Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2512.21199

All-optical control and multiplexed readout of multiple superconducting qubits

Xiaoxuan Pan, Chuanlong Ma, Jia-Qi Wang, Zheng-Xu Zhu, Linze Li, Jiajun Chen, Yuan-Hao Yang, Yilong Zhou, Jia-Hua Zou, Xin-Biao Xu, Weiting Wang, Baile Chen, Haifeng Yu, Chang-Ling Zou, Luyan Sun

quant-phphysics.opticsSubmitted Dec 24, 2025• Announced Dec 25, 2025• 0 citations
arXivHTMLPDF

Abstract

Superconducting quantum circuits operate at millikelvin temperatures, typically requiring independent microwave cables for each qubit for connecting room-temperature control and readout electronics. However, scaling to large-scale processors hosting hundreds of qubits faces a severe input/output (I/O) bottleneck, as the dense cable arrays impose prohibitive constraints on physical footprint, thermal load, wiring complexity, and cost. Here we demonstrate a complete optical I/O architecture for superconducting quantum circuits, in which all control and readout signals are transmitted exclusively via optical photons. Employing a broadband traveling-wave Brillouin microwave-to-optical transducer, we achieve simultaneous frequency-multiplexed optical readout of two qubits. Combined with fiber-integrated photodiode arrays for control signal delivery, this closed-loop optical I/O introduces no measurable degradation to qubit coherence times, with an optically driven single-qubit gate fidelity showing only a 0.19% reduction relative to standard microwave operation. These results establish optical interconnects as a viable path toward large-scale superconducting quantum processors, and open the possibility of networking multiple superconducting quantum computers housed in separate dilution refrigerators through a centralized room-temperature control infrastructure.

Comments
7 pages, 4 figures

Related papers

High fidelity control of superconducting qubits with optical transmitted signal

Yu-Huai Li, Daojin Fan, Na Li +15 more

Superconducting circuits exhibit remarkable potential for constructing large-scale quantum simulation and computation systems, featuring numerous qubits, extended coherence time, and precise control. Nevertheless, the growing number of signal cables poses a challenge in dilution refrigerators due to space and heat load constraints. To overcome this issue, we experimentally implemented an optically-assisted transmission line as an alternative to coaxial cables. By modulating microwave signals on laser intensities at room temperature and regenerating the signals at a cryogenic plate within the dilution refrigerator, we demonstrated full control of superconducting qubits using photocurrent. We demonstrate and benchmark both single-qubit and two-qubit gates on frequency tunable transmon qubits, achieving fidelities of 99.915% $\pm$ 0.005% and 99.676% $\pm$ 0.041%, respectively, which have reached the requirement of the surface code.

quant-pharXiv:2608.19602•Aug 21, 2026•0 citations

Scalable Optical Links for Controlling Bosonic Quantum Processors

Chuanlong Ma, Jia-Qi Wang, Linze Li +13 more

Superconducting quantum computing has the potential to revolutionize computational capabilities. However, scaling up large quantum processors is limited by the cumbersome and heat-conductive electronic cables that connect room-temperature control electronics to quantum processors, leading to significant signal attenuation. Optical fibers provide a promising solution, but their use has been restricted to controlling simple two-level quantum systems over short distances. Here, we demonstrate optical control of a bosonic quantum processor, achieving universal operations on the joint Hilbert space of a transmon qubit and a storage cavity. Using an array of cryogenic fiber-integrated uni-traveling-carrier photodiodes, we prepare Fock states containing up to ten photons. Additionally, remote control of bosonic modes over a transmission distance of 15 km has been achieved, with fidelities exceeding 95%. The combination of high-dimensional quantum control, multi-channel operation, and long-distance transmission addresses the key requirements for scaling superconducting quantum computers and enables architectures for distributed quantum data centers.

quant-pharXiv:2512.10706•Dec 12, 2025•0 citations

Interfacing Superconducting Qubits with Light

Piero Chiappina

Superconducting quantum circuits are a leading hardware candidate for realizing a large-scale fault-tolerant quantum computer. However, scaling superconducting quantum computers will soon approach the physical limits imposed by their cryogenic operating environments. Consequently, interconnects between multiple processor modules will become increasingly necessary for scaling quantum computers. Optical fiber is a particularly promising candidate for these interconnects due to its low loss and negligible thermal noise at room temperature. However, interfacing microwave-frequency superconducting circuits with optical fibers presents several challenges. In this thesis, we present a modular architecture which addresses many of the current challenges in building this interface. We develop an optomechanical quantum transducer which is capable of generating microwave- and optical-frequency photons in pairs, and demonstrate quantum entanglement between these microwave-optical photon pairs. Further, we develop a superconducting qubit module optimized for efficient absorption of itinerant microwave photons, and demonstrate a high-efficiency photon catch protocol. Finally, we connect the superconducting qubit module to the transducer module via a superconducting microwave cable. We drive the microwave-optical photon pair generation process in the transducer module and employ the photon catch protocol in the qubit module to facilitate state transfer between the qubit and the flying microwave photon from the transducer. We observe correlations between the final qubit state and the detection of an optical photon, demonstrating a crucial step toward establishing quantum entanglement between superconducting qubits and light. We discuss ongoing progress and challenges in realizing hybrid entanglement and in extending this approach to entangle remote superconducting qubits over optical networks.

•Aug 19, 2026•0 citations

A kilometer photonic link connecting superconducting circuits in two dilution refrigerators

Yiyu Zhou, Yufeng Wu, Chunzhen Li +4 more

Superconducting quantum processors are a leading platform for implementing practical quantum computation algorithms. Although superconducting quantum processors with hundreds of qubits have been demonstrated, their further scaling up is constrained by the physical size and cooling power of dilution refrigerators. This constraint can be overcome by constructing a quantum network to interconnect qubits hosted in different refrigerators, which requires microwave-to-optical transducers to enable low-loss signal transmission over long distances. Despite that various designs and demonstrations have achieved high-efficiency and low-added-noise transducers, a coherent photonic link between separate refrigerators has not yet been realized. In this work, we experimentally demonstrate coherent signal transfer between two superconducting circuits housed in separate dilution refrigerators, enabled by a pair of frequency-matched aluminum nitride electro-optic transducers connected via a 1-km telecom optical fiber. With transducers at each node achieving >0.1% efficiency, an overall 80 dB improvement in transduction efficiency over commercial electro-optic modulators is attainable, paving the way towards a fully quantum-enabled link. This work provides critical design guidelines towards scalable superconducting quantum networks interconnected by photonic links.

arXiv:2508.02444•Aug 4, 2025•0 citations

Electro-Optical Control and Readout of Superconducting Devices

Calum Rose, Natale G. Pruiti, Daniel Kelly +3 more

Quantum computing is a rapidly evolving field with potential for solving complex problems beyond the reach of classical computers. Scalability in qubit design and signal processing architecture within cryostats is necessary for taking advantage of quantum computing's potential. Current state of the art qubit technology requires both a feed and readout line for each qubit within a quantum processor, with these lines generally being metallic coaxial cables. For stainless steel cables this represents a significant heat load into the cryostat. An alternative approach involves using optical fibers for signal transmission, as optical fibers have a thermal conductivity two orders of magnitude lower than stainless steel coaxial cables. The proposed method for optical signal transmission relies on electro-optic modulation, where a voltage applied to an electro-optic material changes its refractive index, allowing for a controllable phase change to be applied to any light passing through the material. This concept can be combined with on-chip photonic waveguide technology to build fiber-coupled phase modulators as well as intensity modulators using on chip interferometers. The proposed architecture uses a room temperature intensity modulator to encode microwave signals onto a laser signal, which is recovered at cryogenic temperatures using a photodiode and used as input for a device under test. The output of the test device is encoded onto light using a phase modulator and recovered at room temperature through interferometry. Proof-of-concept experiments have been carried out at room temperature, including noise characterization and preliminary tests of components at cryogenic temperatures.

IEEE International Conference on Quantum Computing and Engineering (QCE)•Sep 17, 2023•0 citations

All-optical superconducting qubit readout

Georg Arnold, Thomas Werner, Rishabh Sahu +3 more

The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.

arXiv:2310.16817•Nature Physics•Feb 11, 2025•38 citations
Superconducting quantum circuits operate at millikelvin temperatures, typically requiring independent microwave cables for each qubit for connecting room-temperature control and readout electronics. However, scaling to large-scale processors hosting hundreds of qubits faces a severe input/output (I/O) bottleneck, as the dense cable arrays impose prohibitive constraints on physical footprint, thermal load, wiring complexity, and cost. Here we demonstrate a complete optical I/O architecture for superconducting quantum circuits, in which all control and readout signals are transmitted exclusively via optical photons. Employing a broadband traveling-wave Brillouin microwave-to-optical transducer, we achieve simultaneous frequency-multiplexed optical readout of two qubits. Combined with fiber-integrated photodiode arrays for control signal delivery, this closed-loop optical I/O introduces no measurable degradation to qubit coherence times, with an optically driven single-qubit gate fidelity showing only a 0.19% reduction relative to standard microwave operation. These results establish optical interconnects as a viable path toward large-scale superconducting quantum processors, and open the possibility of networking multiple superconducting quantum computers housed in separate dilution refrigerators through a centralized room-temperature control infrastructure.
Superconducting circuits exhibit remarkable potential for constructing large-scale quantum simulation and computation systems, featuring numerous qubits, extended coherence time, and precise control. Nevertheless, the growing number of signal cables poses a challenge in dilution refrigerators due to space and heat load constraints. To overcome this issue, we experimentally implemented an optically-assisted transmission line as an alternative to coaxial cables. By modulating microwave signals on laser intensities at room temperature and regenerating the signals at a cryogenic plate within the dilution refrigerator, we demonstrated full control of superconducting qubits using photocurrent. We demonstrate and benchmark both single-qubit and two-qubit gates on frequency tunable transmon qubits, achieving fidelities of 99.915% ±\pm± 0.005% and 99.676% ±\pm± 0.041%, respectively, which have reached the requirement of the surface code.
Superconducting quantum computing has the potential to revolutionize computational capabilities. However, scaling up large quantum processors is limited by the cumbersome and heat-conductive electronic cables that connect room-temperature control electronics to quantum processors, leading to significant signal attenuation. Optical fibers provide a promising solution, but their use has been restricted to controlling simple two-level quantum systems over short distances. Here, we demonstrate optical control of a bosonic quantum processor, achieving universal operations on the joint Hilbert space of a transmon qubit and a storage cavity. Using an array of cryogenic fiber-integrated uni-traveling-carrier photodiodes, we prepare Fock states containing up to ten photons. Additionally, remote control of bosonic modes over a transmission distance of 15 km has been achieved, with fidelities exceeding 95%. The combination of high-dimensional quantum control, multi-channel operation, and long-distance transmission addresses the key requirements for scaling superconducting quantum computers and enables architectures for distributed quantum data centers.
Superconducting quantum circuits are a leading hardware candidate for realizing a large-scale fault-tolerant quantum computer. However, scaling superconducting quantum computers will soon approach the physical limits imposed by their cryogenic operating environments. Consequently, interconnects between multiple processor modules will become increasingly necessary for scaling quantum computers. Optical fiber is a particularly promising candidate for these interconnects due to its low loss and negligible thermal noise at room temperature. However, interfacing microwave-frequency superconducting circuits with optical fibers presents several challenges. In this thesis, we present a modular architecture which addresses many of the current challenges in building this interface. We develop an optomechanical quantum transducer which is capable of generating microwave- and optical-frequency photons in pairs, and demonstrate quantum entanglement between these microwave-optical photon pairs. Further, we develop a superconducting qubit module optimized for efficient absorption of itinerant microwave photons, and demonstrate a high-efficiency photon catch protocol. Finally, we connect the superconducting qubit module to the transducer module via a superconducting microwave cable. We drive the microwave-optical photon pair generation process in the transducer module and employ the photon catch protocol in the qubit module to facilitate state transfer between the qubit and the flying microwave photon from the transducer. We observe correlations between the final qubit state and the detection of an optical photon, demonstrating a crucial step toward establishing quantum entanglement between superconducting qubits and light. We discuss ongoing progress and challenges in realizing hybrid entanglement and in extending this approach to entangle remote superconducting qubits over optical networks.
Superconducting quantum processors are a leading platform for implementing practical quantum computation algorithms. Although superconducting quantum processors with hundreds of qubits have been demonstrated, their further scaling up is constrained by the physical size and cooling power of dilution refrigerators. This constraint can be overcome by constructing a quantum network to interconnect qubits hosted in different refrigerators, which requires microwave-to-optical transducers to enable low-loss signal transmission over long distances. Despite that various designs and demonstrations have achieved high-efficiency and low-added-noise transducers, a coherent photonic link between separate refrigerators has not yet been realized. In this work, we experimentally demonstrate coherent signal transfer between two superconducting circuits housed in separate dilution refrigerators, enabled by a pair of frequency-matched aluminum nitride electro-optic transducers connected via a 1-km telecom optical fiber. With transducers at each node achieving >0.1% efficiency, an overall 80 dB improvement in transduction efficiency over commercial electro-optic modulators is attainable, paving the way towards a fully quantum-enabled link. This work provides critical design guidelines towards scalable superconducting quantum networks interconnected by photonic links.
Quantum computing is a rapidly evolving field with potential for solving complex problems beyond the reach of classical computers. Scalability in qubit design and signal processing architecture within cryostats is necessary for taking advantage of quantum computing's potential. Current state of the art qubit technology requires both a feed and readout line for each qubit within a quantum processor, with these lines generally being metallic coaxial cables. For stainless steel cables this represents a significant heat load into the cryostat. An alternative approach involves using optical fibers for signal transmission, as optical fibers have a thermal conductivity two orders of magnitude lower than stainless steel coaxial cables. The proposed method for optical signal transmission relies on electro-optic modulation, where a voltage applied to an electro-optic material changes its refractive index, allowing for a controllable phase change to be applied to any light passing through the material. This concept can be combined with on-chip photonic waveguide technology to build fiber-coupled phase modulators as well as intensity modulators using on chip interferometers. The proposed architecture uses a room temperature intensity modulator to encode microwave signals onto a laser signal, which is recovered at cryogenic temperatures using a photodiode and used as input for a device under test. The output of the test device is encoded onto light using a phase modulator and recovered at room temperature through interferometry. Proof-of-concept experiments have been carried out at room temperature, including noise characterization and preliminary tests of components at cryogenic temperatures.
The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.