Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1409.7727 · Applied Physics Letters

Development of a broadband reflective T-filter for voltage biasing high-Q superconducting microwave cavities

Yu Hao, Francisco P. M. Rouxinol, M. D. LaHaye

Published Dec 1, 2014• 17 citations
arXivHTMLPDF

Abstract

We present the design of a reflective stop-band filter based on quasi-lumped elements that can be utilized to introduce large dc and low-frequency voltage biases into a low-loss superconducting coplanar waveguide (CPW) cavity. Transmission measurements of the filter are seen to be in good agreement with simulations and demonstrate insertion losses greater than $20\,{\rm dB}$ in the range of ${\rm 3\,to\,10\,GHz}$. Moreover, transmission measurements of the CPW's fundamental mode demonstrate that loaded quality factors exceeding $10^5$ can be achieved with this design for dc voltages as large as ${\rm 20\,V}$ and for the cavity operated in the single-photon regime. This makes the design suitable for use in a number of applications including qubit-coupled mechanical systems and circuit QED.

DOI
10.1063/1.4903777

Related papers

Broadband architecture for galvanically accessible superconducting microwave resonators

Sal J. Bosman, Vibhor Singh, Alessandro Bruno +1 more

In many hybrid quantum systems, a superconducting circuit is required, which combines DC-control with a coplanar waveguide (CPW) microwave resonator. The strategy thus far for applying a DC voltage or current bias to microwave resonators has been to apply the bias through a symmetry point in such a way that it appears as an open circuit for certain frequencies. Here, we introduce a microwave coupler for superconducting CPW cavities in the form of a large shunt capacitance to ground. Such a coupler acts as a broadband mirror for microwaves while providing galvanic connection to the center conductor of the resonator. We demonstrate this approach with a two-port λ/4-transmission resonator with linewidths in the MHz regime (Q∼103) that shows no spurious resonances and apply a voltage bias up to 80 V without affecting the quality factor of the resonator. This resonator coupling architecture, which is simple to engineer, fabricate, and analyse, could have many potential applications in experiments involving superconducting hybrid circuits.

arXiv:1508.05770•Applied Physics Letters•Nov 9, 2015•17 citations

Applying a direct current bias to superconducting microwave resonators by using superconducting quarter wavelength band stop filters

Shaoxiong Li, Jan B. Kycia

We have designed a superconducting quarter wavelength band stop filter which provides a high attenuation at approximately 7 GHz. Such filters were used as dc bias lines applied to whole wavelength and half wavelength superconducting resonators at two different extremes: voltage node and voltage antinode. The results obtained indicate that this filter can apply dc bias to arbitrary length superconducting coplanar waveguide resonators while maintaining high quality factor, Q∼15 000−18 000.

Applied Physics Letters•Jun 17, 2013•18 citations

Design, simulation, fabrication and measurement of a superconducting microwave resonator allowing the application of a DC bias through a symmetry point

P. M. L. Gimbel

Superconducting microwave resonators based on coplanar waveguides (CPWs), which allow for on-chip implementation, have a wide variety of uses, from the coupling of qubits to the detection of photons from interstellar clouds. With the integration of a bias circuitry, the already versatile resonator will become even more so. However, applying a DC voltage or current bias to the resonator without significantly degrading its quality factor Q is no trivial task. One of the first superconducting microwave resonators with the ability to allow for the application of a DC bias, made use of symmetry points. In order to not rely on those symmetry points, our group came up with a different design that used a shunted capacitor instead. However, this design needs a more extensive and in particular more complicated fabrication process. As the groups focus is now completely away from the original design, we go back in this thesis, to honestly evaluate such a resonator by applying a bias to its center. We present a design with the cavity length l to be a full wavelength (l = λ) terminated on both ends to ground, fed in by a capacitively coupled AC-feedline at λ/4 and a DC-bias line at its center (λ/2). After the first fabrication trial we were unable to successfully judge the performance of the microwave resonator as it suffered from bad internal loss, leading to a low internal Q ~ 300 at 4 K. The only thing that this showed us, is that its design is perhaps not as straightforward. On the other hand, interesting results specific to the design were obtained from QUCS simulations (using a combination of lumped and distributed elements). These simulations showed that the quality of the resonator is highly sensitive to the position of its galvanically connected bias line, with respect to the center of the cavity (voltage node). Where Qint drops down to 10 % of its maximum for < 0.1 mm (= l/320) away from the center. Furthermore, we saw that asymmetry in the ports causes the maximum Qint (voltage node) to be off-center by 9 μm, and that adding an extra feedline in symmetry to the existing one puts it back on-center. Demonstrating the voltage node susceptibility to asymmetries of the cavity mode. Despite the unpromising signs the results show, suggestions have been put forward about better isolation of the bias line that have the potential to still make the design attractive. While these isolations still baring the traits of a faster and less complex fabrication.

•Jan 1, 2020•0 citations

Coplanar waveguide resonators for circuit quantum electrodynamics

M. Göppl, A. Fragner, Matthias Baur +7 more

High quality on-chip microwave resonators have recently found prominent new applications in quantum optics and quantum information processing experiments with superconducting electronic circuits, a field now known as circuit quantum electrodynamics (QED). They are also used as single photon detectors and parametric amplifiers. Here we analyze the physical properties of coplanar waveguide resonators and their relation to the materials properties for use in circuit QED. We have designed and fabricated resonators with fundamental frequencies from 2 to 9 GHz and quality factors ranging from a few hundreds to a several hundred thousands controlled by appropriately designed input and output coupling capacitors. The microwave transmission spectra measured at temperatures of 20 mK are shown to be in good agreement with theoretical lumped element and distributed element transmission matrix models. In particular, the experimentally determined resonance frequencies, quality factors, and insertion losses are fully and consistently explained by the two models for all measured devices. The high level of control and flexibility in design renders these resonators ideal for storing and manipulating quantum electromagnetic fields in integrated superconducting electronic circuits.

arXiv:0807.4094•Journal of Applied Physics•Dec 1, 2008•370 citations

Introduction of a dc bias into a high-Q superconducting microwave cavity

Fei Chen, A. J. Sirois, Raymond W. Simmonds +1 more

We report a technique for applying a dc voltage or current bias to the center conductor of a high-quality factor superconducting microwave cavity without significantly disturbing selected cavity modes. This is accomplished by incorporating dc bias lines into the cavity at specific locations. The measured S-matrix parameters of the system are in good agreement with theoretical predictions and simulations. We find that at 4 K the quality factor of the cavity degrades by less than 1% under the application of a dc bias.

arXiv:1101.4218•Applied Physics Letters•Mar 28, 2011•48 citations

Experimental demonstrations of high-Q superconducting coplanar waveguide resonators

HaiJie Li, YiWen Wang, LianFu Wei +6 more

We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.

arXiv:1304.3254•Chinese Science Bulletin•Jul 1, 2013•29 citations
We present the design of a reflective stop-band filter based on quasi-lumped elements that can be utilized to introduce large dc and low-frequency voltage biases into a low-loss superconducting coplanar waveguide (CPW) cavity. Transmission measurements of the filter are seen to be in good agreement with simulations and demonstrate insertion losses greater than 20 dB20\,{\rm dB}20dB in the range of 3 to 10 GHz{\rm 3\,to\,10\,GHz}3to10GHz. Moreover, transmission measurements of the CPW's fundamental mode demonstrate that loaded quality factors exceeding 10510^5105 can be achieved with this design for dc voltages as large as 20 V{\rm 20\,V}20V and for the cavity operated in the single-photon regime. This makes the design suitable for use in a number of applications including qubit-coupled mechanical systems and circuit QED.
In many hybrid quantum systems, a superconducting circuit is required, which combines DC-control with a coplanar waveguide (CPW) microwave resonator. The strategy thus far for applying a DC voltage or current bias to microwave resonators has been to apply the bias through a symmetry point in such a way that it appears as an open circuit for certain frequencies. Here, we introduce a microwave coupler for superconducting CPW cavities in the form of a large shunt capacitance to ground. Such a coupler acts as a broadband mirror for microwaves while providing galvanic connection to the center conductor of the resonator. We demonstrate this approach with a two-port λ/4-transmission resonator with linewidths in the MHz regime (Q∼103) that shows no spurious resonances and apply a voltage bias up to 80 V without affecting the quality factor of the resonator. This resonator coupling architecture, which is simple to engineer, fabricate, and analyse, could have many potential applications in experiments involving superconducting hybrid circuits.
Superconducting microwave resonators based on coplanar waveguides (CPWs), which allow for on-chip implementation, have a wide variety of uses, from the coupling of qubits to the detection of photons from interstellar clouds. With the integration of a bias circuitry, the already versatile resonator will become even more so. However, applying a DC voltage or current bias to the resonator without significantly degrading its quality factor Q is no trivial task. One of the first superconducting microwave resonators with the ability to allow for the application of a DC bias, made use of symmetry points. In order to not rely on those symmetry points, our group came up with a different design that used a shunted capacitor instead. However, this design needs a more extensive and in particular more complicated fabrication process. As the groups focus is now completely away from the original design, we go back in this thesis, to honestly evaluate such a resonator by applying a bias to its center. We present a design with the cavity length l to be a full wavelength (l = λ) terminated on both ends to ground, fed in by a capacitively coupled AC-feedline at λ/4 and a DC-bias line at its center (λ/2). After the first fabrication trial we were unable to successfully judge the performance of the microwave resonator as it suffered from bad internal loss, leading to a low internal Q ~ 300 at 4 K. The only thing that this showed us, is that its design is perhaps not as straightforward. On the other hand, interesting results specific to the design were obtained from QUCS simulations (using a combination of lumped and distributed elements). These simulations showed that the quality of the resonator is highly sensitive to the position of its galvanically connected bias line, with respect to the center of the cavity (voltage node). Where Qint drops down to 10 % of its maximum for < 0.1 mm (= l/320) away from the center. Furthermore, we saw that asymmetry in the ports causes the maximum Qint (voltage node) to be off-center by 9 μm, and that adding an extra feedline in symmetry to the existing one puts it back on-center. Demonstrating the voltage node susceptibility to asymmetries of the cavity mode. Despite the unpromising signs the results show, suggestions have been put forward about better isolation of the bias line that have the potential to still make the design attractive. While these isolations still baring the traits of a faster and less complex fabrication.
High quality on-chip microwave resonators have recently found prominent new applications in quantum optics and quantum information processing experiments with superconducting electronic circuits, a field now known as circuit quantum electrodynamics (QED). They are also used as single photon detectors and parametric amplifiers. Here we analyze the physical properties of coplanar waveguide resonators and their relation to the materials properties for use in circuit QED. We have designed and fabricated resonators with fundamental frequencies from 2 to 9 GHz and quality factors ranging from a few hundreds to a several hundred thousands controlled by appropriately designed input and output coupling capacitors. The microwave transmission spectra measured at temperatures of 20 mK are shown to be in good agreement with theoretical lumped element and distributed element transmission matrix models. In particular, the experimentally determined resonance frequencies, quality factors, and insertion losses are fully and consistently explained by the two models for all measured devices. The high level of control and flexibility in design renders these resonators ideal for storing and manipulating quantum electromagnetic fields in integrated superconducting electronic circuits.
We report a technique for applying a dc voltage or current bias to the center conductor of a high-quality factor superconducting microwave cavity without significantly disturbing selected cavity modes. This is accomplished by incorporating dc bias lines into the cavity at specific locations. The measured S-matrix parameters of the system are in good agreement with theoretical predictions and simulations. We find that at 4 K the quality factor of the cavity degrades by less than 1% under the application of a dc bias.
We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.