Quantum computing is a rapidly evolving field with potential for solving complex problems beyond the reach of classical computers. Scalability in qubit design and signal processing architecture within cryostats is necessary for taking advantage of quantum computing's potential. Current state of the art qubit technology requires both a feed and readout line for each qubit within a quantum processor, with these lines generally being metallic coaxial cables. For stainless steel cables this represents a significant heat load into the cryostat. An alternative approach involves using optical fibers for signal transmission, as optical fibers have a thermal conductivity two orders of magnitude lower than stainless steel coaxial cables. The proposed method for optical signal transmission relies on electro-optic modulation, where a voltage applied to an electro-optic material changes its refractive index, allowing for a controllable phase change to be applied to any light passing through the material. This concept can be combined with on-chip photonic waveguide technology to build fiber-coupled phase modulators as well as intensity modulators using on chip interferometers. The proposed architecture uses a room temperature intensity modulator to encode microwave signals onto a laser signal, which is recovered at cryogenic temperatures using a photodiode and used as input for a device under test. The output of the test device is encoded onto light using a phase modulator and recovered at room temperature through interferometry. Proof-of-concept experiments have been carried out at room temperature, including noise characterization and preliminary tests of components at cryogenic temperatures.
Quantum computing is a rapidly evolving field with potential for solving complex problems beyond the reach of classical computers. Scalability in qubit design and signal processing architecture within cryostats is necessary for taking advantage of quantum computing's potential. Current state of the art qubit technology requires both a feed and readout line for each qubit within a quantum processor, with these lines generally being metallic coaxial cables. For stainless steel cables this represents a significant heat load into the cryostat. An alternative approach involves using optical fibers for signal transmission, as optical fibers have a thermal conductivity two orders of magnitude lower than stainless steel coaxial cables. The proposed method for optical signal transmission relies on electro-optic modulation, where a voltage applied to an electro-optic material changes its refractive index, allowing for a controllable phase change to be applied to any light passing through the material. This concept can be combined with on-chip photonic waveguide technology to build fiber-coupled phase modulators as well as intensity modulators using on chip interferometers. The proposed architecture uses a room temperature intensity modulator to encode microwave signals onto a laser signal, which is recovered at cryogenic temperatures using a photodiode and used as input for a device under test. The output of the test device is encoded onto light using a phase modulator and recovered at room temperature through interferometry. Proof-of-concept experiments have been carried out at room temperature, including noise characterization and preliminary tests of components at cryogenic temperatures.
Abstract Encoding information onto optical fields using electro-optical modulation is the backbone of modern telecommunication networks, offering vast bandwidth and low-loss transport via optical fibers. For these reasons, optical fibers are also replacing electrical cables for short range communications within data centers. Compared to electrical coaxial cables, optical fibers also introduce two orders of magnitude smaller heat load from room to milli-Kelvin temperatures, making optical interconnects based on electro-optical modulation an attractive candidate for interfacing superconducting quantum circuits and hybrid superconducting devices. Yet, little is known about optical modulation at cryogenic temperatures. Here we demonstrate a proof-of-principle cryogenic electro-optical interconnect, showing that currently employed Ti-doped lithium niobate phase modulators are compatible with operation down to 800mK ---below the typical operation temperature of conventional microwave amplifiers based on high electron mobility transistors (HEMTs)---and maintain their room temperature Pockels coefficient. We utilize cryogenic electro-optical modulation to perform spectroscopy of a superconducting circuit optomechanical system, measuring optomechanically induced transparency (OMIT). In addition, we encode thermomechanical sidebands from the microwave domain onto an optical signal processed at room temperature. Although the currently achieved noise figure is significantly higher than that of a typical HEMT, substantial noise reduction should be attainable by harnessing recent advances in integrated modulators, by increasing the modulator length, or by using materials with a higher electro-optic coefficient, leading to noise levels on par with HEMTs. Our work highlights the potential of electro-optical modulators for massively parallel readout for emerging quantum computing or cryogenic classical computing platforms.
With the rapid development of superconducting quantum computing and the implementation of surface code, large-scale quantum computing is emerging as an urgent demand. In a superconducting computing system, the qubit is maintained in a cryogenic environment to avoid thermal excitation. Thus, the transmission of control signals, which are generated at room temperature, is needed. Typically, the transmission of these signals to the qubit relies on a coaxial cable wiring approach. However, in a large-scale computing system with hundreds or even thousands of qubits, the coaxial cables will pose great space and heat load to the dilution refrigerator. Here, to tackle this problem, we propose and demonstrate a direct-modulation-based optical transmission line. In our experiment, the average single-qubit XEB error and control error are measured as 0.139% and 0.014% separately, demonstrating the feasibility of the optical wiring approach and paving the way for large-scale superconducting quantum computing.
Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.
Superconducting quantum circuits operate at millikelvin temperatures, typically requiring independent microwave cables for each qubit for connecting room-temperature control and readout electronics. However, scaling to large-scale processors hosting hundreds of qubits faces a severe input/output (I/O) bottleneck, as the dense cable arrays impose prohibitive constraints on physical footprint, thermal load, wiring complexity, and cost. Here we demonstrate a complete optical I/O architecture for superconducting quantum circuits, in which all control and readout signals are transmitted exclusively via optical photons. Employing a broadband traveling-wave Brillouin microwave-to-optical transducer, we achieve simultaneous frequency-multiplexed optical readout of two qubits. Combined with fiber-integrated photodiode arrays for control signal delivery, this closed-loop optical I/O introduces no measurable degradation to qubit coherence times, with an optically driven single-qubit gate fidelity showing only a 0.19% reduction relative to standard microwave operation. These results establish optical interconnects as a viable path toward large-scale superconducting quantum processors, and open the possibility of networking multiple superconducting quantum computers housed in separate dilution refrigerators through a centralized room-temperature control infrastructure.
Superconducting circuits exhibit remarkable potential for constructing large-scale quantum simulation and computation systems, featuring numerous qubits, extended coherence time, and precise control. Nevertheless, the growing number of signal cables poses a challenge in dilution refrigerators due to space and heat load constraints. To overcome this issue, we experimentally implemented an optically-assisted transmission line as an alternative to coaxial cables. By modulating microwave signals on laser intensities at room temperature and regenerating the signals at a cryogenic plate within the dilution refrigerator, we demonstrated full control of superconducting qubits using photocurrent. We demonstrate and benchmark both single-qubit and two-qubit gates on frequency tunable transmon qubits, achieving fidelities of 99.915% ± 0.005% and 99.676% ± 0.041%, respectively, which have reached the requirement of the surface code.
In recent years, standard CMOS microprocessors have approached their maximum power dissipation per unit area, effectively placing a limit on computational power. This highlights the urgent need to explore alternative technologies. One promising avenue is the use of superconductors, which demonstrate zero resistivity below a critical temperature. However, circuits based on superconductors necessitate the use of cryostats to maintain low temperatures, presenting challenges in data transfer with the room temperature environment. While coaxial cables are often employed for this purpose, they suffer from limited data transfer rates and contribute significantly to heat load. On the contrary, photonics integrated circuits (PICs) coupled with optical fibers present a viable solution. They enable scalable, cost-effective, and power-efficient optical interconnections capable of supporting high data transfer rates while minimizing heat transfer. In this presentation, We will discuss the latest advancements in cryogenic PICs, focusing on their application in interfacing with cryogenic computing systems such as single-flux-quantum logic circuits and superconducting qubits.