A coherent optical amplifier is a device that increases the amplitude of an optical field while maintaining its phase. If the optical field at the input to such an amplifier is monochromatic, the output will also be monochromatic, with the same frequency. The output amplitude is increased relative to the input while the phase is unchanged or shifted by a fixed amount. In contrast, an amplifier that increases the intensity of an optical wave without preserving the phase is called an incoherent optical amplifier. This chapter is concerned with coherent optical amplifiers. Such amplifiers are important for various applications; examples include the amplification of weak optical pulses such as those that have traveled through a long length of optical fiber, and the production of highly intense optical pulses such as those required for laser-fusion applications. Furthermore, it is important to understand the principles underlying the operation of optical amplifiers as a prelude to the discussion of optical oscillators. Light transmitted through matter in thermal equilibrium is attenuated rather than amplified. This is because absorption by the large population of atoms in the lower energy level is more prevalent than stimulated emission by the smaller population of atoms in the upper level. An essential ingredient for achieving laser amplification is the presence of a greater number of atoms in the upper energy level than in the lower level, which is clearly a nonequilibrium situation. Achieving such a population inversion requires a source of power to excite (pump) the atoms into the higher energy level. Although the presentation throughout this chapter is couched in terms of “atoms” and “atomic levels,” these appelations are to be more broadly understood as “active medium” and “laser energy levels,” respectively. The properties of an ideal (optical or electronic) coherent amplifier are displayed schematically. Real coherent amplifiers deliver a gain and phase shift that are frequency dependent, typically in the manner illustrated here. The gain and phase shift constitute the amplifier's transfer function. For a sufficiently high input amplitude, furthermore, real amplifiers may exhibit saturation, a form of nonlinear behavior in which the output amplitude fails to increase in proportion to the input amplitude. Saturation introduces harmonic components into the output, provided that the amplifier bandwidth is sufficiently broad to pass them. Real amplifiers also introduce noise, so that a randomly fluctuating component is always present at the output, regardless of the input. An amplifier may therefore be characterized by the following features: ▪ gain; ▪ bandwidth; ▪ phase shift; ▪ power source; ▪ nonlinearity and gain saturation, and ▪ noise We proceed to discuss these characteristics in turn in this chapter. The theory of laser amplification is developed, leading to expressions for the amplifier gain, spectral bandwidth, and phase shift. The mechanisms by which an amplifier power source can achieve a population inversion are examined. Gain saturation and noise in the amplification process, are discussed respectively. This chapter relies on material presented in Chap. 12.
A coherent optical amplifier is a device that increases the amplitude of an optical field while maintaining its phase. If the optical field at the input to such an amplifier is monochromatic, the output will also be monochromatic, with the same frequency. The output amplitude is increased relative to the input while the phase is unchanged or shifted by a fixed amount. In contrast, an amplifier that increases the intensity of an optical wave without preserving the phase is called an incoherent optical amplifier. This chapter is concerned with coherent optical amplifiers. Such amplifiers are important for various applications; examples include the amplification of weak optical pulses such as those that have traveled through a long length of optical fiber, and the production of highly intense optical pulses such as those required for laser-fusion applications. Furthermore, it is important to understand the principles underlying the operation of optical amplifiers as a prelude to the discussion of optical oscillators. Light transmitted through matter in thermal equilibrium is attenuated rather than amplified. This is because absorption by the large population of atoms in the lower energy level is more prevalent than stimulated emission by the smaller population of atoms in the upper level. An essential ingredient for achieving laser amplification is the presence of a greater number of atoms in the upper energy level than in the lower level, which is clearly a nonequilibrium situation. Achieving such a population inversion requires a source of power to excite (pump) the atoms into the higher energy level. Although the presentation throughout this chapter is couched in terms of “atoms” and “atomic levels,” these appelations are to be more broadly understood as “active medium” and “laser energy levels,” respectively. The properties of an ideal (optical or electronic) coherent amplifier are displayed schematically. Real coherent amplifiers deliver a gain and phase shift that are frequency dependent, typically in the manner illustrated here. The gain and phase shift constitute the amplifier's transfer function. For a sufficiently high input amplitude, furthermore, real amplifiers may exhibit saturation, a form of nonlinear behavior in which the output amplitude fails to increase in proportion to the input amplitude. Saturation introduces harmonic components into the output, provided that the amplifier bandwidth is sufficiently broad to pass them. Real amplifiers also introduce noise, so that a randomly fluctuating component is always present at the output, regardless of the input. An amplifier may therefore be characterized by the following features: ▪ gain; ▪ bandwidth; ▪ phase shift; ▪ power source; ▪ nonlinearity and gain saturation, and ▪ noise We proceed to discuss these characteristics in turn in this chapter. The theory of laser amplification is developed, leading to expressions for the amplifier gain, spectral bandwidth, and phase shift. The mechanisms by which an amplifier power source can achieve a population inversion are examined. Gain saturation and noise in the amplification process, are discussed respectively. This chapter relies on material presented in Chap. 12.
Introduction In this chapter we will present the theory of spectral gain in optical amplifiers and the related optical power distribution. The concepts are general, as they apply to every optical amplifier configuration, independent of the specific architecture and implementation technology. We will configure the optical amplifying medium as a traveling-wave device, where the optical field undergoes optical amplification as it propagates from the input to the output sections. Generally speaking, optical amplification is achieved by a net stimulated emission process. Referring to a generic section z of infinitesimal thickness dz , optical gain is determined by the imbalance between net stimulated emission and cavity losses, including extrinsic absorption, reflection and radiated fields. As we know from the theory of light amplification in the three-level atomic system presented in Chapter 5, stimulated absorption of photons is governed by the same transition rate as stimulated emission, and is included in the net stimulated emission process. With this in mind, we note the identity between stimulated emission and the stimulated absorption rates, Γ 12 = Γ 21 , and the net stimulated photon term Γ[ j 2 ( t ) – j 1 ( t )] p ( t ) in the rate equation. In order to develop the traveling-wave model, the photon density becomes a function of the longitudinal position 0 ≤ z ≤ L along the amplifier medium. Accordingly, we will set p ( t , z ) as the relative density of stimulated photons per unit volume (0 ≤ p ( t , z ) ≤ 1) at time t and section z . When photons with appropriate energy proceed along the amplifying medium, they are amplified by means of net stimulated emission. At some section z = z 0 , the steady-state photon density P ( z ) can approach the saturation density P sat ( z ).
We were able to show in Chapter 3 that a medium in which we can obtain a population inversion (i.e. a situation in which the population density in the excited state is greater than that in the fundamental level) allows for optical gain of an electromagnetic wave having a frequency near to the resonant frequency of the system. By introducing feedback of the amplified signal into the medium, the system can be made to oscillate naturally, resulting in laser oscillations. To obtain this population inversion, we must introduce at least a third (and perhaps even a fourth) energy level into the system. (We saw how a two-level system under the influence of an intense pump beam will saturate with no resulting population inversion.) The aim then of this chapter is to introduce the concepts necessary to extend our two-level system into a working model capable of illustrating the phenomenon of laser oscillation. We will not spend too much time discussing atomic transition lasers as they do not figure readily in our treatment of quantum electronic properties of semiconductors. An exception will be made, however; we brush upon the particular topics of a diode pumped laser in Complement 4.E and a quantum cascade laser in Complement 13.H.
The intensity fluctuations in the output of a saturable optical amplifier are studied as the amplifier length is increased. Characteristics are determined by calculation of the diagonal elements of the density matrix of the optical field. Saturation affecting both upper-state and lower-state atomic populations is considered. Spontaneous emission distributed along the amplifier causes the "photon-number" distribution to approach a Bose-Einstein distribution during linear amplification if the input field is not Bose-Einstein. The onset of saturation reduces the relative fluctuations of the optical field both by introducing nonlinear gain and by reducing the spontaneous emission. Limiting solutions show that strong saturation leads to a major reduction in the fluctuations causing the photon-number distribution to approach a Poisson distribution.
The fundamental source of noise in laser and optical amplifier is spontaneous emission. However, it is possible to reduce this noise by preparing the gain medium (atoms) in coherent superposition of states. There are essentially two schemes for generating atomic coherence in optical amplifiers. \n \nFirst scheme involves the preparation of atoms in a coherent superposition of states before injecting them inside the cavity. In the other scheme atoms (initially pumped incoherently) are continuously driven by an external pump field inside the cavity. Almost all the studies concerning the quenching of spontaneous emission noise in optical amplifiers, based on the notion of atomic coherent superposition, ignore the finite bandwidth of the field that is responsible for generating coherence. In this dissertation, we have examined the effect of the finite bandwidth associated with the phase fluctuations of the driving field on a number of noise quenching schemes. \n \nIt is known that coherent preparation of atoms can, under certain conditions, lead to noise-free amplification and almost 50 percent phase squeezing in a two-photon correlated emission laser. We study the effect of phase fluctuations in the injected atoms on the phase noise of the field in these systems. We discuss the conditions under which squeezing is preserved in the two-photon linear amplifiers. We also show that, even for very large phase fluctuations in the injected atoms, almost 50 percent phase squeezing can be achieved. The corresponding gain is however significantly reduced. \n \nWe also study a system of phase-sensitive amplifier where atoms are prepared in a coherent superposition of states by a strong classical field. We study the role of pump phase fluctuations associated with the finite linewidth on the quantum statistical properties of the radiation field. A study of output field characteristics reveals that the presence of a weak pump field gives rise to equal variances in both the field quadratures which are independent of linewidth. On the other hand, the presence of strong pump field alters the output field characteristics with the generation of squeezing which is later on destroyed due to the presence of phase fluctuations
We examine application of optical amplification to coherent lidar for the case of a weak return signal (a number of quanta of the return optical field close to unity). We consider the option that has been explored to date, namely, incorporation of an optical amplifier operated in a linear manner located after reception of the signal and immediately prior to heterodyning and photodetection. We also consider alternative strategies where the coherent interaction, the nonlinear processes, and the amplification are not necessarily constrained to occur in the manner investigated to date. We include the complications that occur because of mechanisms that occur at the level of a few, or one, quantum excitation. Two factors combine in the work to date that limit the value of the approach. These are: (1) the weak signal tends to require operation of the amplifier in the linear regime where the important advantages of nonlinear optical processing are not accessed, (2) the linear optical amplifier has a -3dB noise figure (SN(out)/SN(in)) that necessarily degrades the signal. Some improvement is gained because the gain provided by the optical amplifier can be used to overcome losses in the heterodyned process and photodetection. The result, however, is that introduction of an optical amplifier in a well optimized coherent lidar system results in, at best, a modest improvement in signal to noise. Some improvement may also be realized on incorporating more optical components in a coherent lidar system for purely practical reasons. For example, more compact, lighter weight, components, more robust alignment, or more rapid processing may be gained. We further find that there remain a number of potentially valuable, but unexplored options offered both by the rapidly expanding base of optical technology and the recent investigation of novel nonlinear coherent interference phenomena occurring at the single quantum excitation level. Key findings are: (1) insertion of linear optical amplifiers in well optimized conventional lidar systems offers modest improvements, at best, (2) the practical advantages of optical amplifiers, especially fiber amplifiers, such as ease of alignment, compactness, efficiency, lightweight, etc., warrant further investigation for coherent lidar, (3) the possibility of more fully optical lidar systems should be explored, (4) advantages gained by use of coherent interference of optical fields at the level of one, or a few, signal quanta should be explored, (5) amplification without inversion, population trapping, and use of electromagnetic induced transparency warrant investigation in connection with coherent lidar, (6) these new findings are probably more applicable to earth related NASA work, although applications to deep space should not be excluded, and (7) our own work in the Ultrafast Laboratory at UAH along some of the above lines of investigation, may be useful.
The analysis in Chapter 3 used a phenomenological form of the permittivity to describe active materials. A proper understanding of optical amplification requires a quantum-mechanical approach for describing the interaction of light with atoms of an active medium [1]. However, even a relatively simple atom such as hydrogen or helium allows so many energy transitions that its full description is intractable even with modern computing machinery [2, 3]. The only solution is to look for idealized models that contain the most essential features of a realistic system. The semiclassical two-level-atom model has proven to be quite successful in this respect [4]. Even though a real atom has infinitely many energy levels, two energy levels whose energy difference nearly matches the photon energy suffice to understand the interaction dynamics when the atom interacts with nearly monochromatic radiation. Moreover, if the optical field contains a sufficiently large number of photons (> 100), it can be treated classically using a set of optical Bloch equations. In this chapter, we learn the underlying physical concepts behind the optical Bloch equations. We apply these equations in subsequent chapters to actual optical amplifiers and show that they can be solved analytically under certain conditions to provide a realistic description of optical amplifiers.