Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Josephson Latching Driver Designed Using 10-kA/cm Nb Process as Interface for Josephson-CMOS Hybrid Memory

Yuki Hironaka, Nobuyuki Yoshikawa

Published Nov 28, 2024• 2 citations
Publisher

Abstract

In this study, we designed, fabricated, and experimentally tested a Josephson latching driver (JLD), a superconductor-to-semiconductor interface circuit for use in Josephson-CMOS hybrid memory, utilizing a 10-kA/cm2Nb process. The JLD is composed of a voltage driver known as a Suzuki stack and a Josephson four-junction logic (4JL) gate that serves as a preamplifier. The basic structure is based on our previous design using the 2.5-kA/cm2Nb process. In this study, we optimized the critical current and the load resistance of the 4JL gate, taking into account the parameters of the Josephson junctions in the 10-kA/cm2process. In experiments with the fabricated test circuit, we confirmed the correct operation of the JLD (bit error rate−11) at a target frequency of 5 GHz. We also confirmed the correct function of multichannel JLDs, which were used as interface circuits in Josephson-CMOS hybrid memory, in a low-frequency test.

DOI
10.1109/tasc.2024.3508714

Related papers

A High-Speed Interface Based on a Josephson Latching Driver for Adiabatic Quantum-Flux-Parametron Logic

Fumihiro China, Naoki Takeuchi, Hideo Suzuki +3 more

The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.

IEICE Transactions on Electronics•Dec 2, 2021•3 citations

An interface circuit for a Josephson-CMOS hybrid digital system

Makoto Suzuki, Masaaki Maezawa, Hidetaka Takato +6 more

For broadband data communication between Josephson and CMOS digital systems, amplification of small Josephson-output signals and synchronization between the systems are important issues. We present an interface circuit for a Josephson-CMOS hybrid digital system. The interface circuit consists of a parallel-in-parallel-out (PIPO) circuit and built-in Josephson-MOS amplifiers. The PIPO circuit, implemented based on 4JL latching logic technology, performs synchronized data transfer between the Josephson and CMOS circuits. The Josephson-MOS amplifiers consists of stacked Josephson junctions (Suzuki stacks) and MOS inverters which are monolithically integrated on a chip. The circuits have been designed, fabricated and tested. We have successfully confirmed correct operation of the circuits.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•22 citations

A SFQ-to-CMOS Interface Circuit Based on SiGe BiCMOS for Josephson-CMOS Hybrid System

Zhichao Chen, Xingyu Zhang, Lixing You +1 more

Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.

Journal of Low Temperature Physics•Apr 1, 2025•1 citation

DC-biased Suzuki stack circuit for Josephson-CMOS memory applications

Yerzhan Mustafa, Keith Krause, Archit Shah +2 more

Abstract Josephson-CMOS hybrid memory leverages the high speed and low power operation of single-flux quantum logic and the high integration densities of CMOS technology. One of the commonly used type of interface circuits in Josephson-CMOS memory is a Suzuki stack, which is a latching high-voltage driver circuit. Suzuki stack circuits are typically powered by an AC bias voltage that has several limitations such as synchronization and coupling effects. To address these issues, a novel DC-biased Suzuki stack circuit is proposed in this paper. As compared to a conventional AC-biased Suzuki stack circuit, the proposed DC-biased design can provide similar output voltage levels and parameter margins, approximately two times higher operating frequency, and three orders of magnitude lower heat load of bias cables.

Superconductor Science and Technology•Jul 4, 2024•13 citations

Optimization of Suzuki Stack Circuit to Reduce Power Dissipation

Yerzhan Mustafa, Selçuk Köse

Superconductor–semiconductor hybrid circuits can combine the benefits of the high-speed and low-power operation of single-flux quantum circuits and high integration densities of CMOS technology such as memory. The Suzuki stack, a type of Josephson latching driver/amplifier, is a widely used interface circuit in Josephson–CMOS hybrid memories. Due to the limited cooling power at cryogenic temperatures, the power dissipation is becoming an important concern, especially in large-scale systems. An optimization technique to significantly reduce the power dissipation of Suzuki stack circuits is proposed in this article. The proposed design can reduce the power dissipation by 30–70% while causing a voltage drop of 2–9% in the output voltage depending on the circuit parameter configuration. The tradeoffs between the power dissipation and output voltage characteristics are discussed. The proposed design can operate correctly within at least$\pm$20% of process parameter variations as demonstrated with extensive simulations.

IEEE Transactions on Applied Superconductivity•Jul 19, 2022•16 citations

High-Speed Hybrid Superconductor-to-Semiconductor Interface Circuit With Ultra-Low Power Consumption

Thomas Ortlepp, Stephen R. Whiteley, Lizhen Zheng +2 more

Superconductor electronics for high-performance computing and high-speed analog-to-digital converters requires multi-channel digital data links. Most difficult is the amplification of the weak signals from the superconductor circuit to the volt level of semiconductor electronics. We developed a hybrid digital interface based on a Josephson latching driver, the so-called Suzuki stack, and a clocked CMOS comparator. The input can be directly triggered by a single flux quantum pulse and the output provides a 1 V CMOS-level signal. In contrast to existing systems, our interface is optimized for ultra-low-power consumption to enable its application for parallel multi-bit data interfaces. We provide evaluation of various types of Suzuki stacks and various CMOS comparators. We present experimental data on the delay of the overall hybrid interface and the total power consumption. The bit-error rate has been measured to be below 10-12. We will discuss the trade-off among circuit robustness, speed, and power consumption.

IEEE Transactions on Applied Superconductivity•Nov 14, 2012•21 citations
In this study, we designed, fabricated, and experimentally tested a Josephson latching driver (JLD), a superconductor-to-semiconductor interface circuit for use in Josephson-CMOS hybrid memory, utilizing a 10-kA/cm2Nb process. The JLD is composed of a voltage driver known as a Suzuki stack and a Josephson four-junction logic (4JL) gate that serves as a preamplifier. The basic structure is based on our previous design using the 2.5-kA/cm2Nb process. In this study, we optimized the critical current and the load resistance of the 4JL gate, taking into account the parameters of the Josephson junctions in the 10-kA/cm2process. In experiments with the fabricated test circuit, we confirmed the correct operation of the JLD (bit error rate−11) at a target frequency of 5 GHz. We also confirmed the correct function of multichannel JLDs, which were used as interface circuits in Josephson-CMOS hybrid memory, in a low-frequency test.
The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.
For broadband data communication between Josephson and CMOS digital systems, amplification of small Josephson-output signals and synchronization between the systems are important issues. We present an interface circuit for a Josephson-CMOS hybrid digital system. The interface circuit consists of a parallel-in-parallel-out (PIPO) circuit and built-in Josephson-MOS amplifiers. The PIPO circuit, implemented based on 4JL latching logic technology, performs synchronized data transfer between the Josephson and CMOS circuits. The Josephson-MOS amplifiers consists of stacked Josephson junctions (Suzuki stacks) and MOS inverters which are monolithically integrated on a chip. The circuits have been designed, fabricated and tested. We have successfully confirmed correct operation of the circuits.
Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.
Abstract Josephson-CMOS hybrid memory leverages the high speed and low power operation of single-flux quantum logic and the high integration densities of CMOS technology. One of the commonly used type of interface circuits in Josephson-CMOS memory is a Suzuki stack, which is a latching high-voltage driver circuit. Suzuki stack circuits are typically powered by an AC bias voltage that has several limitations such as synchronization and coupling effects. To address these issues, a novel DC-biased Suzuki stack circuit is proposed in this paper. As compared to a conventional AC-biased Suzuki stack circuit, the proposed DC-biased design can provide similar output voltage levels and parameter margins, approximately two times higher operating frequency, and three orders of magnitude lower heat load of bias cables.
Superconductor–semiconductor hybrid circuits can combine the benefits of the high-speed and low-power operation of single-flux quantum circuits and high integration densities of CMOS technology such as memory. The Suzuki stack, a type of Josephson latching driver/amplifier, is a widely used interface circuit in Josephson–CMOS hybrid memories. Due to the limited cooling power at cryogenic temperatures, the power dissipation is becoming an important concern, especially in large-scale systems. An optimization technique to significantly reduce the power dissipation of Suzuki stack circuits is proposed in this article. The proposed design can reduce the power dissipation by 30–70% while causing a voltage drop of 2–9% in the output voltage depending on the circuit parameter configuration. The tradeoffs between the power dissipation and output voltage characteristics are discussed. The proposed design can operate correctly within at least$\pm$20% of process parameter variations as demonstrated with extensive simulations.
Superconductor electronics for high-performance computing and high-speed analog-to-digital converters requires multi-channel digital data links. Most difficult is the amplification of the weak signals from the superconductor circuit to the volt level of semiconductor electronics. We developed a hybrid digital interface based on a Josephson latching driver, the so-called Suzuki stack, and a clocked CMOS comparator. The input can be directly triggered by a single flux quantum pulse and the output provides a 1 V CMOS-level signal. In contrast to existing systems, our interface is optimized for ultra-low-power consumption to enable its application for parallel multi-bit data interfaces. We provide evaluation of various types of Suzuki stacks and various CMOS comparators. We present experimental data on the delay of the overall hybrid interface and the total power consumption. The bit-error rate has been measured to be below 10-12. We will discuss the trade-off among circuit robustness, speed, and power consumption.