Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Stray capacitance effect in superconducting quantum interferometers

Roberto Leoni, P. Carelli, Vittorio Foglietti

Published Sep 1, 1988• 6 citations
Publisher

Abstract

The experimental results obtained with low noise dc superconducting quantum interference devices (dc-SQUIDs) are sometimes not well understood. In particular, when the critical current is high, very irregular voltage versus flux characteristics can be measured. On the other hand, when the critical current is low, the characteristics follow perfectly the resistively shunted junction model. We have studied the dynamics of a dc-SQUID in the presence of stray capacitance and shunting resistors imbalance. The equations describing a circuit model for this physical system are integrated numerically and the results are compared with voltage versus flux characteristics obtained from fabricated devices. We find that the theoretical analysis accounts very well for previously misunderstood experimental features of the dc-SQUID. This model can give more physical sense to the various regimes of behavior of the dc-SQUID giving more insight into the experimental results.

DOI
10.1063/1.341636

Related papers

Performance of dc SQUIDs with resistively shunted inductance

Vittorio Foglietti, W. J. Gallagher, M. B. Ketchen +3 more

We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.

Applied Physics Letters•Oct 2, 1989•45 citations

Asymmetry in the LC resonance characteristic in dc superconducting quantum interference devices: New method of observing pair-quasiparticle interference in superconducting tunnel junctions

Y. Song

The $\mathrm{LC}$ (inductance-capacitance) resonance phenomenon in the dc SQUID (superconducting quantum interference device) creates a current peak in the $I\ensuremath{-}V$ characteristics at a voltage determined by the resonance frequency. These $I\ensuremath{-}V$ characteristics have been analyzed with the resistively shunted Josephson-junction model in the low-damping and small-oscillation regime. The resonance $I\ensuremath{-}V$ characteristics contain sufficient information to determine all circuit parameters for the dc SQUID's. Specifically, we can apply this analysis to symmetric, tunnel-junction dc SQUID's to deduce the pair-quasiparticle interference conductance ($cos\ensuremath{\theta}$ term).

Physical review. B, Condensed matter•Sep 1, 1981•0 citations

Effect of parasitic capacitance and inductance on the dynamics and noise of dc superconducting quantum interference devices

Tapani Ryhänen, Heikki Seppä, R. Cantor

Practical thin-film dc superconducting quantum interference devices (SQUIDs) are often built with an integrated input coil which leads to the formation of various parasitic elements. We have designed and fabricated several square washer-shaped dc SQUID test devices with various amounts of parasitic capacitance formed by covering the washer slits with superconducting coverplates of various widths. In the simplest approximation, the parasitic capacitance Cp appears entirely across the Josephson junctions; in a better approximation, Cp divides the total inductance into two parts, an effective SQUID loop inductance L and a small parasitic inductance Lp. For both models, noise-free and noise-rounded current-voltage and voltage-flux characteristics are calculated for various values of the ratios L/Lp and Cp/C, where C is the Josephson junction capacitance. The SQUID dynamics are significantly affected by Cp and Lp. The energy resolution ε at first deteriorates with increasing Cp for Cp/C ≲ 2, but as Cp/C becomes large, ε improves to less than twice the value for Cp/C ≊ 0. The optimal points of operation for large Cp, however, are found at voltages above the low-frequency resonance determined by L and Cp where the flux-to-voltage transfer function is low. Furthermore, for devices with Cp/C ≫ 1 and Lp≠0, the double-loop geometry leads to an additional resonance determined by Lp and C that appears at high frequencies. The energy resolution inside this high-frequency resonance is nearly independent of Cp and comparable to the energy resolution of a device having the same total inductance but with Cp/C ≪ 1. Extensive noise mappings on several different test devices have been carried out using a computer-controlled measurement system. The measured characteristics and noise performance are shown to be in good agreement with the simulations.

Journal of Applied Physics•Jun 15, 1992•32 citations

Superconducting quantum interference device with frequency-dependent damping: Readout of flux qubits

Timothy L. Robertson, B. L. T. Plourde, T. Hime +4 more

Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance ${C}_{s}$ and resistance ${R}_{s}$ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.

Physical Review B•Jul 11, 2005•23 citations

Experimental Study of Noise Characteristics of Large-β dc SQUID with Resistively Shunted Inductance

Satoshi Kohjiro, Keiji Enpuku, Keiji Yoshida +1 more

Noise characteristics of dc SQUIDs in large β regimes have been studied experimentally in the case when a SQUID inductance is resistively shunted. Here, β=2L I 0/Φ0 is the modulation parameter, L is the SQUID inductance, I 0 is the critical current of the Josephson junction and Φ0 is the flux quantum. It is shown experimentally that the performance of the SQUID does not degrade significantly even for large β values; for example, the minimum energy resolution of the SQUID is as small as ε=25h and the flux region where ε<50h is as wide as 0.1Φ0, even for the case β=12, where h is the Planck constant. The experimental results agree quantitatively with the theoretical ones.

Japanese Journal of Applied Physics•Oct 1, 1988•8 citations

The current–voltage characteristics of the resistive direct current superconducting quantum interference device

Ya. S. Greenberg, G.S. Krivoy, H. Koch

Partly resistive superconducting quantum interference devices (RSQUIDs) are used in noise thermometry in the liquid helium temperature range. Here we analyze one type of RSQUID that has not been thoroughly investigated until now: the direct current biased with two Josephson junctions and a resistive part connected in series with the junctions and closed by a superconducting ring. The resistive shunted model of the Josephson junctions is used for the analysis. Two cases of the RSQUID ring inductance were analyzed: (i) negligibly small and (ii) small but finite inductance. The expressions for the low frequency output signal, the current–voltage (I–V) characteristics, and the current flowing through the resistive part are obtained. In the dependence of the output frequency versus the dc current passed through the resistive part often an offset is observed experimentally. This phenomenon can be explained as an influence of an asymmetry in the critical currents of the junctions.

Journal of Applied Physics•Feb 15, 1997•9 citations
The experimental results obtained with low noise dc superconducting quantum interference devices (dc-SQUIDs) are sometimes not well understood. In particular, when the critical current is high, very irregular voltage versus flux characteristics can be measured. On the other hand, when the critical current is low, the characteristics follow perfectly the resistively shunted junction model. We have studied the dynamics of a dc-SQUID in the presence of stray capacitance and shunting resistors imbalance. The equations describing a circuit model for this physical system are integrated numerically and the results are compared with voltage versus flux characteristics obtained from fabricated devices. We find that the theoretical analysis accounts very well for previously misunderstood experimental features of the dc-SQUID. This model can give more physical sense to the various regimes of behavior of the dc-SQUID giving more insight into the experimental results.
We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.
The LC\mathrm{LC}LC (inductance-capacitance) resonance phenomenon in the dc SQUID (superconducting quantum interference device) creates a current peak in the $I\ensuremath{-}V$ characteristics at a voltage determined by the resonance frequency. These $I\ensuremath{-}V$ characteristics have been analyzed with the resistively shunted Josephson-junction model in the low-damping and small-oscillation regime. The resonance $I\ensuremath{-}V$ characteristics contain sufficient information to determine all circuit parameters for the dc SQUID's. Specifically, we can apply this analysis to symmetric, tunnel-junction dc SQUID's to deduce the pair-quasiparticle interference conductance ($cos\ensuremath{\theta}$ term).
Practical thin-film dc superconducting quantum interference devices (SQUIDs) are often built with an integrated input coil which leads to the formation of various parasitic elements. We have designed and fabricated several square washer-shaped dc SQUID test devices with various amounts of parasitic capacitance formed by covering the washer slits with superconducting coverplates of various widths. In the simplest approximation, the parasitic capacitance Cp appears entirely across the Josephson junctions; in a better approximation, Cp divides the total inductance into two parts, an effective SQUID loop inductance L and a small parasitic inductance Lp. For both models, noise-free and noise-rounded current-voltage and voltage-flux characteristics are calculated for various values of the ratios L/Lp and Cp/C, where C is the Josephson junction capacitance. The SQUID dynamics are significantly affected by Cp and Lp. The energy resolution ε at first deteriorates with increasing Cp for Cp/C ≲ 2, but as Cp/C becomes large, ε improves to less than twice the value for Cp/C ≊ 0. The optimal points of operation for large Cp, however, are found at voltages above the low-frequency resonance determined by L and Cp where the flux-to-voltage transfer function is low. Furthermore, for devices with Cp/C ≫ 1 and Lp≠0, the double-loop geometry leads to an additional resonance determined by Lp and C that appears at high frequencies. The energy resolution inside this high-frequency resonance is nearly independent of Cp and comparable to the energy resolution of a device having the same total inductance but with Cp/C ≪ 1. Extensive noise mappings on several different test devices have been carried out using a computer-controlled measurement system. The measured characteristics and noise performance are shown to be in good agreement with the simulations.
Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance Cs{C}_{s}Cs​ and resistance Rs{R}_{s}Rs​ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.
Noise characteristics of dc SQUIDs in large β regimes have been studied experimentally in the case when a SQUID inductance is resistively shunted. Here, β=2L I 0/Φ0 is the modulation parameter, L is the SQUID inductance, I 0 is the critical current of the Josephson junction and Φ0 is the flux quantum. It is shown experimentally that the performance of the SQUID does not degrade significantly even for large β values; for example, the minimum energy resolution of the SQUID is as small as ε=25h and the flux region where ε<50h is as wide as 0.1Φ0, even for the case β=12, where h is the Planck constant. The experimental results agree quantitatively with the theoretical ones.
Partly resistive superconducting quantum interference devices (RSQUIDs) are used in noise thermometry in the liquid helium temperature range. Here we analyze one type of RSQUID that has not been thoroughly investigated until now: the direct current biased with two Josephson junctions and a resistive part connected in series with the junctions and closed by a superconducting ring. The resistive shunted model of the Josephson junctions is used for the analysis. Two cases of the RSQUID ring inductance were analyzed: (i) negligibly small and (ii) small but finite inductance. The expressions for the low frequency output signal, the current–voltage (I–V) characteristics, and the current flowing through the resistive part are obtained. In the dependence of the output frequency versus the dc current passed through the resistive part often an offset is observed experimentally. This phenomenon can be explained as an influence of an asymmetry in the critical currents of the junctions.