This paper reports on experiments with ultracold rubidium atoms confined in microscopic magnetic traps created using a piece of periodically magnetized videotape mounted on an atom chip. The roughness of the confining potential is studied with atomic clouds at temperatures of a few μK and at distances between 30 and 80 μm from the videotape-chip surface. The inhomogeneities in the magnetic field created by the magnetized videotape close to the central region of the chip are characterized in this way. In addition, we demonstrate a novel transport mechanism whereby we convey cold atoms confined in arrays of videotape magnetic micro-traps over distances as large as ∼1 cm parallel to the chip surface. This conveying mechanism enables us to survey the surface of the chip and observe potential-roughness effects across different regions.
This paper reports on experiments with ultracold rubidium atoms confined in microscopic magnetic traps created using a piece of periodically magnetized videotape mounted on an atom chip. The roughness of the confining potential is studied with atomic clouds at temperatures of a few μK and at distances between 30 and 80 μm from the videotape-chip surface. The inhomogeneities in the magnetic field created by the magnetized videotape close to the central region of the chip are characterized in this way. In addition, we demonstrate a novel transport mechanism whereby we convey cold atoms confined in arrays of videotape magnetic micro-traps over distances as large as ∼1 cm parallel to the chip surface. This conveying mechanism enables us to survey the surface of the chip and observe potential-roughness effects across different regions.
Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.
We have produced a Bose-Einstein condensate on a permanent-magnet atom chip based on periodically magnetized videotape. We observe the expansion and dynamics of the condensate in one of the microscopic waveguides close to the surface. The lifetime for atoms to remain trapped near this dielectric material is significantly longer than above a metal surface of the same thickness. These results illustrate the suitability of microscopic permanent-magnet structures for quantum-coherent preparation and manipulation of cold atoms.
In order to take quantum mechanical systems out of the lab and produce practical devices, a method of miniaturizing and integrating apparatus components is needed. In the context of ultracold atomic gas experiments, the ideal method of achieving this miniaturization is the implementation of atom chip technology. By depositing micro-scale current carrying wires onto planar substrates, it is possible to create a magnetic trap capable of confining a cloud of neutral atoms in sufficient proximity to the chip surface for solid state devices to interact with the cloud. This thesis presents our lab’s first steps towards creating an atom chip capable of confining a cloud of rubidium-87. The chip prototypes were developed with the intent to incorporate them into the hybrid system apparatus within our lab. The chips are intended to serve as a platform for facilitating the interaction between the atomic gas ensemble and mesoscopic solid-state devices, allowing for the hybridization of the two systems. In this work I describe the design of the trapping wire configuration and the fabrication of the first two generations of chip prototypes. Additionally, I provide numerical simulations of the produced magnetic field, from which estimates of the trap frequency and depth can be calculated. Finally, I introduce some basic characterization tests of the absolute current limitations and resistive behavior of the chip wires, and the dimensional uniformity of the fabricated wire profiles.
Abstract Atom chips provide flexible technologies for implementing modern concepts in quantum optics, quantum measurement, and quantum information processing. Atom chips are miniature devices that confine, control and manipulate cold atoms using electric, magnetic, and light fields. Due to the shrinkage of scale, arbitrary magnetic traps can be generated from current sources outside the chip’s vacuum compartment, in contrast to a traditional setup. This makes it easy to change trap configurations in an experiment that involves rapid prototyping of quantum states and quantum trajectory designs in free space. In this work, we show relevant parameters needed for transferring a cold atom cloud at the recoil limit from a magneto-optical trap (MOT) to an area close to the atom chip. To create a movable magnetic potential for this transfer, we used the MOT coils and an additional pair of coils in an anti-Helmholtz configuration. The properties of the movable potential were obtained by performing the Computer Simulation Tool (CST EM Studio suite®). Furthermore, an appropriate magnetic trap on a chip is developed, based on the simulation from COMSOL Multiphysics. We used a magnetic field gradient of around 20 G/cm to transport the cold atom with a distance over 20 mm with a temperature gain below 100 micro-Kelvin. The simulation results are based on an atom chip with a size of 2×2 cm2 and a copper wire thickness of 2 mm. The atom chip consists of Z, U and I-shaped wires that generate a quadrupole magnetic field. The resulting field minimum can be made at least 7 mm away from the chip surface.
Atom chips are devices used to magnetically trap and manipulate ultracold atoms and Bose-Einstein condensates near a surface. In particular, permanent magnetic film atom chips can allow very tight confinement and intricate magnetic field designs while circumventing technical current noise. Research described in this thesis is focused on the development of a magnetic film atom chip, the production of Bose-Einstein condensates near the film surface, the characterisation of the associated magnetic potentials using rf spectroscopy of ultracold atoms and the realisation of a precision sensor based on splitting Bose-Einstein condensates in a double-well potential. The atom chip itself combines the edge of a perpendicularly magnetised GdTbFeCo film with a machined silver wire structure. A mirror magneto-optical trap collects up to 5 x 108 87Rb atoms beneath the chip surface. The current-carrying wires are then used to transfer the cloud of atoms to the magnetic film microtrap and radio frequency evaporative cooling is applied to produce Bose-Einstein condensates consisting of 1 x 105 atoms. We have identified small spatial magnetic field variations near the film surface that fragment the ultracold atom cloud. These variations originate from inhomogeneity in the film magnetisation and are characterised using a novel technique based on spatially resolved radio frequency spectroscopy of the atoms to map the magnetic field landscape over a large area. The observations agree with an analytic model for the spatial decay of random magnetic fields from the film surface. Bose-Einstein condensates in our unique potential landscape have been used as a precision sensor for potential gradients. We transfer the atoms to the central region of the chip which produces a double-well potential. A single BEC is formed far from the surface and is then dynamically split in two by moving the trap closer to the surface. After splitting, the population of atoms in each well is extremely sensitive to the asymmetry of the potential and can be used to sense tiny magnetic field gradients or changes in gravity on a small spatial scale.
We describe the production of BECs on a new type of atom chip based on silver foil. Our atom chip is fabricated with thick wires capable of carrying currents of several amperes without overheating. The silver surface is highly reflective to light resonant with optical transitions used for Rb. The pattern on the chip consists of two parallel Z-trap wires, capable of producing two-wire guide, and two additional endcap wires for varying the axial confinement. Condensates are produced in magnetic microtraps formed within 1 mm of surface of the chip. We have observed the fragmentation of cold atom clouds when brought close to the chip surface. This results from a perturbed trapping potential caused by nanometer deviations of the current path through the wires on the chip. We present results of fragmentation of cold clouds at distances below 100 μm from the wires and investigate the origin of the deviating current. The fragmentation has different characteristics to those seen with copper conductors. The dynamics of atoms in these microtraps is also investigated.