Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2004.04705 · Nature Electronics

A cryogenic electro-optic interconnect for superconducting devices

Amir Youssefi, Itay Shomroni, Yash J. Joshi, Nathan Bernier, Anton Lukashchuk, Philipp Uhrich, Liu Qiu, Tobias Jan Kippenberg

Published May 10, 2021• 112 citations
arXivHTMLPDF
DOI
10.1038/s41928-021-00570-4

Related papers

Cryogenic electro-optic interconnect for superconducting circuits

Itay Shomroni, Amir Youssefi, Nathan Bernier +3 more

Bulletin of the American Physical Society•Mar 4, 2020•0 citations

Cryogenic electro-optic interconnect for superconducting devices

Tobias Jan Kippenberg, Amir Youssefi, Itay Shomroni +5 more

Abstract Encoding information onto optical fields using electro-optical modulation is the backbone of modern telecommunication networks, offering vast bandwidth and low-loss transport via optical fibers. For these reasons, optical fibers are also replacing electrical cables for short range communications within data centers. Compared to electrical coaxial cables, optical fibers also introduce two orders of magnitude smaller heat load from room to milli-Kelvin temperatures, making optical interconnects based on electro-optical modulation an attractive candidate for interfacing superconducting quantum circuits and hybrid superconducting devices. Yet, little is known about optical modulation at cryogenic temperatures. Here we demonstrate a proof-of-principle cryogenic electro-optical interconnect, showing that currently employed Ti-doped lithium niobate phase modulators are compatible with operation down to 800mK ---below the typical operation temperature of conventional microwave amplifiers based on high electron mobility transistors (HEMTs)---and maintain their room temperature Pockels coefficient. We utilize cryogenic electro-optical modulation to perform spectroscopy of a superconducting circuit optomechanical system, measuring optomechanically induced transparency (OMIT). In addition, we encode thermomechanical sidebands from the microwave domain onto an optical signal processed at room temperature. Although the currently achieved noise figure is significantly higher than that of a typical HEMT, substantial noise reduction should be attainable by harnessing recent advances in integrated modulators, by increasing the modulator length, or by using materials with a higher electro-optic coefficient, leading to noise levels on par with HEMTs. Our work highlights the potential of electro-optical modulators for massively parallel readout for emerging quantum computing or cryogenic classical computing platforms.

•Aug 17, 2020•14 citations

Cryogenic optical data link for superconducting circuits

Paolo Pintus, Mo Soltani, Galan Moody

Nature Photonics•Apr 1, 2024•7 citations

Superconducting Electronics and Devices

J.C. Gallop, Luning Hao, J.C. Macfarlane

Taylor & Francis, Inc. eBooks•Oct 1, 2007•1 citation

All-optical superconducting qubit readout

Georg Arnold, Thomas Werner, Rishabh Sahu +3 more

The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.

arXiv:2310.16817•Nature Physics•Feb 11, 2025•38 citations

In-situ electro-optic sampling of microwave signals under cryogenic conditions and for superconducting applications

Shekhar Priyadarshi, Ferizaj, Rinis, Oliver Kieler +8 more

We demonstrate a cryogenic electro-optic sampling (EOS) setup that allows for the measurement of microwave signals at arbitrary positions on a cryogenic chip-scale device. We use a Josephson Arbitrary Waveform Synthesizer (JAWS) to generate quantum-accurate voltage signals and measure them with the EOS setup, allowing for the calibration of its response, yielding traceability of the microwave measurements to a quantum standard. We use the EOS setup to determine the time-domain response of ultrafast cryogenic photodiodes and the electrical reflection coefficient, i.e., the S11 scattering parameter, in a superconducting transmission line. Finally, we introduce an optical femtosecond pulse source which can be used to study the fidelity of superconducting transmission lines and terminations, as well as reflections from elements like Josephson junction arrays imbedded in them.

arXiv:2411.00162•Oct 31, 2024•0 citations
Abstract Encoding information onto optical fields using electro-optical modulation is the backbone of modern telecommunication networks, offering vast bandwidth and low-loss transport via optical fibers. For these reasons, optical fibers are also replacing electrical cables for short range communications within data centers. Compared to electrical coaxial cables, optical fibers also introduce two orders of magnitude smaller heat load from room to milli-Kelvin temperatures, making optical interconnects based on electro-optical modulation an attractive candidate for interfacing superconducting quantum circuits and hybrid superconducting devices. Yet, little is known about optical modulation at cryogenic temperatures. Here we demonstrate a proof-of-principle cryogenic electro-optical interconnect, showing that currently employed Ti-doped lithium niobate phase modulators are compatible with operation down to 800mK ---below the typical operation temperature of conventional microwave amplifiers based on high electron mobility transistors (HEMTs)---and maintain their room temperature Pockels coefficient. We utilize cryogenic electro-optical modulation to perform spectroscopy of a superconducting circuit optomechanical system, measuring optomechanically induced transparency (OMIT). In addition, we encode thermomechanical sidebands from the microwave domain onto an optical signal processed at room temperature. Although the currently achieved noise figure is significantly higher than that of a typical HEMT, substantial noise reduction should be attainable by harnessing recent advances in integrated modulators, by increasing the modulator length, or by using materials with a higher electro-optic coefficient, leading to noise levels on par with HEMTs. Our work highlights the potential of electro-optical modulators for massively parallel readout for emerging quantum computing or cryogenic classical computing platforms.
The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.
We demonstrate a cryogenic electro-optic sampling (EOS) setup that allows for the measurement of microwave signals at arbitrary positions on a cryogenic chip-scale device. We use a Josephson Arbitrary Waveform Synthesizer (JAWS) to generate quantum-accurate voltage signals and measure them with the EOS setup, allowing for the calibration of its response, yielding traceability of the microwave measurements to a quantum standard. We use the EOS setup to determine the time-domain response of ultrafast cryogenic photodiodes and the electrical reflection coefficient, i.e., the S11 scattering parameter, in a superconducting transmission line. Finally, we introduce an optical femtosecond pulse source which can be used to study the fidelity of superconducting transmission lines and terminations, as well as reflections from elements like Josephson junction arrays imbedded in them.