Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Gain Bandwidth and Noise Temperature of NbTiN HEB Mixer

Gregory N Gol'tsman, Matvey I. Finkel, Yu. B. Vachtomin, Sergey V. Antipov, Vladimir Drakinski, N. Kaurova, Boris M. Voronov

Published Apr 1, 2003• 4 citations
OpenAlex

Related papers

1.5 THz heterodyne receiver with waveguide superconducting NbTiN hot electron bolometer mixer

Ling Jiang, T. Shiino, Sukeyasu Steven Yamamoto +2 more

In this paper, we present measured results and theoretical modeling of a 1.5 THz waveguide NbTiN HEB mixer, which is fabricated by in situ process. The NbTiN HEB mixer with dimensions of 1 μm in width and 0.15 μm in length is measured to be as low as 570 K in noise temperature (7hν/k) even with a relatively thick NbTiN film (10.8 nm). The intrinsic mixer noise temperature is 300 K after the correction of the losses of quasi-optical and IF amplifier chain. At the same time, we adopt an optimized hot spot model to simulate the DC and RF behaviors of the NbTiN HEB mixer by combining phonon-cooling and diffusion-cooling mechanisms together. The measured and calculated current-voltage curves are in good agreement. The calculated intrinsic mixer noise temperature is 100 K and IF gain bandwidth is 2.7 GHz at the optimum bias point. The difference between the measured and simulated mixer noise temperature is factor of 3 times, which is probably due to misalignment of quasi-optical RF coupling system and air loss. The calculated and measured results show the two cooling mechanism work together to lower the noise temperature of the waveguide NbTiN HEB mixers. The details will be presented in this paper.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 9, 2011•0 citations

Superconducting Integrated Receiver with HEB-Mixer

Nickolay V. Kinev, Lyudmila V. Filippenko, Roman V. Ozhegov +3 more

•Apr 27, 2014•0 citations

Developmental study on an NbTiN HEB mixer for astronomical applications

謙 新保

•Jan 1, 2008•1 citation

Intrinsic Mixing Behavior of Superconducting NbTiN HEB Mixer Based on in-situ Technique

Ling Jiang, T. Shiino, Sukeyasu Steven Yamamoto +1 more

In this paper, we present the intrinsic mixing behavior of superconducting niobium titanium nitride hot electron bolometer mixer based on in-situ technique. We make detailed comparison between simulated and measured performance of the HEB mixers at 0.8 and 1.5 THz. A distributed hot spot model which is based on solving a heat balance equation is employed to characterize current-voltage curve, electron and phonon temperature distribution along superconducting microbridge, intermediate frequency gain bandwidth and intrinsic noise temperature of the mixers. The simulated intermediate frequency gain bandwidth decreases with the increase of microbridge length, which is in good agreement with measured results. For the microbridge with 0.15 µm in length, the IF gain bandwidth is simulated to be 2.6 GHz at 0.8 and 1.5 THz. When the microbridge length is increased to 0.3 µm, the calculated IF gain bandwidth is 1.8 GHz. The simulated results demonstrate the IF gain bandwidth is only related with microbridge length, independent of RF frequency. It's very useful to find the critical parameters which mainly affects the mixer noise temperature and IF gain bandwidth. In this paper we will give the critical factors as the reference for fabrication and measurement of HEB mixers. We have found that when the ratio of length to width of the microbridge is set to be around 0.15, the simulated and measured mixer noise temperature show the lowest value. More details will be presented in the paper.

•Jan 1, 2012•0 citations

Development of 1.5 THz waveguide NbTiN superconducting hot electron bolometer mixers

Ling Jiang, Shoichi Shiba, Tatsuya Shiino +7 more

We present a characterization of a 1.5 THz waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixer which can be pumped by a commercial solid state tunable local oscillator (LO) source. The NbTiN HEB mixer is made from a 12 nm thick NbTiN thin film deposited on a quartz substrate at room temperature. A gold electrode is formed in situ on the NbTiN thin film without breaking vacuum to ensure good contact. The uncorrected DSB receiver noise temperature is measured to be 1700 K at 1.5 THz, whereas the mixer noise temperature is derived to be 1000 K after corrections for losses of the input optics and the intermediate frequency (IF) amplifier chain. The required LO power absorbed in the HEB mixer is evaluated to be 340 nW by using an isothermal technique. The IF gain bandwidth is supposed to be about 1.3 GHz or higher. The present results show that good performance can be obtained at 1.5 THz even with a relatively thick NbTiN film (12 nm), as in the case of 0.8 THz. In order to investigate the cooling mechanism of our HEB mixers, we have conducted performance measurements for a few HEB mixers with different microbridge sizes both at 1.5 and 0.8 THz. The noise performance of the NbTiN HEB mixers is found to depend on the length of the NbTiN microbridge. The shorter the microbridge is, the lower the receiver noise temperature is. This may imply a contribution of the diffusion cooling in addition to the phonon cooling.

Superconductor Science and Technology•Mar 19, 2010•21 citations

Design and fabrication of superconducting HEB mixer

Jinping Wang, YangBin Li, Lin Kang +7 more

中国科学通报:英文版•Jun 1, 2009•7 citations
In this paper, we present measured results and theoretical modeling of a 1.5 THz waveguide NbTiN HEB mixer, which is fabricated by in situ process. The NbTiN HEB mixer with dimensions of 1 μm in width and 0.15 μm in length is measured to be as low as 570 K in noise temperature (7hν/k) even with a relatively thick NbTiN film (10.8 nm). The intrinsic mixer noise temperature is 300 K after the correction of the losses of quasi-optical and IF amplifier chain. At the same time, we adopt an optimized hot spot model to simulate the DC and RF behaviors of the NbTiN HEB mixer by combining phonon-cooling and diffusion-cooling mechanisms together. The measured and calculated current-voltage curves are in good agreement. The calculated intrinsic mixer noise temperature is 100 K and IF gain bandwidth is 2.7 GHz at the optimum bias point. The difference between the measured and simulated mixer noise temperature is factor of 3 times, which is probably due to misalignment of quasi-optical RF coupling system and air loss. The calculated and measured results show the two cooling mechanism work together to lower the noise temperature of the waveguide NbTiN HEB mixers. The details will be presented in this paper.
In this paper, we present the intrinsic mixing behavior of superconducting niobium titanium nitride hot electron bolometer mixer based on in-situ technique. We make detailed comparison between simulated and measured performance of the HEB mixers at 0.8 and 1.5 THz. A distributed hot spot model which is based on solving a heat balance equation is employed to characterize current-voltage curve, electron and phonon temperature distribution along superconducting microbridge, intermediate frequency gain bandwidth and intrinsic noise temperature of the mixers. The simulated intermediate frequency gain bandwidth decreases with the increase of microbridge length, which is in good agreement with measured results. For the microbridge with 0.15 µm in length, the IF gain bandwidth is simulated to be 2.6 GHz at 0.8 and 1.5 THz. When the microbridge length is increased to 0.3 µm, the calculated IF gain bandwidth is 1.8 GHz. The simulated results demonstrate the IF gain bandwidth is only related with microbridge length, independent of RF frequency. It's very useful to find the critical parameters which mainly affects the mixer noise temperature and IF gain bandwidth. In this paper we will give the critical factors as the reference for fabrication and measurement of HEB mixers. We have found that when the ratio of length to width of the microbridge is set to be around 0.15, the simulated and measured mixer noise temperature show the lowest value. More details will be presented in the paper.
We present a characterization of a 1.5 THz waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixer which can be pumped by a commercial solid state tunable local oscillator (LO) source. The NbTiN HEB mixer is made from a 12 nm thick NbTiN thin film deposited on a quartz substrate at room temperature. A gold electrode is formed in situ on the NbTiN thin film without breaking vacuum to ensure good contact. The uncorrected DSB receiver noise temperature is measured to be 1700 K at 1.5 THz, whereas the mixer noise temperature is derived to be 1000 K after corrections for losses of the input optics and the intermediate frequency (IF) amplifier chain. The required LO power absorbed in the HEB mixer is evaluated to be 340 nW by using an isothermal technique. The IF gain bandwidth is supposed to be about 1.3 GHz or higher. The present results show that good performance can be obtained at 1.5 THz even with a relatively thick NbTiN film (12 nm), as in the case of 0.8 THz. In order to investigate the cooling mechanism of our HEB mixers, we have conducted performance measurements for a few HEB mixers with different microbridge sizes both at 1.5 and 0.8 THz. The noise performance of the NbTiN HEB mixers is found to depend on the length of the NbTiN microbridge. The shorter the microbridge is, the lower the receiver noise temperature is. This may imply a contribution of the diffusion cooling in addition to the phonon cooling.