 10%. Weak coupling to the environment allows a quality factor of ~7000 when on average less than one photon is stored in the resonator. At large photon numbers, the nonlinearity of the Josephson junction creates two stable oscillation states. This resonator can be used as a tool for investigating the quality of Josephson junctions in qubits below the single photon limit, and can be used as a microwave qubit readout at high photon numbers.
The performance of superconducting electronic devices such as superconducting quantum bits (qubits) and superconducting quantum interference devices (SQUIDs) strongly relies on high-quality Josephson junctions (JJ) and their integration into surrounding circuit elements. Therefore, a corresponding fabrication technology should allow for the fabrication of all required elements including the JJs, inductances, capacitances and waveguides. For a long time, shadow evaporation technique was the state of the art for the implementation of sub-μ m sized JJs based on aluminum for qubits of high coherence times. Although, the use of a single lithographic step represents a major advantage of this technique. However, shadowing effects limit sample size, device complexity, and thus scalability of the circuitry. To overcome these limitations and to meet the demands of next generation scalable quantum circuits, in this work we introduce our cross -type JJ aluminum technology, where JJs are defined by the overlap of two narrow perpendicular stripes. We discuss the technological challenges, with a focus on our newly developed dry etching process for patterning of the aluminum thin film. Compared to a lift-off based process, this advanced wafer-scale fabrication technology offers a high integration density and the required design flexibility. We will present first results on cross -type aluminum JJs.
A minimal method to fabricate Al/AlOx_xx​/Al Josephson junctions (JJs) using photolithography and argon etching, before metallization and oxidation, is demonstrated. JJs with areas ranging from 1 to 6 μμμm2^22 can be fabricated and, with the appropriate oxidation conditions, the junction resistance can be varied by $\sim$2 orders of magnitude. Transmission electron microscopy reveals the successful fabrication of JJs with few grain boundaries suggesting reduced energy loss from two-level-systems. Superconducting QUantum Interference Devices (SQUIDs) fabricated from this methodology exhibit reduced resistance variation over multiple chips, compared with electron beam lithography, and the devices can sustain repeated thermal cycles to 10 mK with the excellent flux response remaining unchanged. The quantum applications of this technology are demonstrated by embedding a SQUID resonator into a 3D cavity and parametrically amplifying low photon numbers with gains of $\sim$40 dB. This work establishes the simplest approach to fabricating JJs to date, and it could prove pivotal to the widespread utilization of superconducting circuit-based quantum technologies.
Sub-μm\mu\hbox{m}μm Josephson Junctions for Superconducting Quantum Devices
For high-performance superconducting quantum devices based on Josephson junctions (JJs), decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging, due to nonflat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-and-match process, combining electron-beam lithography and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing procedure. Transport measurements of JJs, having critical-current densities ranging from 50 to 104A/cm2, are presented at 4.2 K. Our JJ process yields excellent quality parameters, Rsg/RNup to ~ 50, Vmfrom 15 to 80 mV and Vgapup to 2.81 mV, and also allows the fabrication of high-quality, sub-μm wide, long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub- μm JJs for quantum devices such as SQUIDs, qubits, and SIS mixers.
Josephson junctions (JJs) with layered Nb/MoGe electrodes were fabricated and characterized at 4.2 K. Mo0.75Ge0.25is known to be a superconductor with the transition temperature of up to 7.4 K. It is essentially an amorphous material that has very uniform and smooth surface in thin-film form. This allowed us to fabricate high-quality all-MoGe Josephson junctions with very thin Al overlayer to form AlOxbarrier [Supercond. Sci. Technol., vol. 35, Article no. 035008, 2022]. Here we report JJs with composite Nb/MoGe electrodes aiming at development of flux-flow-type Josephson oscillators operating at low frequencies suitable for qubit control. Using MoGe allows one to preserve a large effective magnetic penetration depth and a high kinetic inductance of the electrodes, which results in (i) a standing wave (Fiske) resonance to occur at lower frequencies, and (ii) in a higher impedance of the oscillator; the latter is important for matching it with other elements of the superconducting circuit. At the same time, using Nb as a part of the composite electrode allows one to maintain the critical parameters (critical current and voltage) of the JJ close to those of the Nb-based JJs. In addition, damping in hybrid Nb/MoGe JJs is lower than that in all-MoGe JJs, which results in a higher current of flux-flow steps, and potentially, in a higher microwave emission power.