Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1708.04231 · Optics Express

UV superconducting nanowire single-photon detectors with high efficiency, low noise, and 4 K operating temperature

E. E. Wollman, V. B. Verma, A. D. Beyer, R. M. Briggs, Boris A. Korzh, Jason P. Allmaras, Francesco Marsili, A. E. Lita, R. P. Mirin, S. W. Nam, Matthew D. Shaw

Published Oct 18, 2017• 101 citations
arXivHTMLPDF

Abstract

For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 μm in diameter, 70 - 80% efficiency at temperatures up to 4.2 K, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ∼ 0.25 counts/hr for a 56 μm diameter pixel. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.

DOI
10.1364/oe.25.026792

Related papers

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Next generation superconducting nanowire single-photon detectors

Kleanthis Erotokritou

Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.

•Jan 1, 2019•0 citations

Superconducting nanowire single-photon detectors for communication and fundamental physics applications

Jamie Luskin, Emma E. Wollman, Ekkehart Schmidt +9 more

Superconducting Nanowire Single Photon Detectors (SNSPDs) excel at a wide variety of performance criteria for single photon counting. They combine unprecedented high detection efficiency, high timing resolution, high count rates, low intrinsic dark count rates, and are sensitive to ultraviolet through mid-infrared single-photons. At JPL, we are working on several projects to push the performance limits of SNSPDs to achieve higher maximum count rates, larger active areas, higher timing resolution, and a wider spectral range. Our recent advances enable new applications for dark matter detection, imaging, and space-to-ground communication and provide insight into the fundamental physics of single-photon detection in superconducting nanowires.

Advanced Photon Counting Techniques•Apr 30, 2021•0 citations

High-efficiency, superconducting nanowire single-photon detectors from ultraviolet to infrared

Richard P. Mirin, Benedikt Hampel, Adriana E. Lita +6 more

Superconducting nanowire single-photon detectors (SNSPDs) have demonstrated outstanding performance metrics over a wide range of wavelengths, from the ultraviolet to the long-wave infrared (LWIR). System detection efficiencies approach 100% at specific wavelengths with very low dark count rates and low timing jitter. Recent experiments such as time-resolved photoluminescence of mid-IR emitting semiconductors and integration of SNSPDs with ion traps will be described.

IEEE Photonics Conference•Nov 12, 2023•0 citations

A superconducting nanowire single-photon detector system for single-photon source characterization

Catherine R. M. Fitzpatrick, Chandra M. Natarajan, Ryan E. Warburton +8 more

Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 20, 2010•0 citations

Superconducting nanowire single photon detectors for optical communication and astronomy

Matthew D. Shaw

Superconducting Nanowire Single Photon Detectors (SNSPDs) are the most advanced detectors available for time-resolved single photon counting from the UV to the mid-infrared. We will discuss recent progress in SNSPD development for the ground terminal in NASA’s Deep Space Optical Communication (DSOC) project as well as recent performance advances in other metrics, including the development of kilopixel SNSPD arrays, single-photon sensitivity at mid-infrared wavelengths as long as 10 microns, and SNSPDs with sub-3ps timing jitter. I will discuss a range of new potential scientific applications for SNSPDs, including exoplanet transit spectroscopy, dark matter detection, fluorescence lifetime imaging microscopy, and quantum information science.

X-Ray, Optical, and Infrared Detectors for Astronomy•Dec 14, 2020•1 citation
For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 μm in diameter, 70 - 80% efficiency at temperatures up to 4.2 K, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ∼ 0.25 counts/hr for a 56 μm diameter pixel. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
Superconducting Nanowire Single Photon Detectors (SNSPDs) excel at a wide variety of performance criteria for single photon counting. They combine unprecedented high detection efficiency, high timing resolution, high count rates, low intrinsic dark count rates, and are sensitive to ultraviolet through mid-infrared single-photons. At JPL, we are working on several projects to push the performance limits of SNSPDs to achieve higher maximum count rates, larger active areas, higher timing resolution, and a wider spectral range. Our recent advances enable new applications for dark matter detection, imaging, and space-to-ground communication and provide insight into the fundamental physics of single-photon detection in superconducting nanowires.
Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.
Superconducting Nanowire Single Photon Detectors (SNSPDs) are the most advanced detectors available for time-resolved single photon counting from the UV to the mid-infrared. We will discuss recent progress in SNSPD development for the ground terminal in NASA’s Deep Space Optical Communication (DSOC) project as well as recent performance advances in other metrics, including the development of kilopixel SNSPD arrays, single-photon sensitivity at mid-infrared wavelengths as long as 10 microns, and SNSPDs with sub-3ps timing jitter. I will discuss a range of new potential scientific applications for SNSPDs, including exoplanet transit spectroscopy, dark matter detection, fluorescence lifetime imaging microscopy, and quantum information science.