Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:quant-ph/0303001 · Physical review. B, Condensed matter

Decoherence in a Josephson-junction qubit

A. J. Berkley, H. Xu, M. A. Gubrud, Roberto Ramos, J. R. Anderson, Christopher J. Lobb, F. C. Wellstood

Published Aug 18, 2003• 50 citations
arXivHTMLPDF

Abstract

The zero-voltage state of a Josephson junction biased with constant current consists of a set of metastable quantum energy levels. We probe the spacings of these levels by using microwaves to induce transitions and thereby enhance the escape rate to the voltage state. The widths of the resonances give a measurement of the spectroscopic coherence time of the two metastable states involved in the transitions. We observe a decoherence time shorter than that expected from dissipation alone in resonantly isolated $20\ifmmode\times\else\texttimes\fi{}5\ensuremath{\mu}{\mathrm{m}}^{2}$ area $\mathrm{Al}/\mathrm{AlO}x/\mathrm{Al}$ junctions at 60 mK. The data are well fit by a model that includes the dephasing effects of both low-frequency current noise and the escape rate to the voltage state. We discuss implications for quantum computation using current-biased Josephson-junction qubits, including limits on the minimum number of levels needed in the well.

DOI
10.1103/physrevb.68.060502

Related papers

A Josephson junction qubit

A. J. Berkley

I studied the Josephson junction system in the context of its usability for quan-tum computation. The zero-voltage state of a Josephson junction biased with constant current has a set of metastable quantum energy levels. In principle, it should be possible to use the two lowest states as a qubit for a quantum computer, provided both the dissipation time and coherence time of this qubit can be made long enough. I describe two methods for isolating a Josephson junction to increase its dissipation time. The rst is a resistive isolation scheme, for which I fabricated and measured a prototype system. I discuss the results of these measurements and show that the constraints of heating in conjunction with high-frequency design require-ments make it unlikely that this isolation method will lead to the coherence times required for quantum computation. I then discuss a resonant isolation method that I used to successfully increase the dissipation time of a Josephson junction qubit. I performed spectroscopic mea-surements at low temperatures to nd the coherence time of resonantly isolated 100 m2 Al/AlOx/Al and Nb/AlOx/Nb junctions with critical currents of roughly 10 A. The results of these measurements reveal two mechanisms beyond spontaneous emission for decoherence: low-frequency current noise and tunneling to the voltage state. To explain these results on decoherence, I present a model based on the Bloch equations. Going beyond a single qubit, I designed a capacitively coupled two-qubit system. Using spectroscopy, I showed that the energy level spacings between the ground state and the excited entangled states of the system agree with those calculated from the Schrodinger equation.

•Jan 1, 2003•2 citations

Quantum Computing with Josephson Junction Circuits

Huizhong Xu

This work concerns the study of Josephson junction circuits in the context of their usability for quantum computing. The zero-voltage state of a current-biased Josephson junction has a set of metastable quantum energy levels. If a junction is well isolated from its environment, it will be possible to use the two lowest states as a qubit in a quantum computer. I first examine the meaning of isolation theoretically. Using a master equation, I analyzed the effect of dissipation on escape rates and suggested a simple method, population depletion technique, to measure the relaxation time. Using a stochastic Bloch equation to analyze microwave resonance shapes, I found a relation between current noise induced decoherence and the noise spectrum. I then analyze and test a few qubit isolation schemes, including resistive isolation, inductor-capacitor (LC) isolation, and inductor-junction (LJ) isolation. I found the resistive isolation scheme has a severe heating problem. Macroscopic quantum tunneling and energy level quantization were observed in the LC isolated junction qubits at 25 mK. Relaxation times of 4-12 ns and spectroscopic coherence times of 1-3 ns were obtained for these LC isolated qubits. I measured a relaxation time of 50 ns and a spectroscopic coherence time of 5-8 ns for the LJ isolated junction qubit. Both times are much longer than those of the LC isolated qubits. Rabi oscillations were also observed on this sample with a decay time of around 10 ns. Using microwave spectroscopy techniques, I probed quantum phenomena in a coupled macroscopic three-qubit system that is comprised of two Nb/AlOx/Nb Josephson junctions and an LC resonator. The measured spectrum at 25 mK in the frequency range 4-15 GHz agrees well with quantum mechanical calculations, consistent with the existence of entangled states between the three degrees of freedom. These entangled states and a first-order strong coupling between two junction qubits open the possibility of using a resonator as a data bus for information storage and manipulation in a multi-qubit system. The measurements also demonstrate spectroscopy is a powerful tool and can be used to study a composite system with many qubits.

•Aug 27, 2004•4 citations

Characterization of an LC-isolated Josephson junction qubit

A. J. Berkley, Haitan Xu, M. A. Gubrud +4 more

The energy states of a well-isolated hysteretic Josephson junction in the "phase" regime can be used as a qubit. The state of the junction can be determined by measuring when the junction switches from the zero-voltage (qubit) state to the running voltage state, since different levels have different switching rates. The experimental challenge is to provide sufficient electrical isolation of the junction from wires that must be attached to provide bias current and to measure switching events. This isolation must be effective at frequencies around the energy level spacing, in our case from 3-8 GHz. We report on the design and measurement of isolated moderate-to-high-Q junctions using a resonant isolation scheme of a series inductance and capacitive shunt. Microwave activation measurements of the Al-AlO/sub x/-Al junctions at 70 mK were used to gauge the isolation effectiveness and to show the effect of current noise from the isolation resonance on the junction coherence.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

Characterization of Josephson devices for use in quantum computation

Sudeep Dutta

This thesis examines Josephson tunnel junctions as candidate qubits for quantum computation. A large area current-biased junction, known as a phase qubit, uses the two lowest energy levels in a tilted washboard potential as the qubit states |0> and |1>. I performed experiments with 10 x 10 um^2 Nb/AlOx/Nb qubit junctions, with critical currents of roughly 30 uA. The state of a device was initialized by cooling below 50 mK in a dilution refrigerator. In order for quantum mechanical superpositions to be long-lived, it is necessary to isolate the junction from noisy bias leads that originate at room temperature. I studied two types of isolation: an LC filter, and a broadband scheme that used an auxiliary junction, resulting in a dc SQUID. One of the main goals of this work was to determine how well a simple Hamiltonian, derived assuming just a few lumped elements, describes the observed behavior of a macroscopic Josephson device, including coherent dynamics such as Rabi oscillations. I did this by comparing results to the expected behavior of ideal two-level systems and with more detailed master equation and density matrix simulations. I performed state manipulation by applying dc bias currents and resonant microwave currents, and through temperature control. The tunneling escape rate of the junction from the states |0> and |1> (zero voltage) to the running state (finite voltage) depends on the occupation probability of the energy levels and served as state readout. Experiments to measure the relaxation time T1 between |1> and |0> were performed by examining the dependence of the escape rate with temperature, yielding a maximum T1 = 15 ns. Measuring the decay to the ground state after applying a microwave pulse revealed at least two time constants, one of about 10 ns and another as long as 50 ns. The spectroscopic coherence time T2* was estimated to be roughly 5 ns by measuring resonance widths and the decay envelope of coherent Rabi oscillations was found to have a time constant T' = 10 ns over a wide range of conditions.

•Nov 28, 2006•3 citations

Determination of relaxation time of a Josephson junction qubit

S. K. Dutta, Haitan Xu, A. J. Berkley +5 more

When a Josephson junction in the zero-voltage state is current-biased below its critical current, the rate that it escapes to the finite-voltage state depends on the quantum state of the junction. By employing a slow current sweep, it is possible to observe experimentally the emptying of the thermally populated first excited level as a well-defined feature in the escape rate. This feature provides a simple method of determining the junction's energy relaxation time ${T}_{1}$, a key parameter for evaluating its utility for quantum computation. We discuss the temperature regime where this effect is readily observable and describe how the emptying depends directly on the relaxation time. Our model of the junction dynamics agrees well with the measured escape rate of a $10\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}\ifmmode\times\else\texttimes\fi{}10\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}$ $\mathrm{Nb}\text{\ensuremath{-}}\mathrm{AlOx}\text{\ensuremath{-}}\mathrm{Nb}$ device in the 25 to $300\phantom{\rule{0.3em}{0ex}}\mathrm{mK}$ temperature range, yielding ${T}_{1}\ensuremath{\approx}4\phantom{\rule{0.3em}{0ex}}\mathrm{ns}$.

Physical Review B•Oct 7, 2004•12 citations

Measurements of 1∕f noise in Josephson junctions at zero voltage: Implications for decoherence in superconducting quantum bits

Michael Mück, Matthias Korn, Chas Mugford +2 more

Critical current fluctuations with a 1∕f spectral density (f is frequency) are potentially a limiting source of intrinsic decoherence in superconducting quantum bits (qubits) based on Josephson tunnel junctions. Prior measurements of this noise were made at nonzero voltages whereas qubits are operated in the zero voltage state. We report measurements of 1∕f noise in a dc superconducting quantum interference device first, coupled to a resonant tank circuit and operated in a dispersive mode at zero voltage, and, second, operated conventionally with a current bias in the voltage regime. Both measurements yield essentially the same magnitude of critical current 1∕f noise.

arXiv:cond-mat/0501153•Applied Physics Letters•Dec 27, 2004•19 citations
The zero-voltage state of a Josephson junction biased with constant current consists of a set of metastable quantum energy levels. We probe the spacings of these levels by using microwaves to induce transitions and thereby enhance the escape rate to the voltage state. The widths of the resonances give a measurement of the spectroscopic coherence time of the two metastable states involved in the transitions. We observe a decoherence time shorter than that expected from dissipation alone in resonantly isolated 20\ifmmode×\else\texttimes\fi5\ensuremathμm220\ifmmode\times\else\texttimes\fi{}5\ensuremath{\mu}{\mathrm{m}}^{2}20\ifmmode×\else\texttimes\fi5\ensuremathμm2 area Al/AlOx/Al\mathrm{Al}/\mathrm{AlO}x/\mathrm{Al}Al/AlOx/Al junctions at 60 mK. The data are well fit by a model that includes the dephasing effects of both low-frequency current noise and the escape rate to the voltage state. We discuss implications for quantum computation using current-biased Josephson-junction qubits, including limits on the minimum number of levels needed in the well.
I studied the Josephson junction system in the context of its usability for quan-tum computation. The zero-voltage state of a Josephson junction biased with constant current has a set of metastable quantum energy levels. In principle, it should be possible to use the two lowest states as a qubit for a quantum computer, provided both the dissipation time and coherence time of this qubit can be made long enough. I describe two methods for isolating a Josephson junction to increase its dissipation time. The rst is a resistive isolation scheme, for which I fabricated and measured a prototype system. I discuss the results of these measurements and show that the constraints of heating in conjunction with high-frequency design require-ments make it unlikely that this isolation method will lead to the coherence times required for quantum computation. I then discuss a resonant isolation method that I used to successfully increase the dissipation time of a Josephson junction qubit. I performed spectroscopic mea-surements at low temperatures to nd the coherence time of resonantly isolated 100 m2 Al/AlOx/Al and Nb/AlOx/Nb junctions with critical currents of roughly 10 A. The results of these measurements reveal two mechanisms beyond spontaneous emission for decoherence: low-frequency current noise and tunneling to the voltage state. To explain these results on decoherence, I present a model based on the Bloch equations. Going beyond a single qubit, I designed a capacitively coupled two-qubit system. Using spectroscopy, I showed that the energy level spacings between the ground state and the excited entangled states of the system agree with those calculated from the Schrodinger equation.
This work concerns the study of Josephson junction circuits in the context of their usability for quantum computing. The zero-voltage state of a current-biased Josephson junction has a set of metastable quantum energy levels. If a junction is well isolated from its environment, it will be possible to use the two lowest states as a qubit in a quantum computer. I first examine the meaning of isolation theoretically. Using a master equation, I analyzed the effect of dissipation on escape rates and suggested a simple method, population depletion technique, to measure the relaxation time. Using a stochastic Bloch equation to analyze microwave resonance shapes, I found a relation between current noise induced decoherence and the noise spectrum. I then analyze and test a few qubit isolation schemes, including resistive isolation, inductor-capacitor (LC) isolation, and inductor-junction (LJ) isolation. I found the resistive isolation scheme has a severe heating problem. Macroscopic quantum tunneling and energy level quantization were observed in the LC isolated junction qubits at 25 mK. Relaxation times of 4-12 ns and spectroscopic coherence times of 1-3 ns were obtained for these LC isolated qubits. I measured a relaxation time of 50 ns and a spectroscopic coherence time of 5-8 ns for the LJ isolated junction qubit. Both times are much longer than those of the LC isolated qubits. Rabi oscillations were also observed on this sample with a decay time of around 10 ns. Using microwave spectroscopy techniques, I probed quantum phenomena in a coupled macroscopic three-qubit system that is comprised of two Nb/AlOx/Nb Josephson junctions and an LC resonator. The measured spectrum at 25 mK in the frequency range 4-15 GHz agrees well with quantum mechanical calculations, consistent with the existence of entangled states between the three degrees of freedom. These entangled states and a first-order strong coupling between two junction qubits open the possibility of using a resonator as a data bus for information storage and manipulation in a multi-qubit system. The measurements also demonstrate spectroscopy is a powerful tool and can be used to study a composite system with many qubits.
The energy states of a well-isolated hysteretic Josephson junction in the "phase" regime can be used as a qubit. The state of the junction can be determined by measuring when the junction switches from the zero-voltage (qubit) state to the running voltage state, since different levels have different switching rates. The experimental challenge is to provide sufficient electrical isolation of the junction from wires that must be attached to provide bias current and to measure switching events. This isolation must be effective at frequencies around the energy level spacing, in our case from 3-8 GHz. We report on the design and measurement of isolated moderate-to-high-Q junctions using a resonant isolation scheme of a series inductance and capacitive shunt. Microwave activation measurements of the Al-AlO/sub x/-Al junctions at 70 mK were used to gauge the isolation effectiveness and to show the effect of current noise from the isolation resonance on the junction coherence.
This thesis examines Josephson tunnel junctions as candidate qubits for quantum computation. A large area current-biased junction, known as a phase qubit, uses the two lowest energy levels in a tilted washboard potential as the qubit states |0> and |1>. I performed experiments with 10 x 10 um^2 Nb/AlOx/Nb qubit junctions, with critical currents of roughly 30 uA. The state of a device was initialized by cooling below 50 mK in a dilution refrigerator. In order for quantum mechanical superpositions to be long-lived, it is necessary to isolate the junction from noisy bias leads that originate at room temperature. I studied two types of isolation: an LC filter, and a broadband scheme that used an auxiliary junction, resulting in a dc SQUID. One of the main goals of this work was to determine how well a simple Hamiltonian, derived assuming just a few lumped elements, describes the observed behavior of a macroscopic Josephson device, including coherent dynamics such as Rabi oscillations. I did this by comparing results to the expected behavior of ideal two-level systems and with more detailed master equation and density matrix simulations. I performed state manipulation by applying dc bias currents and resonant microwave currents, and through temperature control. The tunneling escape rate of the junction from the states |0> and |1> (zero voltage) to the running state (finite voltage) depends on the occupation probability of the energy levels and served as state readout. Experiments to measure the relaxation time T1 between |1> and |0> were performed by examining the dependence of the escape rate with temperature, yielding a maximum T1 = 15 ns. Measuring the decay to the ground state after applying a microwave pulse revealed at least two time constants, one of about 10 ns and another as long as 50 ns. The spectroscopic coherence time T2* was estimated to be roughly 5 ns by measuring resonance widths and the decay envelope of coherent Rabi oscillations was found to have a time constant T' = 10 ns over a wide range of conditions.
When a Josephson junction in the zero-voltage state is current-biased below its critical current, the rate that it escapes to the finite-voltage state depends on the quantum state of the junction. By employing a slow current sweep, it is possible to observe experimentally the emptying of the thermally populated first excited level as a well-defined feature in the escape rate. This feature provides a simple method of determining the junction's energy relaxation time T1{T}_{1}T1​, a key parameter for evaluating its utility for quantum computation. We discuss the temperature regime where this effect is readily observable and describe how the emptying depends directly on the relaxation time. Our model of the junction dynamics agrees well with the measured escape rate of a $10\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}\ifmmode\times\else\texttimes\fi{}10\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}$ $\mathrm{Nb}\text{\ensuremath{-}}\mathrm{AlOx}\text{\ensuremath{-}}\mathrm{Nb}$ device in the 25 to 300mK300\phantom{\rule{0.3em}{0ex}}\mathrm{mK}300mK temperature range, yielding ${T}_{1}\ensuremath{\approx}4\phantom{\rule{0.3em}{0ex}}\mathrm{ns}$.
Critical current fluctuations with a 1∕f spectral density (f is frequency) are potentially a limiting source of intrinsic decoherence in superconducting quantum bits (qubits) based on Josephson tunnel junctions. Prior measurements of this noise were made at nonzero voltages whereas qubits are operated in the zero voltage state. We report measurements of 1∕f noise in a dc superconducting quantum interference device first, coupled to a resonant tank circuit and operated in a dispersive mode at zero voltage, and, second, operated conventionally with a current bias in the voltage regime. Both measurements yield essentially the same magnitude of critical current 1∕f noise.