Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Demonstration of Microwave Multiplexed Readout of DC-Biased Superconducting Nanowire Detectors

Sinclair, AK, Schroeder, E, Di Zhu, Marco Colangelo, Glasby, J, Mauskopf, PD, Mani, H, Berggren, KK

Published Jan 1, 2019• 14 citations
OpenAlex

Abstract

© 2002-2011 IEEE. Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.

Related papers

Demonstration of Microwave Multiplexed Readout of DC-Biased Superconducting Nanowire Detectors

A. K. Sinclair, E. Schroeder, Di Zhu +5 more

Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.

arXiv:1905.06880•IEEE Transactions on Applied Superconductivity•Mar 8, 2019•26 citations

Frequency-multiplexed bias and readout of a 16-pixel superconducting nanowire single-photon detector array

S. Doerner, A. Kuzmin, S. Wünsch +4 more

We demonstrate a 16-pixel array of microwave-current driven superconducting nanowire single-photon detectors with an integrated and scalable frequency-division multiplexing architecture, which reduces the required number of bias and readout lines to a single microwave feed line. The electrical behavior of the photon-sensitive nanowires, embedded in a resonant circuit, as well as the optical performance and timing jitter of the single detectors is discussed. Besides the single pixel measurements, we also demonstrate the operation of a 16-pixel array with a temporal, spatial, and photon-number resolution.

arXiv:1705.05345•Applied Physics Letters•Jul 17, 2017•88 citations

Operation of Superconducting Nanowire Single-Photon Detectors Embedded in Lumped-Element Resonant Circuits

Steffen Doerner, Artem A. Kuzmin, S. Wünsch +2 more

We propose a new operation principle for superconducting nanowire single-photon detectors (SNSPDs) enabling an efficient frequency-division multiplexing of the bias and readout signals of a large multipixel detector array. The SNSPD is part of a resonant circuit, and the microwave signal inside the device is used to bias the detector close to the critical state. Hence, an n×m pixel SNSPD array requires only two coaxial cables from room temperature to the detector ambient temperature of 4.2 K. We show the microwave characterization and single-photon response of such devices and compare the detector efficiencies with conventional dc-biased SNSPDs. Furthermore, we demonstrate the feasibility of array applications with the new operation mode in a two-pixel proof-of-principle device.

IEEE Transactions on Applied Superconductivity•Feb 5, 2016•19 citations

Time-Tagged Multiplexing of Serially Biased Superconducting Nanowire Single-Photon Detectors

M. Hofherr, Matthias Arndt, K. Ilin +5 more

We present a concept for a time-tagged multiplexed readout of several superconducting nanowire single-photon detector elements for small arrays in ultra-short pulsed laser applications. The detector elements were coupled in an array by a superconducting delay line giving each detector element a temporal signature. The complete detector chain is biased by one bias supply. The patterning concept and the first experimental proof of principle are demonstrated on two-detector element arrays with delay times of 86 and 156 ps each made from a 5-nm NbN film on sapphire. We discuss the propagation delay of a delay line taking the geometric and kinetic inductance into account. We show that mainly the normal conducting propagation velocity defines the characteristic time of the delay line and that the inductance dependent response pulse width currently limits the maximum number of detector elements.

IEEE Transactions on Applied Superconductivity•Feb 11, 2013•44 citations

Superconducting nanowire single photon detector under AC-bias with self-differential readout

Luyao Ma, Xing-Yu Zhang, Zhi-Yun Shu +4 more

Superconducting nanowire single photon detector (SNSPD) has been widely used in many fields such as quantum computing, quantum key distribution and laser radar, due to its high detection efficiency, low dark count rate, high counting rate, and low timing jitter. In most cases, the SNSPD works under the DC-bias mode that can detect single photons arrived at any time. In some cases such as satellite laser ranging and single-photon laser radar where the light pulses arrive regularly, the AC-bias mode enables the SNSPD to work with higher counting rates and lower background dark counts, which however requires complicated readout due to the low signal-to-noise ratio of the photon response. In this work, we report on an AC-biased SNSPD system with a self-differential readout circuit. The system includes a 2-pixel SNSPD consisting of two parallel nanowires, which are biased with 100 MHz sinusoidal current. The output signals of these two nanowires are amplified and combined for the differential readout of the photon response. The resulting response pulse possesses a signal-to-noise ratio ten times higher than that extracted before self-differential readout. In addition, the dark counts are reduced by a factor of 4, and the count rates are increased by a factor of 1.5, in comparison with those under the DC-bias mode. This work provides a specific method to read out the AC-biased SNSPD.

Acta Physica Sinica•Jan 1, 2022•4 citations

Characterize the switching performance of a superconducting nanowire cryotron for reading superconducting nanowire single photon detectors

Kai Zheng, Qingyuan Zhao, Ling-Dong Kong +8 more

Scalable superconducting nanowire single photon detector (SNSPDs) arrays require cryogenic digital circuits for multiplexing the output detection pulses. Among existing superconducting digital devices, superconducting nanowire cryotron (nTron) is a three-terminal device with an ultra-compact size, which is promising for large scale monolithic integration. In this report, in order to evaluate the potential and possibility of using nTrons for reading and digitizing SNSPD signals, we characterized the grey zone, speed, timing jitter and power dissipation of a proper designed nTron. With a DC bias on the gate, the nTron can be triggered by a few μA high and nanoseconds wide input signal, showing the nTron was capable of reading an SNSPD pulse at the same signal level. The timing jitter depended on the input signal level. For a 20 μA high and 5 ns wide input pulse, the timing jitter was 33.3 ps, while a typical SNSPD's jitter was around 50 ps. With removing the serial inductors and operating it in an AC bias mode. The nTron was demonstrated to be operated at a clock frequency of 615.4 MHz, which was faster than the maximum counting rate of a typical SNSPD. In additional, with a 50 Ω bias resistor and biased at 17.6 μA, the nTron had a total power dissipation of 19.7 nW. Although RSFQ circuits are faster than nTrons, for reading SNSPD or other detector arrays that demands less operation speed, our results suggest a digital circuit made from nTrons could be another promising alternative.

Scientific Reports•Nov 8, 2019•17 citations
© 2002-2011 IEEE. Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.
Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.
We demonstrate a 16-pixel array of microwave-current driven superconducting nanowire single-photon detectors with an integrated and scalable frequency-division multiplexing architecture, which reduces the required number of bias and readout lines to a single microwave feed line. The electrical behavior of the photon-sensitive nanowires, embedded in a resonant circuit, as well as the optical performance and timing jitter of the single detectors is discussed. Besides the single pixel measurements, we also demonstrate the operation of a 16-pixel array with a temporal, spatial, and photon-number resolution.
We propose a new operation principle for superconducting nanowire single-photon detectors (SNSPDs) enabling an efficient frequency-division multiplexing of the bias and readout signals of a large multipixel detector array. The SNSPD is part of a resonant circuit, and the microwave signal inside the device is used to bias the detector close to the critical state. Hence, an n×m pixel SNSPD array requires only two coaxial cables from room temperature to the detector ambient temperature of 4.2 K. We show the microwave characterization and single-photon response of such devices and compare the detector efficiencies with conventional dc-biased SNSPDs. Furthermore, we demonstrate the feasibility of array applications with the new operation mode in a two-pixel proof-of-principle device.
We present a concept for a time-tagged multiplexed readout of several superconducting nanowire single-photon detector elements for small arrays in ultra-short pulsed laser applications. The detector elements were coupled in an array by a superconducting delay line giving each detector element a temporal signature. The complete detector chain is biased by one bias supply. The patterning concept and the first experimental proof of principle are demonstrated on two-detector element arrays with delay times of 86 and 156 ps each made from a 5-nm NbN film on sapphire. We discuss the propagation delay of a delay line taking the geometric and kinetic inductance into account. We show that mainly the normal conducting propagation velocity defines the characteristic time of the delay line and that the inductance dependent response pulse width currently limits the maximum number of detector elements.
Superconducting nanowire single photon detector (SNSPD) has been widely used in many fields such as quantum computing, quantum key distribution and laser radar, due to its high detection efficiency, low dark count rate, high counting rate, and low timing jitter. In most cases, the SNSPD works under the DC-bias mode that can detect single photons arrived at any time. In some cases such as satellite laser ranging and single-photon laser radar where the light pulses arrive regularly, the AC-bias mode enables the SNSPD to work with higher counting rates and lower background dark counts, which however requires complicated readout due to the low signal-to-noise ratio of the photon response. In this work, we report on an AC-biased SNSPD system with a self-differential readout circuit. The system includes a 2-pixel SNSPD consisting of two parallel nanowires, which are biased with 100 MHz sinusoidal current. The output signals of these two nanowires are amplified and combined for the differential readout of the photon response. The resulting response pulse possesses a signal-to-noise ratio ten times higher than that extracted before self-differential readout. In addition, the dark counts are reduced by a factor of 4, and the count rates are increased by a factor of 1.5, in comparison with those under the DC-bias mode. This work provides a specific method to read out the AC-biased SNSPD.
Scalable superconducting nanowire single photon detector (SNSPDs) arrays require cryogenic digital circuits for multiplexing the output detection pulses. Among existing superconducting digital devices, superconducting nanowire cryotron (nTron) is a three-terminal device with an ultra-compact size, which is promising for large scale monolithic integration. In this report, in order to evaluate the potential and possibility of using nTrons for reading and digitizing SNSPD signals, we characterized the grey zone, speed, timing jitter and power dissipation of a proper designed nTron. With a DC bias on the gate, the nTron can be triggered by a few μA high and nanoseconds wide input signal, showing the nTron was capable of reading an SNSPD pulse at the same signal level. The timing jitter depended on the input signal level. For a 20 μA high and 5 ns wide input pulse, the timing jitter was 33.3 ps, while a typical SNSPD's jitter was around 50 ps. With removing the serial inductors and operating it in an AC bias mode. The nTron was demonstrated to be operated at a clock frequency of 615.4 MHz, which was faster than the maximum counting rate of a typical SNSPD. In additional, with a 50 Ω bias resistor and biased at 17.6 μA, the nTron had a total power dissipation of 19.7 nW. Although RSFQ circuits are faster than nTrons, for reading SNSPD or other detector arrays that demands less operation speed, our results suggest a digital circuit made from nTrons could be another promising alternative.