Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

National Science Review

Sub-millikelvin-resolved superconducting nanowire single-photon detector operates with sub-pW infrared radiation power

Qi Henry Chen, Fei Zhou, Chen Wei, Yue Dai, Haiyong Gan, Labao Zhang, Hao Eric Wang, Hang Yuan, Haochen Li, Jingrou Tan, Guojin Feng, Xuecou Tu, Xiaoqing Jia, Qingyuan Zhao, Lin Kang, Jian Chen, Peiheng Wu

Published Sep 14, 2024• 8 citations
Publisher

Abstract

The noise equivalent temperature difference (NETD) indicates the minimum temperature difference resolvable by using an infrared detector. The lower the NETD, the better the sensor can register small temperature differences. In this work, we proposed a strategy to achieve a high temperature resolution using a superconducting nanowire single-photon detector (SNSPD) with ultra-high sensitivity. We deduced the model for calculating the NETD of a photon-counting-type detector and applied it to our SNSPD-based set-up. Experimentally, we obtained an NETD as low as 0.65 mK, which is limited by the background radiation of the environment, and the required infrared radiation power is calculated to be <1 pW. Furthermore, the intrinsic NETD of this SNSPD is estimated to be <0.1 mK. This work demonstrated a sub-mK temperature resolution when using the SNSPD, paving the way for future remote infrared thermal imaging with high temperature resolution.

DOI
10.1093/nsr/nwae319

Related papers

UV superconducting nanowire single-photon detectors with high efficiency, low noise, and 4 K operating temperature

E. E. Wollman, V. B. Verma, A. D. Beyer +8 more

For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 μm in diameter, 70 - 80% efficiency at temperatures up to 4.2 K, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ∼ 0.25 counts/hr for a 56 μm diameter pixel. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.

arXiv:1708.04231•Optics Express•Oct 18, 2017•105 citations

Effect of temperature on superconducting nanowire single-photon detector noise

A. Bahgat Shehata, Alessandro Ruggeri, Franco Stellari +6 more

Today Superconducting Nanowire Single-Photon Detectors (SNSPDs) are commonly used in different photon-starved applications, including testing and diagnostics of VLSI circuits. Detecting very faint signals in the near-infrared wavelength range requires not only good detection efficiency, but also very low Dark Count Rate (DCR) and jitter. For example, low noise is crucial to enable ultra-low voltage optical testing of integrated circuits. The effect of detector temperature and background thermal radiation on the noise of superconducting single-photon detectors made of NbN meanders is studied in this paper. It is shown that two different regimes can be identified in the DCR vs. bias current characteristics. At high bias, the dark count rate is dominated by the intrinsic noise of the detector, while at low bias current it is dominated by the detection of stray photons that get onto the SNSPD. Changing the detector temperature changes its switching current and only affects the high bias branch of the characteristics: a reduction of the DCR can be achieved by lowering the SNSPD base temperature. On the other hand, changing the temperature of the single-photon light source (e.g. the VLSI circuit under test) only affects the low bias regime: a lower target temperature leads to a smaller DCR.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Aug 28, 2015•2 citations

Efficient mid-infrared single-photon detection using superconducting NbTiN nanowires with high time resolution in a Gifford-McMahon cryocooler

Jin Chang, Johannes W. N. Los, Ronan Gourgues +6 more

Shortly after their inception, superconducting nanowire single-photon detectors (SNSPDs) became the leading quantum light detection technology. With the capability of detecting single-photons with near-unity efficiency, high time resolution, low dark count rate, and fast recovery time, SNSPDs outperform conventional single-photon detection techniques. However, detecting lower energy single photons ( < 0.8 eV ) with high efficiency and low timing jitter has remained a challenge. To achieve unity internal efficiency at mid-infrared wavelengths, previous works used amorphous superconducting materials with low energy gaps at the expense of reduced time resolution (close to a nanosecond), and by operating them in complex milliKelvin (mK) dilution refrigerators. In this work, we provide an alternative approach with SNSPDs fabricated from 5 to 9.5 nm thick NbTiN superconducting films and devices operated in conventional Gifford-McMahon cryocoolers. By optimizing the superconducting film deposition process, film thickness, and nanowire design, our fiber-coupled devices achieved > 70 % system detection efficiency (SDE) at 2 μm and sub-15 ps timing jitter. Furthermore, detectors from the same batch demonstrated unity internal detection efficiency at 3 μm and 80% internal efficiency at 4 μm, paving the road for an efficient mid-infrared single-photon detection technology with unparalleled time resolution and without mK cooling requirements. We also systematically studied the dark count rates (DCRs) of our detectors coupled to different types of mid-infrared optical fibers and blackbody radiation filters. This offers insight into the trade-off between bandwidth and DCRs for mid-infrared SNSPDs. To conclude, this paper significantly extends the working wavelength range for SNSPDs made from polycrystalline NbTiN to 1.5–4 μm, and we expect quantum optics experiments and applications in the mid-infrared range to benefit from this far-reaching technology.

arXiv:2107.06354•Photonics Research•Jan 25, 2022•57 citations

Superconducting nanowire single-photon detectors: physics and applications

Chandra M. Natarajan, Michael G Tanner, Robert H. Hadfield

Single-photon detectors based on superconducting nanowires (SSPDs or SNSPDs) have rapidly emerged as a highly promising photon-counting technology for infrared wavelengths. These devices offer high efficiency, low dark counts and excellent timing resolution. In this review, we consider the basic SNSPD operating principle and models of device behaviour. We give an overview of the evolution of SNSPD device design and the improvements in performance which have been achieved. We also evaluate device limitations and noise mechanisms. We survey practical refrigeration technologies and optical coupling schemes for SNSPDs. Finally we summarize promising application areas, ranging from quantum cryptography to remote sensing. Our goal is to capture a detailed snapshot of an emerging superconducting detector technology on the threshold of maturity.

arXiv:1204.5560•Superconductor Science and Technology•Apr 4, 2012•1,092 citations

Temperature Dependent Performances of Superconducting Nanowire Single-Photon Detectors in an Ultralow-Temperature Region

Taro Yamashita, Shigehito Miki, Wei Qiu +3 more

We present the performances of a superconducting nanowire single-photon detector (SNSPD) in an ultralow-temperature region from 16 mK to 4 K. The system detection efficiency of the SNSPD showed saturation in the bias-current and temperature dependences, and reached the considerably high value of 15% for 100 Hz dark count rate below 1.4 K at a wavelength of 1550 nm even without an optical cavity structure. We found that the dark count exists even at 16 mK and black body radiation becomes its dominant origin in the low temperatures for fiber-coupled devices.

arXiv:1009.3981•Applied Physics Express•Sep 17, 2010•56 citations

NbN Superconducting Nanowire Single-Photon Detector With 90.5% Saturated System Detection Efficiency and 14.7 ps System Jitter at 1550 nm Wavelength

Xingyu Zhang, Weijun Zhang, Hui Zhou +8 more

Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.

IEEE Journal of Selected Topics in Quantum Electronics•Feb 23, 2022•27 citations
The noise equivalent temperature difference (NETD) indicates the minimum temperature difference resolvable by using an infrared detector. The lower the NETD, the better the sensor can register small temperature differences. In this work, we proposed a strategy to achieve a high temperature resolution using a superconducting nanowire single-photon detector (SNSPD) with ultra-high sensitivity. We deduced the model for calculating the NETD of a photon-counting-type detector and applied it to our SNSPD-based set-up. Experimentally, we obtained an NETD as low as 0.65 mK, which is limited by the background radiation of the environment, and the required infrared radiation power is calculated to be <1 pW. Furthermore, the intrinsic NETD of this SNSPD is estimated to be <0.1 mK. This work demonstrated a sub-mK temperature resolution when using the SNSPD, paving the way for future remote infrared thermal imaging with high temperature resolution.
For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 μm in diameter, 70 - 80% efficiency at temperatures up to 4.2 K, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ∼ 0.25 counts/hr for a 56 μm diameter pixel. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.
Today Superconducting Nanowire Single-Photon Detectors (SNSPDs) are commonly used in different photon-starved applications, including testing and diagnostics of VLSI circuits. Detecting very faint signals in the near-infrared wavelength range requires not only good detection efficiency, but also very low Dark Count Rate (DCR) and jitter. For example, low noise is crucial to enable ultra-low voltage optical testing of integrated circuits. The effect of detector temperature and background thermal radiation on the noise of superconducting single-photon detectors made of NbN meanders is studied in this paper. It is shown that two different regimes can be identified in the DCR vs. bias current characteristics. At high bias, the dark count rate is dominated by the intrinsic noise of the detector, while at low bias current it is dominated by the detection of stray photons that get onto the SNSPD. Changing the detector temperature changes its switching current and only affects the high bias branch of the characteristics: a reduction of the DCR can be achieved by lowering the SNSPD base temperature. On the other hand, changing the temperature of the single-photon light source (e.g. the VLSI circuit under test) only affects the low bias regime: a lower target temperature leads to a smaller DCR.
Shortly after their inception, superconducting nanowire single-photon detectors (SNSPDs) became the leading quantum light detection technology. With the capability of detecting single-photons with near-unity efficiency, high time resolution, low dark count rate, and fast recovery time, SNSPDs outperform conventional single-photon detection techniques. However, detecting lower energy single photons ( < 0.8 eV ) with high efficiency and low timing jitter has remained a challenge. To achieve unity internal efficiency at mid-infrared wavelengths, previous works used amorphous superconducting materials with low energy gaps at the expense of reduced time resolution (close to a nanosecond), and by operating them in complex milliKelvin (mK) dilution refrigerators. In this work, we provide an alternative approach with SNSPDs fabricated from 5 to 9.5 nm thick NbTiN superconducting films and devices operated in conventional Gifford-McMahon cryocoolers. By optimizing the superconducting film deposition process, film thickness, and nanowire design, our fiber-coupled devices achieved > 70 % system detection efficiency (SDE) at 2 μm and sub-15 ps timing jitter. Furthermore, detectors from the same batch demonstrated unity internal detection efficiency at 3 μm and 80% internal efficiency at 4 μm, paving the road for an efficient mid-infrared single-photon detection technology with unparalleled time resolution and without mK cooling requirements. We also systematically studied the dark count rates (DCRs) of our detectors coupled to different types of mid-infrared optical fibers and blackbody radiation filters. This offers insight into the trade-off between bandwidth and DCRs for mid-infrared SNSPDs. To conclude, this paper significantly extends the working wavelength range for SNSPDs made from polycrystalline NbTiN to 1.5–4 μm, and we expect quantum optics experiments and applications in the mid-infrared range to benefit from this far-reaching technology.
Single-photon detectors based on superconducting nanowires (SSPDs or SNSPDs) have rapidly emerged as a highly promising photon-counting technology for infrared wavelengths. These devices offer high efficiency, low dark counts and excellent timing resolution. In this review, we consider the basic SNSPD operating principle and models of device behaviour. We give an overview of the evolution of SNSPD device design and the improvements in performance which have been achieved. We also evaluate device limitations and noise mechanisms. We survey practical refrigeration technologies and optical coupling schemes for SNSPDs. Finally we summarize promising application areas, ranging from quantum cryptography to remote sensing. Our goal is to capture a detailed snapshot of an emerging superconducting detector technology on the threshold of maturity.
We present the performances of a superconducting nanowire single-photon detector (SNSPD) in an ultralow-temperature region from 16 mK to 4 K. The system detection efficiency of the SNSPD showed saturation in the bias-current and temperature dependences, and reached the considerably high value of 15% for 100 Hz dark count rate below 1.4 K at a wavelength of 1550 nm even without an optical cavity structure. We found that the dark count exists even at 16 mK and black body radiation becomes its dominant origin in the low temperatures for fiber-coupled devices.
Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.