The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.
The flux modulation scheme (FMS) is the standard readout technique of dc SQUIDs, where a step-up transformer links the SQUID to the preamplifier. The transformer's primary winding shunts the SQUID via a large capacitor while the secondary winding connects it to the preamplifier. A modulation flux having a frequency of typically 100 kHz generates an ac voltage across the SQUID, stepped up by the transformer. The SQUID with FMS is customarily operated in the current bias mode, because a constant dc bias current flows only through the SQUID due to the capacitor isolation. With FMS, however, the transformer ac shunts the SQUID so that in reality the operating mode is neither purely current-biased nor voltage-biased but rather nominal current-biased or “mixed biased.” Our objective is to experimentally investigate the consequences of ac shunting of the dc SQUID in FMS and the transformer's transfer characteristics. For different shunt values we measure the change in the SQUID bias current due to the ac shunt using another SQUID in the two-stage readout scheme, and simultaneously monitor the SQUID output voltage signal. We then explain our measurements by a simplified graphic analysis of SQUID intrinsic current-voltage (I–V) characteristics. Since the total current flowing through the SQUID is not constant due to the shunting effect of the transformer, the amplitude of SQUID flux-to-voltage characteristics V(Φ) is less as compared to the direct readout scheme (DRS). Furthermore, we analyze and compare V(Φ) obtained by DRS and FMS. We show that in FMS, the transfer characteristics of the SQUID circuit also depend on the isolation capacitance and the dynamic resistance of the SQUID.
Noise matching between superconducting quantum interference device (SQUID) sensor and readout electronics has always been an important problem. Conventionally, in order to avoid the hysteresis, SQUIDs should be operated in the range of βccis the Stewart-McCumber parameter. Recently, Liu et al. extended the SQUID operating area to βc > 1 due to a large noise parameter Γ*. When βc> 1, SQUID exhibits a large ∂V/∂Φ, which is beneficial in reducing the noise contribution of the readout electronics, δΦe. In this work, we compare the SQUID system noise δΦsmeasured with four different readout electronics. Here, the four readout electronics employed are as follows: 1) the flux modulation scheme (FMS); 2) the direct readout scheme (DRS), which uses six parallel connected bipolar transistor as its preamplifier (DRS-PCBT); 3) the DRS, which uses a single preamplifier AD797 (DRS-AD797); and 4) the two-stage scheme. The preamplifier voltage noise of DRS-PCBT and DRS-AD797 are about 0.4 nV/√Hz and 0.9 nV/√Hz, respectively. For a two-stage scheme, the equivalent flux noise reaches about 0.25 μΦ0/√Hz, the measured SQUID intrinsic noise, δΦi, will dominate δΦs. In other readout schemes, however, δΦsdepends on the value of βc. Finally, we found that FMS is suitable to match SQUIDs with βccc> 3.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
We present a MHz frequency-division direct-current superconducting quantum interference device (dc-SQUID) multiplexer that is based on flux ramp modulation and a series array of N identical current-sensing dc-SQUIDs with tightly coupled input coil. By running a periodic, sawtooth-shaped current signal through additional modulation coils being tightly but non-uniformly coupled to the individual SQUIDs, the voltage drop across the array changes according to the sum of the flux-to-voltage characteristics of the individual SQUIDs within each cycle of the modulation signal. In this mode of operation, an input signal injected in the input coil of one of the SQUIDs and being quasi-static within a time frame adds a constant flux offset and leads to a phase shift of the associated SQUID characteristics. The latter is proportional to the input signal and can be inferred by channelizing and down-converting the sampled array output voltage. Using a prototype multiplexer as well as custom readout electronics, we demonstrate the simultaneous readout of four signal sources with MHz bandwidth per channel.
We present a MHz frequency-division direct-current superconducting quantum interference device (dc-SQUID) multiplexer that is based on flux ramp modulation and a series array of N identical current-sensing dc-SQUIDs with tightly coupled input coil. By running a periodic, sawtooth-shaped current signal through additional modulation coils being tightly but non-uniformly coupled to the individual SQUIDs, the voltage drop across the array changes according to the sum of the flux-to-voltage characteristics of the individual SQUIDs within each cycle of the modulation signal. In this mode of operation, an input signal injected in the input coil of one of the SQUIDs and being quasi-static within a time frame adds a constant flux offset and leads to a phase shift of the associated SQUID characteristics. The latter is proportional to the input signal and can be inferred by channelizing and down-converting the sampled array output voltage. Using a prototype multiplexer as well as custom readout electronics, we demonstrate the simultaneous readout of four signal sources with MHz bandwidth per channel.
We present a novel dc-SQUID readout scheme that provides linearization of the relation between the input and output signal without using a conventional flux-locked loop circuit. It relies on applying a periodic, sawtooth-shaped magnetic flux signal to the modulation coil of the SQUID to continuously measure the flux-to-voltage SQUID characteristic within each period of the flux ramp. In case that the amplitude and repetition rate of the ramp are chosen such that multiple flux quanta are induced in the SQUID and that the input signal is quasistatic within one period of the flux ramp, the input signal adds a constant magnetic flux offset to the SQUID that leads to a phase shift of the SQUID characteristic being proportional to the input signal. We show that this scheme allows for significantly increasing the dynamic range and that it intrinsically allows for MHz frequency-division SQUID multiplexing.
Dependence of SQUID Intrinsic Flux Noise on Stewart–McCumber Parameter βc of Josephson Junction
It is known that three superconducting quantum interference device (SQUID) parameters, namely, the intrinsic flux noise δΦs, the flux-to-voltage transfer coefficient ∂V/∂Φ, and the dynamic resistance Rd, increase with increasing the Stewart- McCumber parameter βcof Josephson junction. It is very difficult to obtain the low values of δΦsfor a strongly damped SQUID due to its small ∂V/∂Φ. In this paper, we employ a two-stage scheme (TSS) to measure δΦsdirectly. Here, we use single chip readout electronics and a weakly damped SQUID with a βcof flux noise of the readout-SQUID system is about 4.8 μΦ0/√Hz 1.2, both acting as a readout-SQUID system (a preamplifier). The with a corner frequency of about 10 Hz. The front-end SQUID is coupled to the readout SQUID via the input coil with a mutual inductance of Mi. In our experiment, the flux gain for a readout SQUID, i.e., GΦ= Mi× (∂I/∂Φ)front-endis adjusted to be 20. Using the TSS, we measured δΦswith different βcchanging from 0.3 to 13.5 and found δΦsincreasing from 1.0 to 5.0 μΦ0/√Hz. We also discussed the relations between Ls, βc, and δΦsquantitatively. Finally, we proposed designing a suitable βcto match the preamplifier in a direct readout scheme to simplify a SQUID measurement system.