Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Acta Physica Sinica

Superconducting nanowire single photon detector under AC-bias with self-differential readout

Luyao Ma, Xing-Yu Zhang, Zhi-Yun Shu, You Xiao, Tian-Zhu Zhang, Hao Li, Lixing You

Published Jan 1, 2022• 4 citations
Publisher

Abstract

Superconducting nanowire single photon detector (SNSPD) has been widely used in many fields such as quantum computing, quantum key distribution and laser radar, due to its high detection efficiency, low dark count rate, high counting rate, and low timing jitter. In most cases, the SNSPD works under the DC-bias mode that can detect single photons arrived at any time. In some cases such as satellite laser ranging and single-photon laser radar where the light pulses arrive regularly, the AC-bias mode enables the SNSPD to work with higher counting rates and lower background dark counts, which however requires complicated readout due to the low signal-to-noise ratio of the photon response. In this work, we report on an AC-biased SNSPD system with a self-differential readout circuit. The system includes a 2-pixel SNSPD consisting of two parallel nanowires, which are biased with 100 MHz sinusoidal current. The output signals of these two nanowires are amplified and combined for the differential readout of the photon response. The resulting response pulse possesses a signal-to-noise ratio ten times higher than that extracted before self-differential readout. In addition, the dark counts are reduced by a factor of 4, and the count rates are increased by a factor of 1.5, in comparison with those under the DC-bias mode. This work provides a specific method to read out the AC-biased SNSPD.

DOI
10.7498/aps.71.20220373

Related papers

Practical High-Efficiency SNSPD Balanced High Speed and Low Jitter on Filter Circuit

Changmin Li, Guangzhao Xu, Xingyu Zhang +7 more

Superconducting nanowire single-photon detectors (SNSPDs) are integral to the fields of quantum information and quantum communication, offering high efficiency, low dark count rate, high count rate, and minimal timing jitter. However, a common challenge with SNSPDs is their propensity for latching and nonlinear count rate increase under high incident photon fluxes due to the traditional external readout circuitry. This issue is primarily caused by large dynamic inductance and the ac-coupled effects of the bias and amplifier capacitors. In this study, we carefully selected a commercial SNSPD with an efficiency of over 95%. To address the aforementioned challenges, we implemented a resistor–inductor-type filter structure, which is directly coupled to a low-temperature amplifier, and their operating temperature is 40 K. Experimental results revealed that the enhanced SNSPD readout circuit achieves a count rate that is approximately 3.5 times greater than that of the traditional circuit. Moreover, the timing jitter of the SNSPD was optimized, decreasing by approximately 3.6 times under high incident photon fluxes. These performance enhancements could significantly improve high-speed optical communication and quantum precision measurement.

IEEE Transactions on Applied Superconductivity•Jul 15, 2024•3 citations

Enhancement of photon detection in superconducting nanowire single photon detector exposed to oscillating magnetic field

Ilan Hakimi, Naor Vardi, Amos Sharoni +2 more

We measured the photon count rate (PCR) and dark count rate (DCR) of a superconducting nanowire single photon detector (SNSPD) exposed to either a DC magnetic field (up to 60 mT) or to a low-amplitude oscillating field (0.12–0.48 mT, up to 50 kHz). In both cases, the results show an increase in the PCR and the DCR as the DC field or the frequency of the AC field increase. However, the ratio DCR/(PCR + DCR) increases significantly with an increasing DC field, whereas this ratio is approximately constant as the frequency of the AC field increases up to frequencies in the kHz regime. The results suggest a more favorable effect of AC fields on the operation of the SNSPD.

Applied Physics Letters•Jun 7, 2021•3 citations

SNSPD with parallel nanowires (Conference Presentation)

Mikkel Ejrnaes, L. Parlato, Alessandro Gaggero +4 more

Superconducting nanowire single-photon detectors (SNSPDs) have shown to be promising in applications such as quantum communication and computation, quantum optics, imaging, metrology and sensing. They offer the advantages of a low dark count rate, high efficiency, a broadband response, a short time jitter, a high repetition rate, and no need for gated-mode operation. Several SNSPD designs have been proposed in literature. Here, we discuss the so-called parallel nanowires configurations. They were introduced with the aim of improving some SNSPD property like detection efficiency, speed, signal-to-noise ratio, or photon number resolution. Although apparently similar, the various parallel designs are not the same. There is no one design that can improve the mentioned properties all together. In fact, each design presents its own characteristics with specific advantages and drawbacks. In this work, we will discuss the various designs outlining peculiarities and possible improvements.

•Jun 8, 2017•0 citations

Effect of temperature on superconducting nanowire single-photon detector noise

A. Bahgat Shehata, Alessandro Ruggeri, Franco Stellari +6 more

Today Superconducting Nanowire Single-Photon Detectors (SNSPDs) are commonly used in different photon-starved applications, including testing and diagnostics of VLSI circuits. Detecting very faint signals in the near-infrared wavelength range requires not only good detection efficiency, but also very low Dark Count Rate (DCR) and jitter. For example, low noise is crucial to enable ultra-low voltage optical testing of integrated circuits. The effect of detector temperature and background thermal radiation on the noise of superconducting single-photon detectors made of NbN meanders is studied in this paper. It is shown that two different regimes can be identified in the DCR vs. bias current characteristics. At high bias, the dark count rate is dominated by the intrinsic noise of the detector, while at low bias current it is dominated by the detection of stray photons that get onto the SNSPD. Changing the detector temperature changes its switching current and only affects the high bias branch of the characteristics: a reduction of the DCR can be achieved by lowering the SNSPD base temperature. On the other hand, changing the temperature of the single-photon light source (e.g. the VLSI circuit under test) only affects the low bias regime: a lower target temperature leads to a smaller DCR.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Aug 28, 2015•1 citation

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Jitter analysis of a superconducting nanowire single photon detector

Lixing You, Xiaoyan Yang, Yuhao He +9 more

Jitter is one of the key parameters for a superconducting nanowire single photon detector (SNSPD). Using an optimized time-correlated single photon counting system for jitter measurement, we extensively studied the dependence of system jitter on the bias current and working temperature. The signal-to-noise ratio of the single-photon-response pulse was proven to be an important factor in system jitter. The final system jitter was reduced to 18 ps by using a high-critical-current SNSPD, which showed an intrinsic SNSPD jitter of 15 ps. A laser ranging experiment using a 15-ps SNSPD achieved a record depth resolution of 3 mm at a wavelength of 1550 nm.

arXiv:1308.0763•AIP Advances•Jul 1, 2013•135 citations
Superconducting nanowire single photon detector (SNSPD) has been widely used in many fields such as quantum computing, quantum key distribution and laser radar, due to its high detection efficiency, low dark count rate, high counting rate, and low timing jitter. In most cases, the SNSPD works under the DC-bias mode that can detect single photons arrived at any time. In some cases such as satellite laser ranging and single-photon laser radar where the light pulses arrive regularly, the AC-bias mode enables the SNSPD to work with higher counting rates and lower background dark counts, which however requires complicated readout due to the low signal-to-noise ratio of the photon response. In this work, we report on an AC-biased SNSPD system with a self-differential readout circuit. The system includes a 2-pixel SNSPD consisting of two parallel nanowires, which are biased with 100 MHz sinusoidal current. The output signals of these two nanowires are amplified and combined for the differential readout of the photon response. The resulting response pulse possesses a signal-to-noise ratio ten times higher than that extracted before self-differential readout. In addition, the dark counts are reduced by a factor of 4, and the count rates are increased by a factor of 1.5, in comparison with those under the DC-bias mode. This work provides a specific method to read out the AC-biased SNSPD.
Superconducting nanowire single-photon detectors (SNSPDs) are integral to the fields of quantum information and quantum communication, offering high efficiency, low dark count rate, high count rate, and minimal timing jitter. However, a common challenge with SNSPDs is their propensity for latching and nonlinear count rate increase under high incident photon fluxes due to the traditional external readout circuitry. This issue is primarily caused by large dynamic inductance and the ac-coupled effects of the bias and amplifier capacitors. In this study, we carefully selected a commercial SNSPD with an efficiency of over 95%. To address the aforementioned challenges, we implemented a resistor–inductor-type filter structure, which is directly coupled to a low-temperature amplifier, and their operating temperature is 40 K. Experimental results revealed that the enhanced SNSPD readout circuit achieves a count rate that is approximately 3.5 times greater than that of the traditional circuit. Moreover, the timing jitter of the SNSPD was optimized, decreasing by approximately 3.6 times under high incident photon fluxes. These performance enhancements could significantly improve high-speed optical communication and quantum precision measurement.
We measured the photon count rate (PCR) and dark count rate (DCR) of a superconducting nanowire single photon detector (SNSPD) exposed to either a DC magnetic field (up to 60 mT) or to a low-amplitude oscillating field (0.12–0.48 mT, up to 50 kHz). In both cases, the results show an increase in the PCR and the DCR as the DC field or the frequency of the AC field increase. However, the ratio DCR/(PCR + DCR) increases significantly with an increasing DC field, whereas this ratio is approximately constant as the frequency of the AC field increases up to frequencies in the kHz regime. The results suggest a more favorable effect of AC fields on the operation of the SNSPD.
Superconducting nanowire single-photon detectors (SNSPDs) have shown to be promising in applications such as quantum communication and computation, quantum optics, imaging, metrology and sensing. They offer the advantages of a low dark count rate, high efficiency, a broadband response, a short time jitter, a high repetition rate, and no need for gated-mode operation. Several SNSPD designs have been proposed in literature. Here, we discuss the so-called parallel nanowires configurations. They were introduced with the aim of improving some SNSPD property like detection efficiency, speed, signal-to-noise ratio, or photon number resolution. Although apparently similar, the various parallel designs are not the same. There is no one design that can improve the mentioned properties all together. In fact, each design presents its own characteristics with specific advantages and drawbacks. In this work, we will discuss the various designs outlining peculiarities and possible improvements.
Today Superconducting Nanowire Single-Photon Detectors (SNSPDs) are commonly used in different photon-starved applications, including testing and diagnostics of VLSI circuits. Detecting very faint signals in the near-infrared wavelength range requires not only good detection efficiency, but also very low Dark Count Rate (DCR) and jitter. For example, low noise is crucial to enable ultra-low voltage optical testing of integrated circuits. The effect of detector temperature and background thermal radiation on the noise of superconducting single-photon detectors made of NbN meanders is studied in this paper. It is shown that two different regimes can be identified in the DCR vs. bias current characteristics. At high bias, the dark count rate is dominated by the intrinsic noise of the detector, while at low bias current it is dominated by the detection of stray photons that get onto the SNSPD. Changing the detector temperature changes its switching current and only affects the high bias branch of the characteristics: a reduction of the DCR can be achieved by lowering the SNSPD base temperature. On the other hand, changing the temperature of the single-photon light source (e.g. the VLSI circuit under test) only affects the low bias regime: a lower target temperature leads to a smaller DCR.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
Jitter is one of the key parameters for a superconducting nanowire single photon detector (SNSPD). Using an optimized time-correlated single photon counting system for jitter measurement, we extensively studied the dependence of system jitter on the bias current and working temperature. The signal-to-noise ratio of the single-photon-response pulse was proven to be an important factor in system jitter. The final system jitter was reduced to 18 ps by using a high-critical-current SNSPD, which showed an intrinsic SNSPD jitter of 15 ps. A laser ranging experiment using a 15-ps SNSPD achieved a record depth resolution of 3 mm at a wavelength of 1550 nm.