Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Bias conditions of dc-SQUID for a time-domain SQUID multiplexer

J. Beyer, D. Drung, K. D. Irwin

Published Jan 26, 2004• 4 citations
Publisher

Abstract

We have analyzed the biasing of the first-stage dc superconducting quantum interference devices (SQUIDs) of a time-domain dc-SQUID multiplexer (SQUID MUX) and find that the bias conditions of first-stage SQUIDs significantly affect the performance of the SQUID MUX in terms of total multiplexer noise and bandwidth. We present an experimental study of the operational parameters of a first-stage SQUID under varied bias conditions. Our measurements include a direct determination of the first-stage SQUID dynamic resistance RDYN1 and the flux noise of the first-stage SQUID biased over the range from voltage bias to current bias. Our measurements show that matching the bias resistors RS1 of the first-stage SQUIDs to RDYN1 improves the SQUID MUX noise performance as well as the first-stage bandwidth.

DOI
10.1063/1.1638877

Related papers

Performance of dc SQUIDs with resistively shunted inductance

Vittorio Foglietti, W. J. Gallagher, M. B. Ketchen +3 more

We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.

Applied Physics Letters•Oct 2, 1989•45 citations

Noise limits for dc SQUID readout of high-Q resonators below 300 MHz

Victoria Ankel, C. Bartram, J. Begin +38 more

We present the limits on noise for the readout of cryogenic high-Q resonators using dc Superconducting Quantum Interference Devices (SQUIDs) below 300 MHz. This analysis uses realized first-stage SQUIDs (previously published), whose performance is well described by Tesche–Clarke (TC) theory, coupled directly to the resonators. We also present data from a prototype second-stage dc SQUID array designed to couple to this first-stage SQUID as a follow-on amplifier with high system bandwidth. This analysis is the first full consideration of dc SQUID noise performance referred to a high-Q resonator over this frequency range and is presented relative to the standard quantum limit. We include imprecision, backaction, and backaction–imprecision noise correlations from TC theory, the noise contributed by the second-stage SQUIDs, wiring, and preamplifiers, and optimizations for both on-resonance measurements and off-resonance scan sensitivity. This architecture has modern relevance due to the increased interest in axion searches and the requirements of the DMRadio-m3 axion search, which uses dc SQUIDs in this frequency range.

arXiv:2504.20398•Journal of Applied Physics•Sep 4, 2025•0 citations

Origin of 1/f noise in Y1Ba2Cu3O7−x step-edge dc SQUIDs

Dirk Grundler, Rainer Eckart, Bernd R. David +1 more

We have fabricated Y1Ba2Cu3O7−x step-edge junction dc superconducting quantum interference devices (SQUIDs) and characterized their noise performance. The current-voltage characteristics of our SQUIDs are of resistively shunted junction type with critical current densities jc of about 104 A/cm2 and maximum flux to voltage transfer functions δV/δΦ of 20 μV/Φ0 at 77 K. We compare model predictions for 1/f noise in dc SQUIDs with experimental data and show that the frequency dependent noise in our devices results from critical current fluctuations of the Josephson junctions. A bias current reversing technique is effective in suppressing this noise contribution. A flux noise Φn of 80 μΦ0/Hz1/2 at 1 Hz and 77 K was measured on a dc SQUID with an inductance Ls of 60 pH.

Applied Physics Letters•Apr 26, 1993•24 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•72 citations

Improved dc SQUID read-out electronics with low 1/f noise preamplifier

D. Drung

An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.

Review of Scientific Instruments•Nov 1, 1997•43 citations

An insight into voltage-biased superconducting quantum interference devices

Chao Liu, Yi Zhang, Michael Mück +5 more

We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.

Applied Physics Letters•Nov 26, 2012•20 citations
We have analyzed the biasing of the first-stage dc superconducting quantum interference devices (SQUIDs) of a time-domain dc-SQUID multiplexer (SQUID MUX) and find that the bias conditions of first-stage SQUIDs significantly affect the performance of the SQUID MUX in terms of total multiplexer noise and bandwidth. We present an experimental study of the operational parameters of a first-stage SQUID under varied bias conditions. Our measurements include a direct determination of the first-stage SQUID dynamic resistance RDYN1 and the flux noise of the first-stage SQUID biased over the range from voltage bias to current bias. Our measurements show that matching the bias resistors RS1 of the first-stage SQUIDs to RDYN1 improves the SQUID MUX noise performance as well as the first-stage bandwidth.
We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.
We present the limits on noise for the readout of cryogenic high-Q resonators using dc Superconducting Quantum Interference Devices (SQUIDs) below 300 MHz. This analysis uses realized first-stage SQUIDs (previously published), whose performance is well described by Tesche–Clarke (TC) theory, coupled directly to the resonators. We also present data from a prototype second-stage dc SQUID array designed to couple to this first-stage SQUID as a follow-on amplifier with high system bandwidth. This analysis is the first full consideration of dc SQUID noise performance referred to a high-Q resonator over this frequency range and is presented relative to the standard quantum limit. We include imprecision, backaction, and backaction–imprecision noise correlations from TC theory, the noise contributed by the second-stage SQUIDs, wiring, and preamplifiers, and optimizations for both on-resonance measurements and off-resonance scan sensitivity. This architecture has modern relevance due to the increased interest in axion searches and the requirements of the DMRadio-m3 axion search, which uses dc SQUIDs in this frequency range.
We have fabricated Y1Ba2Cu3O7−x step-edge junction dc superconducting quantum interference devices (SQUIDs) and characterized their noise performance. The current-voltage characteristics of our SQUIDs are of resistively shunted junction type with critical current densities jc of about 104 A/cm2 and maximum flux to voltage transfer functions δV/δΦ of 20 μV/Φ0 at 77 K. We compare model predictions for 1/f noise in dc SQUIDs with experimental data and show that the frequency dependent noise in our devices results from critical current fluctuations of the Josephson junctions. A bias current reversing technique is effective in suppressing this noise contribution. A flux noise Φn of 80 μΦ0/Hz1/2 at 1 Hz and 77 K was measured on a dc SQUID with an inductance Ls of 60 pH.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.
We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.