Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Optical Amplifiers

Shiva Kumar, M. Jamal Deen

Published Apr 11, 2014• 0 citations
Publisher

Abstract

This chapter focuses mainly on three types of optical amplifiers: (1) the semiconductor optical amplifier (SOA), (2) the erbium-doped fibers amplifier, and (3) the Raman amplifier. In each case, the physical principles, governing equations, noise amplifications, and practical applications are discussed. The chapter considers a simple amplifier model in which the amplifier magnifies the input power by a factor of G and adds white noise. Impact of amplified spontaneous emission (ASE) noise in two-level systems is also discussed.

DOI
10.1002/9781118684207.ch6

Related papers

Optimum noise performance of optical amplifiers

H. A. Haus

The concept of noise figure F and noise measure M applicable to radio frequency and microwave amplifiers is reviewed and extended to cover optical amplifiers. Two noise figures are defined in the optical regime: one gives the ASE output, while the other gives the ratio of signal-to-noise ratios at the input and output. In the quantum regime, the lower limit on these optimum values is set by a generalization of Heisenberg's uncertainty relation. A Raman back-pumped fiber link with post-amplification with an erbium-doped fiber amplifier is used to illustrate the use of noise measure.

IEEE Journal of Quantum Electronics•Jun 1, 2001•16 citations

Quantum Noise in Optical Amplifiers

Kyo Inoue

Noise is one of the basic characteristics of optical amplifiers. Whereas there are various noise sources, the intrinsic one is quantum noise that originates from Heisenberg’s uncertainty principle. This chapter describes quantum noise in optical amplifiers, including population-inversion–based amplifiers such as an Erbium-doped fiber amplifier and a semiconductor optical amplifier, and optical parametric amplifiers. A full quantum mechanical treatment is developed based on Heisenberg equation of motion for quantum mechanical operators. The results provide the quantum mechanical basis for a classical picture of amplifier noise widely used in the optical communication field.

InTech eBooks•Jul 25, 2018•5 citations

Noise in optical amplifiers

Gianfranco Cariolaro, Roberto Corvaja, Pierluigi Franco +2 more

This article presents an application of a recently published probablistic model for traveling wave optical amplification. Both optical signal and amplified spontaneous emission (ASE) noise are modeled as bunches of photons traveling along the amplifying region with size varying according to simple random rules. The results of the theory enable one to obtain a complete and accurate characterization of the signal and noise counting at the amplifier output. On the basis of the above statistics, we find a realistic evaluation of the limits imposed by both quantum and ASE noise on the performances of a receiver including an optical amplifier at a preamplifier stage.

Fiber & Integrated Optics•Jan 1, 1994•2 citations

Laser Amplifiers

Bahaa E. A. Saleh, Malvin Carl Teich

A coherent optical amplifier is a device that increases the amplitude of an optical field while maintaining its phase. If the optical field at the input to such an amplifier is monochromatic, the output will also be monochromatic, with the same frequency. The output amplitude is increased relative to the input while the phase is unchanged or shifted by a fixed amount. In contrast, an amplifier that increases the intensity of an optical wave without preserving the phase is called an incoherent optical amplifier. This chapter is concerned with coherent optical amplifiers. Such amplifiers are important for various applications; examples include the amplification of weak optical pulses such as those that have traveled through a long length of optical fiber, and the production of highly intense optical pulses such as those required for laser-fusion applications. Furthermore, it is important to understand the principles underlying the operation of optical amplifiers as a prelude to the discussion of optical oscillators. Light transmitted through matter in thermal equilibrium is attenuated rather than amplified. This is because absorption by the large population of atoms in the lower energy level is more prevalent than stimulated emission by the smaller population of atoms in the upper level. An essential ingredient for achieving laser amplification is the presence of a greater number of atoms in the upper energy level than in the lower level, which is clearly a nonequilibrium situation. Achieving such a population inversion requires a source of power to excite (pump) the atoms into the higher energy level. Although the presentation throughout this chapter is couched in terms of “atoms” and “atomic levels,” these appelations are to be more broadly understood as “active medium” and “laser energy levels,” respectively. The properties of an ideal (optical or electronic) coherent amplifier are displayed schematically. Real coherent amplifiers deliver a gain and phase shift that are frequency dependent, typically in the manner illustrated here. The gain and phase shift constitute the amplifier's transfer function. For a sufficiently high input amplitude, furthermore, real amplifiers may exhibit saturation, a form of nonlinear behavior in which the output amplitude fails to increase in proportion to the input amplitude. Saturation introduces harmonic components into the output, provided that the amplifier bandwidth is sufficiently broad to pass them. Real amplifiers also introduce noise, so that a randomly fluctuating component is always present at the output, regardless of the input. An amplifier may therefore be characterized by the following features: ▪ gain; ▪ bandwidth; ▪ phase shift; ▪ power source; ▪ nonlinearity and gain saturation, and ▪ noise We proceed to discuss these characteristics in turn in this chapter. The theory of laser amplification is developed, leading to expressions for the amplifier gain, spectral bandwidth, and phase shift. The mechanisms by which an amplifier power source can achieve a population inversion are examined. Gain saturation and noise in the amplification process, are discussed respectively. This chapter relies on material presented in Chap. 12.

Wiley eBooks•Aug 14, 1991•2 citations

Amplification of an optical pulse sequence in semiconductor optical amplifiers

Todor N. Arabadzhiev, Ivan M. Uzunov

The semiconductor optical amplifiers (SOA) are a base component in the fiber-optic transmission lines. We investigate the interaction with optical pulses of the Traveling Wave (TW) SOA having a typical parameters originated from a semi-classical model of two-level systems. An application of TW SOA as in-line amplifier for an optical pulses sequence and received "pattern" effect is shown.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 6, 2003•0 citations

Spectral gain modeling of optical amplifiers: Spectral effects and non-linear distributed gain in the optical amplification medium

Stefano Bottacchi

Introduction In this chapter we will present the theory of spectral gain in optical amplifiers and the related optical power distribution. The concepts are general, as they apply to every optical amplifier configuration, independent of the specific architecture and implementation technology. We will configure the optical amplifying medium as a traveling-wave device, where the optical field undergoes optical amplification as it propagates from the input to the output sections. Generally speaking, optical amplification is achieved by a net stimulated emission process. Referring to a generic section z of infinitesimal thickness dz , optical gain is determined by the imbalance between net stimulated emission and cavity losses, including extrinsic absorption, reflection and radiated fields. As we know from the theory of light amplification in the three-level atomic system presented in Chapter 5, stimulated absorption of photons is governed by the same transition rate as stimulated emission, and is included in the net stimulated emission process. With this in mind, we note the identity between stimulated emission and the stimulated absorption rates, Γ 12 = Γ 21 , and the net stimulated photon term Γ[ j 2 ( t ) – j 1 ( t )] p ( t ) in the rate equation. In order to develop the traveling-wave model, the photon density becomes a function of the longitudinal position 0 ≤ z ≤ L along the amplifier medium. Accordingly, we will set p ( t , z ) as the relative density of stimulated photons per unit volume (0 ≤ p ( t , z ) ≤ 1) at time t and section z . When photons with appropriate energy proceed along the amplifying medium, they are amplified by means of net stimulated emission. At some section z = z 0 , the steady-state photon density P ( z ) can approach the saturation density P sat ( z ).

Cambridge University Press eBooks•Sep 6, 2014•0 citations
This chapter focuses mainly on three types of optical amplifiers: (1) the semiconductor optical amplifier (SOA), (2) the erbium-doped fibers amplifier, and (3) the Raman amplifier. In each case, the physical principles, governing equations, noise amplifications, and practical applications are discussed. The chapter considers a simple amplifier model in which the amplifier magnifies the input power by a factor of G and adds white noise. Impact of amplified spontaneous emission (ASE) noise in two-level systems is also discussed.
The concept of noise figure F and noise measure M applicable to radio frequency and microwave amplifiers is reviewed and extended to cover optical amplifiers. Two noise figures are defined in the optical regime: one gives the ASE output, while the other gives the ratio of signal-to-noise ratios at the input and output. In the quantum regime, the lower limit on these optimum values is set by a generalization of Heisenberg's uncertainty relation. A Raman back-pumped fiber link with post-amplification with an erbium-doped fiber amplifier is used to illustrate the use of noise measure.
Noise is one of the basic characteristics of optical amplifiers. Whereas there are various noise sources, the intrinsic one is quantum noise that originates from Heisenberg’s uncertainty principle. This chapter describes quantum noise in optical amplifiers, including population-inversion–based amplifiers such as an Erbium-doped fiber amplifier and a semiconductor optical amplifier, and optical parametric amplifiers. A full quantum mechanical treatment is developed based on Heisenberg equation of motion for quantum mechanical operators. The results provide the quantum mechanical basis for a classical picture of amplifier noise widely used in the optical communication field.
This article presents an application of a recently published probablistic model for traveling wave optical amplification. Both optical signal and amplified spontaneous emission (ASE) noise are modeled as bunches of photons traveling along the amplifying region with size varying according to simple random rules. The results of the theory enable one to obtain a complete and accurate characterization of the signal and noise counting at the amplifier output. On the basis of the above statistics, we find a realistic evaluation of the limits imposed by both quantum and ASE noise on the performances of a receiver including an optical amplifier at a preamplifier stage.
A coherent optical amplifier is a device that increases the amplitude of an optical field while maintaining its phase. If the optical field at the input to such an amplifier is monochromatic, the output will also be monochromatic, with the same frequency. The output amplitude is increased relative to the input while the phase is unchanged or shifted by a fixed amount. In contrast, an amplifier that increases the intensity of an optical wave without preserving the phase is called an incoherent optical amplifier. This chapter is concerned with coherent optical amplifiers. Such amplifiers are important for various applications; examples include the amplification of weak optical pulses such as those that have traveled through a long length of optical fiber, and the production of highly intense optical pulses such as those required for laser-fusion applications. Furthermore, it is important to understand the principles underlying the operation of optical amplifiers as a prelude to the discussion of optical oscillators. Light transmitted through matter in thermal equilibrium is attenuated rather than amplified. This is because absorption by the large population of atoms in the lower energy level is more prevalent than stimulated emission by the smaller population of atoms in the upper level. An essential ingredient for achieving laser amplification is the presence of a greater number of atoms in the upper energy level than in the lower level, which is clearly a nonequilibrium situation. Achieving such a population inversion requires a source of power to excite (pump) the atoms into the higher energy level. Although the presentation throughout this chapter is couched in terms of “atoms” and “atomic levels,” these appelations are to be more broadly understood as “active medium” and “laser energy levels,” respectively. The properties of an ideal (optical or electronic) coherent amplifier are displayed schematically. Real coherent amplifiers deliver a gain and phase shift that are frequency dependent, typically in the manner illustrated here. The gain and phase shift constitute the amplifier's transfer function. For a sufficiently high input amplitude, furthermore, real amplifiers may exhibit saturation, a form of nonlinear behavior in which the output amplitude fails to increase in proportion to the input amplitude. Saturation introduces harmonic components into the output, provided that the amplifier bandwidth is sufficiently broad to pass them. Real amplifiers also introduce noise, so that a randomly fluctuating component is always present at the output, regardless of the input. An amplifier may therefore be characterized by the following features: ▪ gain; ▪ bandwidth; ▪ phase shift; ▪ power source; ▪ nonlinearity and gain saturation, and ▪ noise We proceed to discuss these characteristics in turn in this chapter. The theory of laser amplification is developed, leading to expressions for the amplifier gain, spectral bandwidth, and phase shift. The mechanisms by which an amplifier power source can achieve a population inversion are examined. Gain saturation and noise in the amplification process, are discussed respectively. This chapter relies on material presented in Chap. 12.
Introduction In this chapter we will present the theory of spectral gain in optical amplifiers and the related optical power distribution. The concepts are general, as they apply to every optical amplifier configuration, independent of the specific architecture and implementation technology. We will configure the optical amplifying medium as a traveling-wave device, where the optical field undergoes optical amplification as it propagates from the input to the output sections. Generally speaking, optical amplification is achieved by a net stimulated emission process. Referring to a generic section z of infinitesimal thickness dz , optical gain is determined by the imbalance between net stimulated emission and cavity losses, including extrinsic absorption, reflection and radiated fields. As we know from the theory of light amplification in the three-level atomic system presented in Chapter 5, stimulated absorption of photons is governed by the same transition rate as stimulated emission, and is included in the net stimulated emission process. With this in mind, we note the identity between stimulated emission and the stimulated absorption rates, Γ 12 = Γ 21 , and the net stimulated photon term Γ[ j 2 ( t ) – j 1 ( t )] p ( t ) in the rate equation. In order to develop the traveling-wave model, the photon density becomes a function of the longitudinal position 0 ≤ z ≤ L along the amplifier medium. Accordingly, we will set p ( t , z ) as the relative density of stimulated photons per unit volume (0 ≤ p ( t , z ) ≤ 1) at time t and section z . When photons with appropriate energy proceed along the amplifying medium, they are amplified by means of net stimulated emission. At some section z = z 0 , the steady-state photon density P ( z ) can approach the saturation density P sat ( z ).