Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

dc SQUID's I–V Characteristics and Its Bias Modes

Yi Zhang, Hui Dong, Hans-Joachim Krause, Guofeng Zhang, Xiaoming Xie

Published May 29, 2020• 0 citations
Publisher

Abstract

The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.

DOI
10.1002/9783527816514.ch3

Related papers

Bias conditions of dc-SQUID for a time-domain SQUID multiplexer

J. Beyer, D. Drung, K. D. Irwin

We have analyzed the biasing of the first-stage dc superconducting quantum interference devices (SQUIDs) of a time-domain dc-SQUID multiplexer (SQUID MUX) and find that the bias conditions of first-stage SQUIDs significantly affect the performance of the SQUID MUX in terms of total multiplexer noise and bandwidth. We present an experimental study of the operational parameters of a first-stage SQUID under varied bias conditions. Our measurements include a direct determination of the first-stage SQUID dynamic resistance RDYN1 and the flux noise of the first-stage SQUID biased over the range from voltage bias to current bias. Our measurements show that matching the bias resistors RS1 of the first-stage SQUIDs to RDYN1 improves the SQUID MUX noise performance as well as the first-stage bandwidth.

Review of Scientific Instruments•Jan 26, 2004•4 citations

Stray capacitance effect in superconducting quantum interferometers

Roberto Leoni, P. Carelli, Vittorio Foglietti

The experimental results obtained with low noise dc superconducting quantum interference devices (dc-SQUIDs) are sometimes not well understood. In particular, when the critical current is high, very irregular voltage versus flux characteristics can be measured. On the other hand, when the critical current is low, the characteristics follow perfectly the resistively shunted junction model. We have studied the dynamics of a dc-SQUID in the presence of stray capacitance and shunting resistors imbalance. The equations describing a circuit model for this physical system are integrated numerically and the results are compared with voltage versus flux characteristics obtained from fabricated devices. We find that the theoretical analysis accounts very well for previously misunderstood experimental features of the dc-SQUID. This model can give more physical sense to the various regimes of behavior of the dc-SQUID giving more insight into the experimental results.

Journal of Applied Physics•Sep 1, 1988•6 citations

Tunable narrow-linewidth oscillations and current-voltage characteristics of a resistive dc SQUID

J. M. V. Verschueren, A. A. Uiterwaal, Rob W. van der Heijden +1 more

The output voltage of a dc superconducting quantum interference device (SQUID) containing a resistive section Rs oscillates at a frequency νq =Vs/ φ0 (φ0=flux quantum) when a current controlled voltage Vs is maintained across Rs. These oscillations have been observed from ∼10−1 to 1011 Hz, using Rs values ranging from ∼10−10 to ∼10−3 Ω in low inductance (∼10−10 H) point contact SQUID loops. At high frequencies, they manifest themselves in the dc current-voltage characteristics by inducing extra current steps.

Applied Physics Letters•Jul 15, 1983•12 citations

Tracing the characteristics of a flux qubit with a hysteretic dc-superconducting quantum interference device comparator

Maria Gabriella Castellano, F. Chiarello, Roberto Leoni +6 more

A hysteretic dc-superconducting quantum interference device (SQUID) is used to trace the flux characteristic of a tunable rf-SQUID, the basic element for the realization of superconducting flux qubits. This allows important simplifications of circuitry and electronics in developing devices for quantum computing, by eliminating the necessity of more complex magnetometers. A hysteretic dc-SQUID is usually operated as a comparator, distinguishing only which one of two adjacent flux states is occupied by the rf-SQUID. The necessary sensitivity, moreover, is usually reached only at temperatures in the mK range. However, by exploiting the statistical properties of the current–voltage curve in the region where the switching from the zero-voltage state occurs, it is possible to obtain an accurate tracing of the input flux, even at a relatively high temperature (a few Kelvin). In our case, the input signal is given by the internal flux of a tunable rf-SQUID, the building block of a flux qubit.

Journal of Applied Physics•Dec 4, 2003•4 citations

An insight into voltage-biased superconducting quantum interference devices

Chao Liu, Yi Zhang, Michael Mück +5 more

We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.

Applied Physics Letters•Nov 26, 2012•20 citations

Flux modulation scheme for direct current SQUID readout revisited

Tao Hong, Hai Wang, Yi Zhang +5 more

The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.

Applied Physics Letters•Feb 8, 2016•4 citations
The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.
We have analyzed the biasing of the first-stage dc superconducting quantum interference devices (SQUIDs) of a time-domain dc-SQUID multiplexer (SQUID MUX) and find that the bias conditions of first-stage SQUIDs significantly affect the performance of the SQUID MUX in terms of total multiplexer noise and bandwidth. We present an experimental study of the operational parameters of a first-stage SQUID under varied bias conditions. Our measurements include a direct determination of the first-stage SQUID dynamic resistance RDYN1 and the flux noise of the first-stage SQUID biased over the range from voltage bias to current bias. Our measurements show that matching the bias resistors RS1 of the first-stage SQUIDs to RDYN1 improves the SQUID MUX noise performance as well as the first-stage bandwidth.
The experimental results obtained with low noise dc superconducting quantum interference devices (dc-SQUIDs) are sometimes not well understood. In particular, when the critical current is high, very irregular voltage versus flux characteristics can be measured. On the other hand, when the critical current is low, the characteristics follow perfectly the resistively shunted junction model. We have studied the dynamics of a dc-SQUID in the presence of stray capacitance and shunting resistors imbalance. The equations describing a circuit model for this physical system are integrated numerically and the results are compared with voltage versus flux characteristics obtained from fabricated devices. We find that the theoretical analysis accounts very well for previously misunderstood experimental features of the dc-SQUID. This model can give more physical sense to the various regimes of behavior of the dc-SQUID giving more insight into the experimental results.
The output voltage of a dc superconducting quantum interference device (SQUID) containing a resistive section Rs oscillates at a frequency νq =Vs/ φ0 (φ0=flux quantum) when a current controlled voltage Vs is maintained across Rs. These oscillations have been observed from ∼10−1 to 1011 Hz, using Rs values ranging from ∼10−10 to ∼10−3 Ω in low inductance (∼10−10 H) point contact SQUID loops. At high frequencies, they manifest themselves in the dc current-voltage characteristics by inducing extra current steps.
A hysteretic dc-superconducting quantum interference device (SQUID) is used to trace the flux characteristic of a tunable rf-SQUID, the basic element for the realization of superconducting flux qubits. This allows important simplifications of circuitry and electronics in developing devices for quantum computing, by eliminating the necessity of more complex magnetometers. A hysteretic dc-SQUID is usually operated as a comparator, distinguishing only which one of two adjacent flux states is occupied by the rf-SQUID. The necessary sensitivity, moreover, is usually reached only at temperatures in the mK range. However, by exploiting the statistical properties of the current–voltage curve in the region where the switching from the zero-voltage state occurs, it is possible to obtain an accurate tracing of the input flux, even at a relatively high temperature (a few Kelvin). In our case, the input signal is given by the internal flux of a tunable rf-SQUID, the building block of a flux qubit.
We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.
The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.