In order to take quantum mechanical systems out of the lab and produce practical devices, a method of miniaturizing and integrating apparatus components is needed. In the context of ultracold atomic gas experiments, the ideal method of achieving this miniaturization is the implementation of atom chip technology. By depositing micro-scale current carrying wires onto planar substrates, it is possible to create a magnetic trap capable of confining a cloud of neutral atoms in sufficient proximity to the chip surface for solid state devices to interact with the cloud. This thesis presents our lab’s first steps towards creating an atom chip capable of confining a cloud of rubidium-87. The chip prototypes were developed with the intent to incorporate them into the hybrid system apparatus within our lab. The chips are intended to serve as a platform for facilitating the interaction between the atomic gas ensemble and mesoscopic solid-state devices, allowing for the hybridization of the two systems. In this work I describe the design of the trapping wire configuration and the fabrication of the first two generations of chip prototypes. Additionally, I provide numerical simulations of the produced magnetic field, from which estimates of the trap frequency and depth can be calculated. Finally, I introduce some basic characterization tests of the absolute current limitations and resistive behavior of the chip wires, and the dimensional uniformity of the fabricated wire profiles.
In order to take quantum mechanical systems out of the lab and produce practical devices, a method of miniaturizing and integrating apparatus components is needed. In the context of ultracold atomic gas experiments, the ideal method of achieving this miniaturization is the implementation of atom chip technology. By depositing micro-scale current carrying wires onto planar substrates, it is possible to create a magnetic trap capable of confining a cloud of neutral atoms in sufficient proximity to the chip surface for solid state devices to interact with the cloud. This thesis presents our lab’s first steps towards creating an atom chip capable of confining a cloud of rubidium-87. The chip prototypes were developed with the intent to incorporate them into the hybrid system apparatus within our lab. The chips are intended to serve as a platform for facilitating the interaction between the atomic gas ensemble and mesoscopic solid-state devices, allowing for the hybridization of the two systems. In this work I describe the design of the trapping wire configuration and the fabrication of the first two generations of chip prototypes. Additionally, I provide numerical simulations of the produced magnetic field, from which estimates of the trap frequency and depth can be calculated. Finally, I introduce some basic characterization tests of the absolute current limitations and resistive behavior of the chip wires, and the dimensional uniformity of the fabricated wire profiles.
Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.
Atom chips provide a convenient platform to study ultracold quantum gases and their interactions with electromagnetic fields, surfaces, micro-magnetic structures, superconducting circuits and nanomechanical systems. The research work presented in this thesis is classified in two major categories. The first part is focused on the development and construction of a permanent magnetic lattice on an atom chip and the study of trapped atoms in the permanent magnetic lattice potential. In the second part, a new experiment is proposed to create a macroscopic entanglement between the flux state of a superconducting loop and a Bose-Einstein condensate (BEC) on a superconducting atom chip. The permanent magnetic lattice potential is produced by applying a uniform bias magnetic field to a grooved silicon structure coated with a permanent magnetic film. The magnetic film consists of a multilayer structure of GdTbFeCo with perpendicular intrinsic magnetization. The permanent magnetic structure is mounted beneath a current carrying wire structure glued to a ceramic insulator. The current carrying wires assist in the preparation of the ultracold atoms and for loading into the magnetic lattice. In addition, the current carrying wires are used to produce a BEC in a Z- wire magnetic trap. The magnetic lattice potential is produced by a one-dimensional array of highly anisotropic and extremely tight magnetic microtraps of period 10 ¹m. A detailed study of the reflection dynamics of atoms in the magnetic lattice potential is presented along with numerical simulations. Finally, the trapping of atoms in the permanent magnetic lattice at a distance less than 5 ¹m from the surface of the atom chip is described. The properties of the trapped atoms including lifetime, temperature and trap frequency are discussed. A maximum radial trap frequency of about 90 kHz is measured in the magnetic lattice potential with no confinement applied along the axial direction. A new experiment which combines the quantum coherent dynamics in superconducting circuits and BEC manipulation on a superconducting atom chip is proposed and investigated. It is shown how a macroscopic entanglement can be produced between the flux state of a superconducting loop and the state of a BEC trapped in a magnetic trap. In addition, the detection of the macroscopic entanglement based on a quantum eraser and an entangled BEC interference is discussed. Thus, this proposal provides a platform to realise interferometry with an entangled BEC and to explore the quantum-classical interface.
Atom chips are an excellent tool for studying ultracold degenerate quantum gases, due to the high degree of controllability afforded by the precise potentials generated from the current-carrying microfabricated wires on the chip surface. The geometries of the trapping potentials are inherently capable of realising extreme aspect ratios, and therefore creating model systems with effectively reduced dimensionality, particularly the theoretically-tractable one-dimensional Bose gas. In addition, the temporal tunability makes it possible to impart non-adiabatic changes on the trapping potentials, allowing experimental investigation of samples which have been brought out of equilibrium - a situation which is not fully theoretically understood. This thesis describes the implementation, development and characterisation of an experimental system for producing the first Bose-Einstein condensates of atomic rubidium 87 gas trapped on the surface of an atom chip in Nottingham. Such an apparatus is very complex and requires careful characterisation in order to run in a stable and reliable way. Details of the experimental setup are thoroughly outlined, including the vacuum system, lasers, electronics, computer control and timing, and the optical imaging system. A newly installed compact two-dimensional magneto-optical trap provides an loading rate of 5e7 atoms per second for loading a three-dimensional mirror-magneto-optical trap with 1.5e8 atoms, at a temperature of 300uK within 10s. The cloud is then sub-Doppler cooled to 50uK, and spin-polarised with 96% purity into the |F=2,mF=+2> ground state within 5ms, in preparation for loading a purely magnetic trap. A millimeter sized copper Z-shaped conductor located beneath the atom chip surface creates a Ioffe-Pritchard magnetic trap, into which the laser cooled cloud is loaded with 70% efficiency, and can be held with a vacuum-limited lifetime of 40s. Evaporative cooling then pre-cools the sample to below 20uK within 10s, to allow the subsequent loading into potentials created by the atom chip with 100% efficiency. A final evaporation stage then cools the cloud below the phase transition temperature of 800nK, resulting finally in pure BECs with 105 atoms confined using the atom chip. Key measurements of various properties of the trapped condensates are presented, which are important in order to characterise the system fully, and to compare with theoretical expectations. In particular, included are the variation of condensate fraction with temperature, the BEC expansion dynamics, and the condensate lifetime in the trap, for example. Finally, it is demonstrated how BECs can be produced on the atom chip without the use of external macroscopic coils, achieved by using novel, integrated sheet structures located beneath the chip surface - unique to this experimental system - to create the necessary bias fields.
Atom chips are robust and extremely powerful toolboxes for quantum optical experiments, since they make it possible to create exceedingly precise magnetic traps for neutral atoms with minimal field modulations. Accurate manipulation of trapped atoms is feasible with magnetic and electric fields created on the atom chip. Therefore atom chips with high quality surfaces and extremely well defined wires were build (roughness < 20nm). Furthermore new generations of atom chips were developed, like the multi-layer atom chip with contact-free wire crossings, the sub-micron structured atom chip and the semiconducting atom chip. Extensive characterisation measurements of atom chip wires demonstrated that the wires stand current densities of up to 10^7A/cm^2 for seconds and voltage differences of more than 500V over 10µm. From the different materials tested doped silicon with a thin silicon dioxide layer is the best qualified substrate for atom chip fabrication. The atom chips fabricated during this thesis have been used in many successful experiments, yielding numerous results. Moreover this thesis established the basics for many further experiments in atom physics and quantum optics and delivers complete instructions for the fabrication of all developed atom chips as well as an introduction to the experiments.
This thesis describes the design and realization of a novel experimental setup for the investigation of ultracold Bose-Fermi mixtures. The new setup combines a mixture experiment of 40K and 87Rb with one-dimensional trapping geometries that are accessible in the miniaturized wire traps of an atom chip. By additionally coupling the internal states of magnetically trapped atoms with radio-frequency (rf) fields, versatile state-selective and species-selective potentials can be created. One special case is the deformation of the static one-dimensional trap to a novel two-dimensional geometry in which the atoms are confined to the walls of a straight tube. An extensive numerical and experimental analysis of this trapping geometry with the aim of minimizing the variations in the trapping potential was performed. This leads to a new improved spatial arrangement for the wires that create the rf fields. The optimized wire layout was implemented in the new experimental setup and will allow the first realization of such a two-dimensional trap configuration with periodic boundary conditions. Results of experiments performed with a simplified arrangement of the rf wires allowed the observation of the two-dimensional regime with thermal atoms.
Abstract Atom chips provide flexible technologies for implementing modern concepts in quantum optics, quantum measurement, and quantum information processing. Atom chips are miniature devices that confine, control and manipulate cold atoms using electric, magnetic, and light fields. Due to the shrinkage of scale, arbitrary magnetic traps can be generated from current sources outside the chip’s vacuum compartment, in contrast to a traditional setup. This makes it easy to change trap configurations in an experiment that involves rapid prototyping of quantum states and quantum trajectory designs in free space. In this work, we show relevant parameters needed for transferring a cold atom cloud at the recoil limit from a magneto-optical trap (MOT) to an area close to the atom chip. To create a movable magnetic potential for this transfer, we used the MOT coils and an additional pair of coils in an anti-Helmholtz configuration. The properties of the movable potential were obtained by performing the Computer Simulation Tool (CST EM Studio suite®). Furthermore, an appropriate magnetic trap on a chip is developed, based on the simulation from COMSOL Multiphysics. We used a magnetic field gradient of around 20 G/cm to transport the cold atom with a distance over 20 mm with a temperature gain below 100 micro-Kelvin. The simulation results are based on an atom chip with a size of 2×2 cm2 and a copper wire thickness of 2 mm. The atom chip consists of Z, U and I-shaped wires that generate a quadrupole magnetic field. The resulting field minimum can be made at least 7 mm away from the chip surface.