Intrinsic Mixing Behavior of Superconducting NbTiN HEB Mixer Based on in-situ Technique

Ling Jiang, T. Shiino, Sukeyasu Steven Yamamoto, Y. F. Liu

Published Jan 1, 2012• 0 citations

Abstract

In this paper, we present the intrinsic mixing behavior of superconducting niobium titanium nitride hot electron bolometer mixer based on in-situ technique. We make detailed comparison between simulated and measured performance of the HEB mixers at 0.8 and 1.5 THz. A distributed hot spot model which is based on solving a heat balance equation is employed to characterize current-voltage curve, electron and phonon temperature distribution along superconducting microbridge, intermediate frequency gain bandwidth and intrinsic noise temperature of the mixers. The simulated intermediate frequency gain bandwidth decreases with the increase of microbridge length, which is in good agreement with measured results. For the microbridge with 0.15 µm in length, the IF gain bandwidth is simulated to be 2.6 GHz at 0.8 and 1.5 THz. When the microbridge length is increased to 0.3 µm, the calculated IF gain bandwidth is 1.8 GHz. The simulated results demonstrate the IF gain bandwidth is only related with microbridge length, independent of RF frequency. It's very useful to find the critical parameters which mainly affects the mixer noise temperature and IF gain bandwidth. In this paper we will give the critical factors as the reference for fabrication and measurement of HEB mixers. We have found that when the ratio of length to width of the microbridge is set to be around 0.15, the simulated and measured mixer noise temperature show the lowest value. More details will be presented in the paper.

Related papers

Modeling and measurement of IF gain bandwidth and intrinsic noise temperature for NbTiN hot electron bolometer mixers at Terahertz frequencies

Ling Jiang, Fei Liu Yun, Satoshi Yamamoto

In this paper, we present the modeling and measurement results of niobium titanium nitride hot electron bolometer mixers with different sizes at terahertz frequencies. A distributed hot spot model which is based on solving a heat balance equation is employed to characterize current-voltage curve, electron and phonon temperature distribution along superconducting microbridge, intermediate frequency gain bandwidth and intrinsic noise temperature of the mixers. The simulated intermediate frequency gain bandwidth decreases with the increase of microbridge length, which is in good agreement with measured results. A difference of factor of several tens exists between the calculated and measured mixer noise temperature, which is probably due to the disfigurement of waveguide structure and unknown noise from the mixer.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIENov 3, 20100 citations

1.5 THz heterodyne receiver with waveguide superconducting NbTiN hot electron bolometer mixer

Ling Jiang, T. Shiino, Sukeyasu Steven Yamamoto +2 more

In this paper, we present measured results and theoretical modeling of a 1.5 THz waveguide NbTiN HEB mixer, which is fabricated by in situ process. The NbTiN HEB mixer with dimensions of 1 μm in width and 0.15 μm in length is measured to be as low as 570 K in noise temperature (7hν/k) even with a relatively thick NbTiN film (10.8 nm). The intrinsic mixer noise temperature is 300 K after the correction of the losses of quasi-optical and IF amplifier chain. At the same time, we adopt an optimized hot spot model to simulate the DC and RF behaviors of the NbTiN HEB mixer by combining phonon-cooling and diffusion-cooling mechanisms together. The measured and calculated current-voltage curves are in good agreement. The calculated intrinsic mixer noise temperature is 100 K and IF gain bandwidth is 2.7 GHz at the optimum bias point. The difference between the measured and simulated mixer noise temperature is factor of 3 times, which is probably due to misalignment of quasi-optical RF coupling system and air loss. The calculated and measured results show the two cooling mechanism work together to lower the noise temperature of the waveguide NbTiN HEB mixers. The details will be presented in this paper.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIEJun 9, 20110 citations

Development of 1.5 THz waveguide NbTiN superconducting hot electron bolometer mixers

Ling Jiang, Shoichi Shiba, Tatsuya Shiino +7 more

We present a characterization of a 1.5 THz waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixer which can be pumped by a commercial solid state tunable local oscillator (LO) source. The NbTiN HEB mixer is made from a 12 nm thick NbTiN thin film deposited on a quartz substrate at room temperature. A gold electrode is formed in situ on the NbTiN thin film without breaking vacuum to ensure good contact. The uncorrected DSB receiver noise temperature is measured to be 1700 K at 1.5 THz, whereas the mixer noise temperature is derived to be 1000 K after corrections for losses of the input optics and the intermediate frequency (IF) amplifier chain. The required LO power absorbed in the HEB mixer is evaluated to be 340 nW by using an isothermal technique. The IF gain bandwidth is supposed to be about 1.3 GHz or higher. The present results show that good performance can be obtained at 1.5 THz even with a relatively thick NbTiN film (12 nm), as in the case of 0.8 THz. In order to investigate the cooling mechanism of our HEB mixers, we have conducted performance measurements for a few HEB mixers with different microbridge sizes both at 1.5 and 0.8 THz. The noise performance of the NbTiN HEB mixers is found to depend on the length of the NbTiN microbridge. The shorter the microbridge is, the lower the receiver noise temperature is. This may imply a contribution of the diffusion cooling in addition to the phonon cooling.

Superconductor Science and TechnologyMar 19, 201020 citations

Investigation of the Performance of NbN Superconducting HEB Mixers of Different Critical Temperatures

Wei Miao, Wen Zhang, Kangmin Zhou +7 more

In this paper, we investigate the critical temperature dependence of the performance of niobium nitride superconducting hot electron bolometer (HEB) mixers. The input noise temperature and intermediate frequency (IF) noise bandwidth of superconducting HEB mixers of different critical temperatures Tc(between 6 and 12 K) are simulated with a hot spot model. Simulation results show that the mixer input noise temperature is the lowest at Tcapproximately equal to 7-9.5 K and the IF noise bandwidth increases with Tc. We also measure three superconducting HEB mixers of different critical temperatures (i.e., 7.5, 8.8, and 10.3 K) at 0.85 and 1.3 THz. An agreement between measurement and prediction is observed.

IEEE Transactions on Applied SuperconductivityNov 21, 20168 citations

Stability of a Quasi-Optical Superconducting NbTiN Hot-Electron Bolometer Mixer at 1.5 THz Frequency Band

Hiroyuki Maezawa, T. Yamakura, T. Shiino +10 more

We are developing quasi-optical superconducting hot-electron bolometer (HEB) mixer receivers for astronomical and atmospheric remote sensing applications. The microbridge of the HEB mixer was fabricated at room temperature from a 6.8-nm-thick niobium titanium nitride (NbTiN) film deposited on a 20-nm-thick aluminum nitride (AlN) buffer layer, using a helicon sputtering technique at a slow deposition rate. The mixer was cooled to 4.2 K using a closed-cycled mechanical 4 K pulse-tube cryocooler with a temperature fluctuation of$\pm$1.6 mK. The stability of a large-volume NbTiN HEB mixer was studied at 1.47 THz by changing local oscillator (LO) power with the mixer bias voltage fixed. The intermediate frequency (IF) signal measured at 1.5 GHz had a maximum peak at a certain mixer bias current. The receiver noise temperature was lowest at around the IF maximum peak. It was also found that the IF signal was most stable at around the IF maximum peak under conditions in which the instability of LO pumping level, induced by small mechanical vibrations of the cryostat, remained in the optical system.

IEEE Transactions on Applied SuperconductivityJan 24, 20116 citations

Development of THz Waveguide NbTiN HEB Mixers

Ling Jiang, S. Shiba, K. Shimbo +7 more

In this paper, we present the development of the waveguide niobium titanium nitride (NbTiN) superconducting hot electron bolometer (HEB) mixers, cryogenically cooled by a 4 K close-cycled refrigerator. The NbTiN thin film is formed on a crystalline quartz substrate by sputtering an NbTi target with the Ar and N2gas at room temperature. The HEB mixer element is fabricated by using the 12 nm NbTiN film, and is mounted on a waveguide block. Measurement of a Fourier transform spectrometer shows that the response of the mixer is centered near 810 GHz with a bandwidth of about 500 GHz. The uncorrected DSB receiver noise temperature is measured to be 500 K, and the noise bandwidth is to be 1.4 GHz at 810 GHz. The present result shows that a good noise performance can be obtained for the NbTiN HEB mixer even with a relatively thick film (12 nm) fabricated at the room temperature.

IEEE Transactions on Applied SuperconductivityJun 1, 200916 citations