Linking a superconducting circuit to an optical fibre requires converting a microwave photon into an optical photon. In an electro-optic or optomechanical converter the efficiency is set by two cooperativities, one on each side of the device, and by how well they are matched. This study computes the quantities that follow from stated assumptions for a bidirectional converter with internal efficiency formula stated in the text, external coupling 0.9 on each side, and a thermal occupation of 0.1 microwave photons, using the relations set out in the Methods. The headline results are eta at C 10 10 = 0.907, eta external at C 10 10 = 0.7347, eta at C 10 100 = 0.3246, eta at C 1 1 = 0.4444, eta at C 100 100 = 0.9901. The central question is stated as follows: What conversion efficiency and added noise follow for cooperativity pairs from below unity to one hundred, and how much efficiency is lost when the two cooperativities differ by a factor of ten? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Reported conversion efficiencies span many orders of magnitude, from very small values in early devices to tens of percent in the most advanced, with added noise often the stricter criterion. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Linking a superconducting circuit to an optical fibre requires converting a microwave photon into an optical photon. In an electro-optic or optomechanical converter the efficiency is set by two cooperativities, one on each side of the device, and by how well they are matched. This study computes the quantities that follow from stated assumptions for a bidirectional converter with internal efficiency formula stated in the text, external coupling 0.9 on each side, and a thermal occupation of 0.1 microwave photons, using the relations set out in the Methods. The headline results are eta at C 10 10 = 0.907, eta external at C 10 10 = 0.7347, eta at C 10 100 = 0.3246, eta at C 1 1 = 0.4444, eta at C 100 100 = 0.9901. The central question is stated as follows: What conversion efficiency and added noise follow for cooperativity pairs from below unity to one hundred, and how much efficiency is lost when the two cooperativities differ by a factor of ten? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Reported conversion efficiencies span many orders of magnitude, from very small values in early devices to tens of percent in the most advanced, with added noise often the stricter criterion. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
In a multi-photon circuit every photon must survive source, coupling, propagation and detection. Because survival probabilities multiply, a per-photon efficiency that looks acceptable for one photon can leave almost no complete events when twenty photons are required together. This study computes the quantities that follow from stated assumptions for an interference circuit fed by independent single photons, with a single overall per-photon efficiency combining source, circuit and detector, using the relations set out in the Methods. The headline results are P20 at eta 0.85 = 0.03876, P20 at eta 0.95 = 0.3585, P10 at eta 0.7 = 0.02825, eta needed for 1pct at n20 = 0.7943, eta needed for 10pct at n20 = 0.8913. Further computed values are P50 at eta 0.95 = 0.07694. The central question is stated as follows: For per-photon efficiencies from 0.5 to 0.95, what fraction of ten-, twenty- and fifty-photon events survive complete, and what per-photon efficiency is needed to keep one percent of twenty-photon events? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Multi-photon experiments have progressed from a handful of photons to several tens, with overall efficiencies, rather than source brightness alone, repeatedly identified as the limiting factor. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
The development of scalable quantum networks requires coherent interfaces capable of converting microwave photons used in superconducting quantum processors into optical photons suitable for long-distance fiber transmission. This review surveys recent progress in microwave-to-optical quantum transduction across optomechanical, electro-optic, and magneto-optic platforms, with emphasis on conversion efficiency, bandwidth, added noise, and operating temperature. In addition to standard metrics, we propose the internal efficiency eta_in and the magnon decay rate kappa_m/2pi as normalized parameters that enable fairer comparison across heterogeneous implementations. Optomechanical systems achieve internal phonon-to-photon efficiencies of 93% with sub-quantum added noise of 0.25 quanta at millikelvin temperatures. Electro-optic devices based on LiNbO3 and AlN have advanced from room-temperature efficiencies below 1% to millikelvin systems with internal efficiencies approaching 99.5%, added noise as low as 0.16 quanta at 60 mK, and bandwidths extending to several tens of megahertz. Magneto-optic (optomagnonic) platforms exhibit the lowest efficiencies (typically 10−10 to 10−8), but offer intrinsic non-reciprocity and broadband magnonic operation, with emerging approaches based on topological heterostructures and magnon squeezing predicting enhancements up to 10−4. Optomechanical systems appear promising for high-fidelity quantum state transfer, electro-optic transducers for high-bandwidth coherent links, and magneto-optic devices for non-reciprocal network components. We discuss the fundamental trade-off between efficiency and added noise across all three platforms, and argue that heterogeneous microwave-optical transduction is emerging as a key enabling technology for distributed quantum computing and large-scale quantum networks.
Entanglement swapping joins two independently created links into one longer link. With linear optics the joining measurement succeeds at most half the time even with perfect equipment, and channel loss and detector efficiency reduce the rate far below that limit. This study computes the quantities that follow from stated assumptions for two pair sources, a linear-optical Bell measurement with success factor one half, channel transmission per arm from 0.1 to 0.9, detector efficiency 0.9, using the relations set out in the Methods. The headline results are rate at eta ch 0.5 Hz = 101.3, rate at eta ch 0.9 Hz = 328.1, rate at eta ch 0.1 Hz = 4.05, success at eta ch 0.5 = 1.013e-05, rate ratio 0.9 over 0.5 = 3.24. The central question is stated as follows: For stated channel transmissions and detector efficiencies, what swapping success probability and rate follow for two sources each producing a pair with probability 0.01 per attempt at 10 MHz, and which single improvement raises the rate most? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Swapping demonstrations report success probabilities far below the linear-optical limit once loss is included, and rates from below one per hour in long-distance work to kilohertz scales in local experiments. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
A photon reflected from a cavity that contains a coupled emitter acquires a phase that depends on the emitter state. That conditional phase is the working principle of a photon router and of several photon-photon gate proposals, and its usefulness is set by the cooperativity. This study computes the quantities that follow from stated assumptions for a one-sided cavity coupled to a two-level emitter, probed on resonance by a narrowband single photon, using the relations set out in the Methods. The headline results are fidelity at C 5 = 0.9091, fidelity at C 20 = 0.9756, fidelity at C 100 = 0.995, reflection at C 5 = 0.8182, loss at C 20 = 0.09518. The central question is stated as follows: For cooperativities from one half to one hundred, what reflection amplitudes, conditional phase error and routing fidelity follow in the standard input-output model? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Conditional phase shifts approaching pi and gate fidelities limited mainly by cooperativity are the standard theoretical expectations for this geometry, with experiments reporting smaller shifts where cooperativity is modest. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Solid-state microwave systems offer strong interactions for fast quantum logic and sensing but photons at telecom wavelength are the ideal choice for high-density low-loss quantum interconnects. A general-purpose interface that can make use of single photon effects requires < 1 input noise quanta, which has remained elusive due to either low efficiency or pump induced heating. Here we demonstrate coherent electro-optic modulation on nanosecond-timescales with only [Formula: see text] microwave input noise photons with a total bidirectional transduction efficiency of 8.7% (or up to 15% with [Formula: see text]), as required for near-term heralded quantum network protocols. The use of short and high-power optical pump pulses also enables near-unity cooperativity of the electro-optic interaction leading to an internal pure conversion efficiency of up to 99.5%. Together with the low mode occupancy this provides evidence for electro-optic laser cooling and vacuum amplification as predicted a decade ago.
Converting signals from the microwave to the optical domain has attracted great attention due to its potential applications in the field of quantum networks. Achieving efficient transduction is a significant yet challenging task, where a high efficiency at single photon level and low added noise are required. Electro-opto-mechanics have been proven to be efficient to convert microwave and optical photons bidirectionally. In this work, we propose and demonstrate an enhanced microwave-optical conversion in an electro-opto-mechanical system by introducing a mechanical ancilla attached the microwave resonator. Based on the ancillary electromechanical coupling, the damping rate of the microwave resonator is controlled and further leads to significant enhancement in conversion, such as the increase of conversion efficiency, broadening of conversion bandwidth and reduction of added noise. It provides a feasible approach to realize a broadband microwave-optical conversion with high efficiency. Moreover, the reduced added noise may break the limitation of quantum transduction due to the ancillary electromechanical coupling. Our scheme is also applicable and feasible for opto-mechanics and other systems to achieve practical quantum interface.